UROVO i6200s - Powerful Smart Handheld PDA Quick Guide

Lithium ion battery

1. Charge the battery only with original Urovo power adaptor supplied in the box
2. Do not store the device with battery installed for long period of time
3. If long period storage is required, remove battery from device.
4. 4During long storage period, maintenance work is required at every 3 months period. During maintenance, discharge the battery completely, and then charge to 60% - 70% (or 3.8V - 3.9V).
5. Store battery in dry, cool environment. Temperature should be 20 to 40 degree Celsius and relative humidity should be 45% to 85%
6. Charge battery at 5 to 45 degree Celsius
7. Do not operate the device outside the recommended temperature, which is from -20 to 60.
8. Do not install a third party battery into Urovo device

Safety precaution

1. Do not transport the battery at temperature higher than 65 degree Celsius
2. Do expose battery to fire or heat source
3. Do not forcefully install the battery in opposite direction into the device
4. Avoid impact and high vibration force on the battery
5. Keep battery dry at all time
6. Do not use battery that is damaged or appear to have been modified
7. Do not use unauthorized power adaptor to charge the battery
8. Do not discharge the battery beyond the specification of the battery
9. Do not place battery into microwave oven or pressured container
10. Do not damage battery with sharp objects
11. Do not operate in environment with extreme electrostatic fields or magnetic fields.
12. If leakage found in battery, avoid contact with body parts. Should leakage be in contact with body parts, flush with water and immediately seek medical attention
13. If battery exhibits unusual behavior like color change, temperature became hot, shape is swollen, remove battery from device and stop using that battery
14. If the contact point on the battery is dirty, clean with a dry cloth
15. Dispose the battery according local regulation. Recycle if possible.
16. Improper usage or storage may cause battery performance to drop, leak, damage, or even escalate to personal safety issue.

Appearance and Buttons

Front view

To turn on: Hold power button until device switches on
To turn off: Hold power button until the device screen shows the power off menu. Select shutdown on the menu.
Sleep: Under operation mode, press the power button once
Wake up: Press power button once

Side view

1. Audio jack
2. USB connector
3. Scan button
4. User define button
5. Power button
6. Scan button
7. Volume control
8. Reset button

Rear view

1. Contactless reader
2. Battery lock
3. PSAM Slot
4. Micro SD card slot
5. SIM Slot
6. Speaker
7. Camera and LED flash

Battery Installation

Insert the battery into the battery compartment as shown in the picture. Battery should sit tightly in the compartment when correctly installed. Do not apply excessive force when inserting the battery.

Charging using power adaptor

Connect the USB cable into the device and the power adaptor. Red LED indicates charging and Green LED indicates fully charge.

Charging using cradle

Connect the power cable into the cradle.
P: LED indicates the cradle is operational. Slot the device into the cradle and take note of the LED change on the device which indicate the charging process Slot the battery into the cradle as shown in the picture.
C: LED should lit up to indicate charging.

Battery Operation

The device battery is polymer type battery, which should only be charged by using original Urovo power supply.
Metal contact is unavailable or artificial short circuit electrode.
Do not store battery in hot, humid, or corrosive environment.
Do no break or crack battery.
Do not store battery when it is fully charged completely drained. If device is not used for long period of time, remove the battery from the device, pelase.

If the battery is misshapen or is found leaking, replace the battery immediately.
Note: The battery should be charged for at least 8 hours before the first use.

Installing SIM/ TF Card

1. Swing open the main battery cover clip by 90 degrees, you can then remove the battery cover.
2. Insert the SIM card or Micro SD/TF card into their corresponding slots in the battery compartment.
   Note: You should gently push the SIM/TF card to the correct position without using excessive force.

Connecting to PC

After you install the Android driver or an Android smart phone assistant, you can connect the devices to your PC with USB cable provided. (You can download the software mentioned above from www.urovo.com/en. After device connected to your PC, the screen would display like this:

After the device connected to your PC, you could drag the top part of the screen downto show the USB options.

Note: When you enable device as USB Storage to PC, the flash memory of the device are map as a PC drive. At this point of time, you cannot install APK to the device.

To install APK to the device, it should not be in USB Storage mode.