Summary of Contents for Agilent Technologies HP 83711A
Page 1
Notice Hewlett-Packard to Agilent Technologies Transition This documentation supports a product that previously shipped under the Hewlett- Packard company brand name. The brand name has now been changed to Agilent Technologies. The two products are functionally identical, only our name has changed. The document still includes references to Hewlett-Packard products, some of which have been transitioned to Agilent Technologies.
Page 2
Contacting Agilent By internet, phone, or fax, get assistance with all your test and measurement needs. Table 1-1 Contacting Agilent Online assistance: www.agilent.com/find/assist United States Latin America Canada Europe (tel) 1 800 452 4844 (tel) (305) 269 7500 (tel) 1 877 894 4414 (tel) (+31) 20 547 2323 (fax) (305) 269 7599 (fax) (905) 282-6495...
Page 3
Service Guide HP 83711A/12A and HP 83711B/12B Synthesized CW Generators SERIAL NUMBERS ABCDE HP Part No. 83711-90134 Printed in USA July 1997 Supersedes April 1995...
Page 5
Introduction HP 83711A/12A and HP 83711B/12B Synthesized CW Generators Service Guide HP 83711A/12A, HP 83711B/12B, HP 83731A/32A and HP 83731B/32B Synthesized Signal Generators Component-Level Information HP 83711A/12A, HP 83711B/12B, HP 83731A/32A and HP 83731B/32B Synthesized Signal Generators Calibration Guide...
Page 6
In This Guide Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 5 Chapter 6 Chapter 7 Chapter 8 Chapter 9 Chapter 10 Assumptions About You...
Page 15
Troubleshooting Introduction Prior to Beginning Troubleshooting The Service Position Power Supply Verication T roubleshooting...
Page 16
Troubleshooting Safety Considerations Warnings and Cautions Before Applying Power Caution Warning Maintenance described herein is performed with power supplied to the instrument and with protective covers removed. Such maintenance should be performed only by service-trained personnel who are aware of the hazards involved (for example, re and electrical shock). Where maintenance can be performed without power supplied, the power should be removed.
Page 17
Troubleshooting Caution After-Service Safety Checks ESD Precautions Recommended Test Equipment T roubleshooting...
Page 18
Troubleshooting Service Accessories TORX Screwdrivers Pozidrive Screwdrivers Hardware Major Assemblies, Parts, and Cable Locations HP 83711A/12A, HP 83711B/12B, HP 83731A/32A and HP 83731B/32B Synthesized Signal Generators Component-Level Information Test Point Locations T roubleshooting...
Page 19
Troubleshooting Service Aids on Printed Circuit Boards Other Service Documents Cleaning Cleaning Intervals Warning Before cleaning, make sure the instrument is disconnected from the power source. This is to eliminate the possibility of electrical shock. Caution Cleaning Solution 12-Month Cleaning T roubleshooting...
Page 20
Troubleshooting After Repair Calibration HP 83711A/12A, HP 83711B/12B, HP 83731A/32A and HP 83731B/32B Synthesized Signal Generators Calibration Guide Table 1-1. Recommended Test Equipment Equipment Critical Specications Recommended Model T roubleshooting...
Page 21
Troubleshooting Main Troubleshooting SPCL SELF TEST?, PRESS ENTER SPCL PRESETTING INSTRUMENT SELF TESTING! Self Test passed Note 22 = fc T roubleshooting...
Page 23
Troubleshooting Microprocessor Assembly (A3) Troubleshooting Error Group Description Note ABUS Errors Error Group Description Suspect J1 Pin Voltage Voltage Number T roubleshooting...
Page 24
Troubleshooting 0.5 V/GHz Output Errors Error Group Description Frequency Voltage 1-10 T roubleshooting...
Page 25
Troubleshooting LO Synthesizer and Reference Assembly (A6) Troubleshooting Error Group Description Note Data Readback Errors Error Group Description ABUS Errors Error Group Description T roubleshooting 1-11...
Page 26
Troubleshooting ABUS HW CTRL HW CTRL Voltage Voltage ADDRESS VALUE SPCL SPCL Oscillator Cold Error Error Group Description 1-12 T roubleshooting...
Page 27
Troubleshooting LO Synthesizer and Reference Unlocked/Divide Voltage Errors Error Group Description To Troubleshoot an LO Synthesizer/Reference Unlocked Condition T roubleshooting 1-13...
Page 28
Troubleshooting Output Frequency Measured Output Frequency Measured (GHz) Frequency (GHz) Frequency (MHz) (MHz) 1-14 T roubleshooting...
Page 29
Troubleshooting Note To Troubleshoot an Incorrect Synthesizer Divide Voltage Condition Note T roubleshooting 1-15...
Page 30
Troubleshooting YO Loop and Oset Synthesizer Assembly (A7) Troubleshooting Error Group Description Note Data Readback Errors Error Group Description 1-16 T roubleshooting...
Page 31
Troubleshooting ABUS Error Error Group Description SPCL SPCL T roubleshooting 1-17...
Page 32
Troubleshooting Oset Synthesizer Incorrect Frequency/Unlocked Errors Error Group Description To Troubleshoot an Oset Synthesizer Incorrect Frequency/Unlocked Condition 1-18 T roubleshooting...
Page 33
Troubleshooting SPCL Oset Synthesizer Oset Synthesizer Frequency Frequency Note T roubleshooting 1-19...
Page 34
Troubleshooting YIG Driver Assembly (A9) Troubleshooting Error Group Description Note Data Readback Errors Error Group Description ABUS Errors Error Group Description 1-20 T roubleshooting...
Page 35
Troubleshooting ABUS HW CTRL HW CTRL Voltage Voltage ADDRESS VALUE SPCL SPCL MSB Errors Error Group Description T roubleshooting 1-21...
Page 36
Troubleshooting Oset Disconnect Oset Disconnect DAC Address DAC Value Position Address Value SPCL SPCL SPCL MUX Output Voltage Position (max/min) 1-22 T roubleshooting...
Page 37
Troubleshooting SPCL Low/High Band Voltage Errors Error Group Description Error Message Output DAC Output Voltage Number Frequency (max/min) SPCL SPCL T roubleshooting 1-23...
Page 38
Troubleshooting SPCL 1-24 T roubleshooting...
Page 39
Troubleshooting ALC Assembly (A10) Troubleshooting Error Group Description Note Data Readback Errors Error Group Description ABUS Error Error Group Description T roubleshooting 1-25...
Page 40
Troubleshooting SPCL SPCL DAC Errors Error Group Description 1-26 T roubleshooting...
Page 41
Troubleshooting Integrator Errors Error Group Description Integrator Errors (Revision 10.01 and Above Only) Error Group Description Leveled Indicator Trip Point Errors Error Group Description Leveled Indicator Trip Point Errors (Revision 10.01 and Above Only) Error Group Description RF/Reference Detector Errors Error Group Description T roubleshooting...
Page 42
Troubleshooting To Troubleshoot the RF Detector Check Error > Signal Within Tolerance? (Y/N) RF OUTPUT ALC CTRL SIG OUT Action. To Troubleshoot the Reference Detector/Reference Oscillator Check Error 1-28 T roubleshooting...
Page 43
Troubleshooting Input/Output Switching Errors Error Group Description Input/Output Switching Errors (Revision 10.01 and Above Only) Error Group Description Track and Hold Errors Error Group Description Track and Hold Errors (Revision 10.01 and Above Only) Error Group Description T roubleshooting 1-29...
Page 44
Troubleshooting Output Module (A8A1) Troubleshooting Error Group Description Combiner/High Band/Low Band Errors Error Group Description Note 1-30 T roubleshooting...
Page 45
Troubleshooting SLPFA (A8A3) Troubleshooting Error Group Description Input/Output Bias Errors Error Group Description Voltage Number T roubleshooting 1-31...
Page 46
Troubleshooting Failed Frequency Error Number Number 1-32 T roubleshooting...
Page 47
Troubleshooting Failed HW CTRL HW CTRL Voltage Error Number ADDRESS VALUE (max/min) SPCL Note T roubleshooting 1-33...
Page 48
Troubleshooting YO Loop and Oset Synthesizer Assembly (A7) Troubleshooting Error Group Description Note 1-34 T roubleshooting...
Page 49
Troubleshooting Error Group Description T roubleshooting 1-35...
Page 50
Troubleshooting To Troubleshoot a YO Loop Unlocked Condition - General Procedure SPCL 14.749 SPCL SPCL > > 1-36 T roubleshooting...
Page 51
Troubleshooting < T roubleshooting 1-37...
Page 52
Troubleshooting To Troubleshoot a YO Loop Unlocked Condition - Output Frequencies 10 GHz < > > Frequency Power Action Level SPCL 1-38 T roubleshooting...
Page 53
Troubleshooting Table 1-2. YIG Continuity From SPCL T roubleshooting 1-39...
Page 54
Troubleshooting SPCL Note Note 1-40 T roubleshooting...
Page 55
Troubleshooting Sampler (A8T1) Troubleshooting Error Group Description Note LO Unlocked Errors Error Group Description Note T roubleshooting 1-41...
Page 56
Troubleshooting Oset Synthesizer Unlocked Errors Error Group Description Note YO Loop Unlocked Errors Error Group Description To Troubleshoot a YO Loop Unlocked Condition - General Procedure SPCL 1-42 T roubleshooting...
Page 57
Troubleshooting SPCL > > < To Troubleshoot a YO Loop Unlocked Condition - Output Frequencies 10 GHz < T roubleshooting 1-43...
Page 58
Troubleshooting > > Frequency Power Action Level SPCL 1-44 T roubleshooting...
Page 59
Troubleshooting Table 1-3. YIG Continuity From SPCL T roubleshooting 1-45...
Page 60
Troubleshooting SPCL Note To Troubleshoot a YO Loop Unlocked Condition - Output Frequencies 10 GHz > 1-46 T roubleshooting...
Page 61
Troubleshooting > Frequency Power Action Level SPCL T roubleshooting 1-47...
Page 62
Troubleshooting Table 1-4. YIG Continuity From SPCL 1-48 T roubleshooting...
Page 63
Troubleshooting SPCL Note T roubleshooting 1-49...
Page 64
Troubleshooting SLPFA (A8A3) Troubleshooting Error Group Description Note Unleveled at Minimum Vernier Errors Error Group Description 1-50 T roubleshooting...
Page 65
Troubleshooting Unleveled at Maximum Vernier Errors Error Group Description SPCL T roubleshooting 1-51...
Page 66
Troubleshooting Divider and Modulation Assembly (A4) Troubleshooting Error Group Description Note 1-52 T roubleshooting...
Page 67
Troubleshooting Error Group Description T roubleshooting 1-53...
Page 68
Troubleshooting Error Group Description Note Error Group Power Level 1-54 T roubleshooting...
Page 71
Troubleshooting Checking the Power Supply Power Supply Voltages Checking the Front Panel Display Table 1-5. A2J1 Voltages Voltage T roubleshooting 1-57...
Page 72
Troubleshooting Checking the Hewlett-Packard Interface Bus (HP-IB) Checking the Microprocessor 1-58 T roubleshooting...
Page 73
Troubleshooting Checking the 10 MHz Output Checking the 10 MHz Input EX REF EX REF EX REF EX REF EX REF T roubleshooting 1-59...
Page 74
Troubleshooting Checking the 0.5V/GHz Output limit =(frequency (MHz) 2)+0.5 upper limit =(frequency (MHz) 2) 0.5 lower Checking the Output Path Note To Troubleshoot the Option 1E1 Output Path 1-60 T roubleshooting...
Page 79
Major Assembly and Cable Locations Introduction Major Assembly and Cable Locations...
Page 80
Major Assembly and Cable Locations Figure 3-1. Major Assemblies { Top View Major Assembly and Cable Locations...
Page 81
Major Assembly and Cable Locations Figure 3-2. Major Assemblies { Bottom View Major Assembly and Cable Locations...
Page 82
Major Assembly and Cable Locations Figure 3-3. Cable Assemblies { Top View Major Assembly and Cable Locations...
Page 83
Major Assembly and Cable Locations Figure 3-4. Cable Assemblies { Bottom View Major Assembly and Cable Locations...
Page 85
Parts List Introduction HP 83711A/12A, HP 83711B/12B, HP 83731A/32A and HP 83731B/32B Synthesized Signal Generators Component-Level-Information Manual Abbreviations Replaceable Parts Table Format Parts List...
Page 86
Parts List Illustrated Parts Breakdowns Ordering Information Note Parts List...
Page 87
Parts List Optional Congurations Parts List Backdating Parts Identication Parts List...
Page 89
Parts List Exchange Assemblies Table 4-1. Part Numbers for Exchange Assemblies Reference Description Part Number Designator Exchange Assy New Assy Parts List...
Page 90
Parts List Table 4-2. Reference Designations A ....assembly E miscellaneous electrical part P electrical connector (movable V ....electron tube AT .
Page 91
Parts List Table 4-3. Abbreviations (continued) nA ....nanoampere PIV ..peak inverse voltage R&P ..rack and panel TV .
Page 92
Parts List Table 4-5. Major Assemblies, Top View Reference Description Manufacturer Designation Part No. Code Part Number Figure 4-1. Major Assemblies Location Diagram (Top View) Parts List...
Page 93
Parts List Table 4-6. Major Assemblies, Bottom View Reference Description Manufacturer Designation Part No. Code Part Number Parts List...
Page 94
Parts List Figure 4-2. Major Assemblies Location Diagram (Bottom View) 4-10 Parts List...
Page 95
Parts List Table 4-7. Cable Assemblies, Top View Reference Description Manufacturer Designation Part No. Code Part Number Parts List 4-11...
Page 96
Parts List Figure 4-3. Cable Assemblies Location Diagram (Top View) 4-12 Parts List...
Page 97
Parts List Table 4-8. Cable Assemblies, Bottom View Reference Description Manufacturer Designation Part No. Code Part Number Parts List 4-13...
Page 98
Parts List Figure 4-4. Cable Assemblies Location Diagram (Bottom View) 4-14 Parts List...
Page 99
Parts List Figure 4-5. Figures Orientation Diagram, Top View Parts List 4-15...
Page 100
Parts List Figure 4-6. Figures Orientation Diagram, Bottom View 4-16 Parts List...
Page 101
Parts List Table 4-9. Illustrated Replaceable Parts (Figure 4-7) Reference Description Manufacturer Designation Part No. Code Part Number Parts List 4-17...
Page 102
Parts List Figure 4-7. Top and Bottom Cover Illustrated Parts Breakdown 4-18 Parts List...
Page 103
Parts List Table 4-10. Illustrated Replaceable Parts (Figure 4-8) Reference Description Manufacturer Designation Part No. Code Part Number Parts List 4-19...
Page 104
Parts List Figure 4-8. Front Panel Illustrated Parts Breakdown 4-20 Parts List...
Page 105
Parts List Table 4-11. Illustrated Replaceable Parts (Figure 4-9) Reference Description Manufacturer Designation Part No. Code Part Number Parts List 4-21...
Page 106
Parts List Figure 4-9. Front Frame and Display/Keyboard Illustrated Parts Breakdown 4-22 Parts List...
Page 107
Parts List Table 4-12. Illustrated Replaceable Parts (Figure 4-10) Reference Description Manufacturer Designation Part No. Code Part Number Parts List 4-23...
Page 108
Parts List Figure 4-10. Front Dress Panel Illustrated Parts Breakdown 4-24 Parts List...
Page 109
Parts List Table 4-13. Illustrated Replaceable Parts (Figure 4-11) Reference Description Manufacturer Designation Part No. Code Part Number Parts List 4-25...
Page 110
Parts List Figure 4-11. Top Side Circuit Board Illustrated Parts Breakdown 4-26 Parts List...
Page 111
Parts List Table 4-14. Illustrated Replaceable Parts (Figure 4-12) Reference Description Manufacturer Designation Part No. Code Part Number Parts List 4-27...
Page 112
Parts List Figure 4-12. Fan, Power Supply, and Rear Panel Connector Illustrated Parts Breakdown 4-28 Parts List...
Page 113
Parts List Table 4-15. Illustrated Replaceable Parts (Figure 4-13) Reference Description Manufacturer Designation Part No. Code Part Number Parts List 4-29...
Page 114
Parts List Figure 4-13. YIG, Crystal Oscillator, and Sampler Microcircuit Illustrated Parts Breakdown 4-30 Parts List...
Page 115
Parts List Table 4-16. Illustrated Replaceable Parts (Figure 4-14) Reference Description Manufacturer Designation Part No. Code Part Number Parts List 4-31...
Page 116
Parts List Figure 4-14. Attenuator, Bottom Side Circuit Board, and Rails Illustrated Parts Breakdown 4-32 Parts List...
Page 117
Parts List Table 4-17. Illustrated Replaceable Parts (Figure 4-15) Reference Description Manufacturer Designation Part No. Code Part Number Parts List 4-33...
Page 118
Parts List Figure 4-15. Microwave Output and SLPFA Illustrated Parts Breakdown 4-34 Parts List...
Page 119
Parts List Table 4-18. Illustrated Replaceable Parts (Figure 4-16) Reference Description Manufacturer Designation Part No. Code Part Number Parts List 4-35...
Page 120
Parts List Figure 4-16. Microwave Deck Illustrated Parts Breakdown 4-36 Parts List...
Page 129
Assembly Replacement Special Techniques Safety Warning Disassembly procedures must be performed with the power cable disconnected from the synthesizer. Do not reconnect power until you have an assembly in the service position and are ready for troubleshooting. Caution Fasteners (Screws and Nuts) Table 5-2.
Page 137
Assembly Replacement Power Supply (A11) To Disconnect the Power Supply Cables service position Assembly Replacement 5-17...
Page 138
Assembly Replacement Figure 5-8. Power Supply Cables To Remove the Power Supply Note 5-18 Assembly Replacement...
Page 139
Assembly Replacement Figure 5-9. Power Supply Screws Reassembly Tips Warning Use the original screws to mount the power supply to the chassis. Longer screws may damage insulation internal to the power supply, resulting in a possible shock hazard. Assembly Replacement 5-19...
Page 140
Assembly Replacement Fuse To Remove (and Replace) the Fuse Warning For continued protection against re hazard, replace the fuse with the same type and rating. Figure 5-10. Line Fuse Removal and Replacement 5-20 Assembly Replacement...
Page 141
Assembly Replacement Fan Assembly To Disconnect the Fan Cable Figure 5-11. Fan Cable Location Assembly Replacement 5-21...
Page 142
Assembly Replacement To Remove the Fan Figure 5-12. Fan Assembly Removal 5-22 Assembly Replacement...
Page 143
Assembly Replacement Reassembly Tips Divider and Modulation Board Assembly (A4) Note To Access the Service Position service position service position To Remove the Assembly Assembly Replacement 5-23...
Page 146
Assembly Replacement Microprocessor Board Assembly (A3) To Access the Service Position service position service position To Disconnect the Cables service position 5-26 Assembly Replacement...
Page 149
Assembly Replacement Battery (A3BT1) Note To Access the Service Position service position service position To Remove the Part Warning To prevent battery explosion, do not apply excess heat when unsoldering or soldering the battery. Note Assembly Replacement 5-29...
Page 150
Assembly Replacement Figure 5-16. Microprocessor Board Battery Removal To Reassemble the Instrument Note 5-30 Assembly Replacement...
Page 151
Assembly Replacement Crystal Oscillator (Option 1E5) To Disconnect the Oscillator Cables service position Figure 5-17. Crystal Oscillator Cables To Remove the Oscillator Assembly Replacement 5-31...
Page 155
Assembly Replacement YIG Driver Board Assembly (A9) To Access the Service Position service position service position Figure 5-20. YIG Driver Board Service Position Assembly Replacement 5-35...
Page 156
Assembly Replacement To Remove the Assembly 5-36 Assembly Replacement...
Page 158
Assembly Replacement YO (YIG Oscillator) Loop/Oset Synthesizer Board Assembly (A7) To Remove the Assembly service position Note Reassembly Tips 5-38 Assembly Replacement...
Page 159
Assembly Replacement Figure 5-22. YO Loop and Oset Synthesizer Board Removal Assembly Replacement 5-39...
Page 160
Assembly Replacement LO (Local Oscillator) Synthesizer/ Reference Board Assembly (A6) To Access the Service Position service position service position 5-40 Assembly Replacement...
Page 161
Assembly Replacement Figure 5-23. LO Synthesizer and Reference Board Service Position To Remove the Assembly Assembly Replacement 5-41...
Page 163
Assembly Replacement Figure 5-24. LO Synthesizer and Reference Board Removal Assembly Replacement 5-43...
Page 164
Assembly Replacement Step Attenuator, A8AT1 (Option 1E1) To Remove the Assembly Caution service position To Reassemble the Instrument Caution 5-44 Assembly Replacement...
Page 168
Assembly Replacement To Reassemble the Instrument Caution Ignore all label hookup instructions 5-48 Assembly Replacement...
Page 169
Assembly Replacement YIG Oscillator(s) Note To Remove the Part service position Note Note only will not slight Note Assembly Replacement 5-49...
Page 170
Assembly Replacement Note To Reassemble the Instrument Note 5-50 Assembly Replacement...
Page 173
Assembly Replacement YIG Driver Cable and Temperature Transducer Note To Remove the Part Note service position slight will not Assembly Replacement 5-53...
Page 174
Assembly Replacement To Reassemble the Instrument 5-54 Assembly Replacement...
Page 175
Assembly Replacement Output Module, SLPFA Module, and Coupler/Detector To Remove the Subassemblies Caution service position Assembly Replacement 5-55...
Page 176
Assembly Replacement Figure 5-28. Output Module, SLPFA Module, and Coupler/Detector Removal To Remove the Coupler/Detector Subassembly 5-56 Assembly Replacement...
Page 178
Assembly Replacement To Remove the Output Module and the SLPFA Module Subassemblies slight To Reassemble the Instrument Caution 5-58 Assembly Replacement...
Page 196
Manual Error Number Error Message 222, Data out of range;CW FREQ(2003) SCPI Error Number SCPI Error Message Data out of range Detailed Description CW FREQ Action Required Notes HP 83711A/12A and HP 83711B/12B Synthesized CW Generators Service Guide Error Messages...
Page 199
Error Messages 222,"Data out of range;( 222)" 221,"Settings con
ict;( 221)" 220,"Parameter error;( 220)" 213,"Init ignored;( 213)" 212,"Arm ignored;( 212)" 211,"Trigger ignored;( 211)" 210,"Trigger error;( 210)" 201,"Invalid while in local;( 201)" 200,"Execution error;( 200)" 184,"Macro parameter error;( 184)" 183,"Invalid inside macro denition;( 183)" 181,"Invalid outside macro denition;( 181)"...
Page 200
Error Messages 171,"Invalid expression;( 171)" 170,"Expression error;( 170)" 168,"Block data not allowed;( 168)" 161,"Invalid block data;( 161)" 160,"Block data error;( 160)" 158,"String data not allowed;( 158)" 151,"Invalid string data;( 151)" 150,"String data error;( 150)" 148,"Character data not allowed;( 148)" 144,"Character data too long;( 144)" 141,"Invalid character data;( 141)"...
Page 201
Error Messages 130,"Sux error;( 130)" 128,"Numeric data not allowed;( 128)" 124,"Too many digits;( 124)" 123,"Exponent too large;( 123)" 121,"Invalid character in number;( 121)" 120,"Numeric data error;( 120)" 114,"Header sux out of range;( 114)" 113,"Undened header;( 113)" 112,"Program mnemonic too long;( 112)" 111,"Header separator error;( 111)"...
Page 202
Error Messages 103,"Invalid separator;( 103)" 102,"Syntax error;( 102)" 101,"Invalid character;( 101)" 100,"Command error;( 100)" 0,"No error" 110,"EEPROM unprotected;(110)" 511,"YTO cal data init error;(511)" 600,"ALC loop went unleveled;(600)" 601,"Hardware driver Power limit;(601)" 602,"Vernier has been set to the limit;(602)" 603,"RF on/o command not valid;(603)" 604,"Atten driver error while setting level;(604)"...
Page 203
Error Messages 606,"Level is not in guaranteed range.;(606)" 608,"Attenuator not set before Ext Meter mode;(608)" 610,"Track and hold failed, level is invalid;(610)" 611,"Track and hold failed, level is invalid;(611)" 650,"PG switch not set to 0;(650)" 651,"Invalid vernier cal data for 1-20 GHz;(651)" 652,"ALC term verication after EEPROM write;(652)"...
Page 204
Error Messages 701,"Lo synthesizer set error;(701)" 702,"Oset synthesizer set error;(702)" 704,"YTO driver set error;(704)" 706,"Low pass lter set error;(706)" 709,"Hardware driver Frequency limit;(709)" 710,"LO synthesizer went out of lock;(710)" 711,"Oset synthesizer went out of lock;(711)" 712,"Frequency loop went out of lock;(712)" 730,"Invalid data in level correct table;(730)"...
Page 205
Error Messages 735,"Level correct points less than 2;(735)" 736,"Factory level corr 1-20 GHz, 1-9 table;(736)" 737,"Factory level corr 0.01-1 GHz, 1-9 table;(737)" 738,"Factory level corr 0.01-1 GHz, 0 dB table;(738)" 739,"Invalid data in table, not recalled;(739)" 740,"Another controller is on the HP-IB bus;(740)" 741,"No HP-IB devices found;(741)"...
Page 206
Error Messages 745,"Meter returns error msg;(745)" 746,"Data measured is invalid or out of range;(746)" 747,"Unable to receive msg from meter;(747)" 748,"Erasing corrupted level correct table;(748)" 749,"Frequency not within level correct data;(749)" 751,"Parameters cause points to be too large;(751)" 222,"Data out of range;Data set to minimum(752)" 222,"Data out of range;Data set to maximum(753)"...
Page 207
Error Messages 760,"Bad index into data table;(760)" 761,"Bad index into oset table;(761)" 763,"Unable to write to EEPROM;(763)" 764,"Unable to write to RAM;(764)" 765,"Attempt to write to ROM;(765)" 766,"Number of writes to EEPROM exceeds max;(766)" 770,"YTO cal data invalid;(770)" 771,"Invalid YIG DAC value in cal table.;(771)" 772,"YTO cal values for Up/Down search vary;(772)"...
Page 208
Error Messages 777,"Low band yto cal could not write EEPROM;(777)" 778,"High band yto cal could not write EEPROM;(778)" 779,"Only 2GHz or 10GHz allowed for YTO Cal;(779)" 785,"Cal Data not saved, PG switch is not 0;(785)" 786,"Cal Data verication after EEPROM write;(786)" 787,"FM cal and Pincho cal not initialized;(787)"...
Page 209
Error Messages 802,"Assembly Revs not saved, PG switch is not 0 (802)" 803,"EEPROM not cleared, PG switch is not 0 (803)" 900,"PRI increased to t pulse width;(900)" 901,"Delay and width decreased to t max PRI;(901)" 940,"Oven is cold;(940)" 944,"Reference synthesizer went out of lock;(944)" 1101,"Loop number is invalid.;(1101)"...
Page 210
Error Messages 1109,"Query Port mode;(1109)" 1462,"Keybd processor reports status error;(1462)" 1463,"Keybd processor data lines incorrect;(1463)" 302,"8673 command not recognized (1501)" 301,"8673 command K0 not emulated (1511)" HP 8673 Compatibility Guide 301,"8673 command K1 not emulated (1512)" HP 8673 Compatibility Guide 301,"8673 command Mn not emulated (1513)"...
Page 211
Error Messages 301,"8673 command 9 not emulated (1518)" HP 8673 Compatibility Guide 301,"8673 command OC not emulated (1519)" HP 8673 Compatibility Guide 301,"8673 command CT not emulated (1520)" HP 8673 Compatibility Guide 301,"8673 command Nx not emulated (1521)" HP 8673 Compatibility Guide 301,"8673 command SU not emulated (1522)"...
Page 212
Error Messages 301,"8673 command 3 not emulated (1529)" HP 8673 Compatibility Guide 301,"8673 command A not emulated (1530)" HP 8673 Compatibility Guide 301,"8673 command SV not emulated (1531)" HP 8673 Compatibility Guide 301,"8673 command OL not emulated (1532)" HP 8673 Compatibility Guide 301,"8673 command FA not emulated (1534)"...
Page 213
Error Messages 301,"8673 command IF not emulated (1541)" HP 8673 Compatibility Guide 1802,"Low Battery Voltage;(1802)" 1803,"RAM data lost at power on;(1803)" 1804,"Self test failure, run the self test;(1804)" 1805,"Processor Board or IBUS test Failure;(1805)" 1806,"ROM checksum test failure;(1806)" 222,"Data out of range;CW FREQ(2003)" 222,"Data out of range;POWER LEVEL(2006)"...
Page 214
Error Messages 222,"Data out of range;POWER LEVEL INCR(2033)" 222,"Data out of range;EXT METER LEVEL(2036)" 222,"Data out of range;DIAG:IBUS:DIR(2042)" 224,"Illegal parameter value; *EMC (2045)" 222,"Data out of range;SYST:KEY(2048)" 161,"Invalid block data;SYST:SET bad size(2051)" 222,"Data out of range;CAL:ALC:CURV(2054)" 222,"Data out of range;HPIB ADDRESS(2057)" 222,"Data out of range;SAVE(2060)"...
Page 215
Error Messages 222,"Data out of range;CAL:YIG(2090)" 222,"Data out of range;FREQ MULTIPLIER(2099)" 222,"Data out of range;EXT METER INCR(2102)" 222,"Data out of range;CAL:ALC:CURV:FREQ(2105)" 224,"Illegal parameter value; *PSC (2111)" 224,"Illegal parameter value;ATTEN LOCK(2114)" 224,"Illegal parameter value;REMOTE LANGUAGE(2165)" 222,"Data out of range;CAL:FLAT(2177)" 224,"Illegal parameter value;DISPLAY STATE(2189)" 224,"Illegal parameter value;...
Page 216
Error Messages 222,"Data out of range;LO FREQ INCR(2240)" 222,"Data out of range;DIRECT HW CONTROL INC(2243)" 222,"Data out of range;DIAG:ABUS?(2249)" 222,"Data out of range;CORR:FLAT(2276)" 2277,"CORR:FLAT cannot query empty table;(2277)" 224,"Illegal parameter value;SERIAL NUM(2291)" 151,"Invalid string data;SERIAL NUM bad char(2292)" 222,"Data out of range;POW METER ADDRESS(2294)" 222,"Data out of range;CAL:FLAT:FREQ:START(2300)"...
Page 217
Error Messages 2457,"RF on before running level correct;(2457)" 222,"Data out of range;LEVEL CORR START INC(2462)" 222,"Data out of range;LEVEL CORR STOP INC(2465)" 222,"Data out of range;HPIB ADDRESS INCR(2471)" 222,"Data out of range;YIG OSC CAL FREQ INC(2474)" 222,"Data out of range;POW METER ADDRESS INC(2522)" 222,"Data out of range;NODE MEASURE INC(2525)"...
Page 218
Error Messages 222,"Data out of range;MEM:TABL:LOSS(2597)" 2598,"MEM:TABL:LOSS cannot query empty table;(2598)" 222,"Data out of range;ADD OPTION(2702)" 222,"Data out of range;DELETE OPTION(2705)" 330,"Self test failed;(4000)" 330,"Self test failed;(4001)" 330,"Self test failed;(4002)" 330,"Self test failed;(4003)" 330,"Self test failed;(4004)" 330,"Self test failed;(4005)" 330,"Self test failed;(4006)" 330,"Self test failed;(4007)"...
Page 219
Error Messages 330,"Self test failed;(4010)" 330,"Self test failed;(4011)" 330,"Self test failed;(4012)" 330,"Self test failed;(4013)" 330,"Self test failed;(4014)" 330,"Self test failed;(4015)" 330,"Self test failed;(4016)" 330,"Self test failed;(4017)" 330,"Self test failed;(4018)" 330,"Self test failed;(4019)" 330,"Self test failed;(4020)" 330,"Self test failed;(4021)" 330,"Self test failed;(4022)" 330,"Self test failed;(4023)"...
Page 220
330,"Self test failed;(4029)" 330,"Self test failed;(4030)" 330,"Self test failed;(4031)" 330,"Self test failed;(4032)" 330,"Self test failed;(4033)" 330,"Self test failed;(4034)" 330,"Self test failed;(4035)" 330,"Self test failed;(4036)" 330,"Self test failed;(4037)" 330,"Self test failed;(4038)" 330,"Self test failed;(4039)" 330,"Self test failed;(4040)" 330,"Self test failed;(4041)" 330,"Self test failed;(4042)" 330,"Self test failed;(4043)"...
Page 221
330,"Self test failed;(4044)" 330,"Self test failed;(4045)" 330,"Self test failed;(9000)" Many dierent error messages can occur here. Error Messages 7-27...
Page 225
Options Mechanical Options Option 1CM - Rack Mount Kit Option 1CP - Rack Mount and Handle Kit Option 1CR - Rack Slide Kit Warranty Options Option W30 - Two Additional Years Return-to-HP Service Option W32 - Three Year Return to HP Calibration Service Options...
Page 226
HP 83711A/12A and HP 83711B/12B Synthesized CW Generators User's Guide HP 83711A/12A and HP 83711B/12B Synthesized CW Generators Programming Guide HP 83711A/12A and HP 83711B/12B Synthesized CW Generators Quick Start Guide HP 83711A/12A, HP 83711B/12B, HP 83731A/32A, and HP 83731B/32B Synthesized CW Generators Calibration Guide...
Page 228
Contacting Hewlett-Packard Returning Instruments for Service Service Tag Original Packaging Other Packaging Caution Contacting Hewlett-Packard...
Page 229
Contacting Hewlett-Packard Sales and Service Oces Contacting Hewlett-Packard...
Page 230
Legal and Regulatory Information Introduction Legal and Regulatory Information 10-1...
Page 231
Legal and Regulatory Information Safety Considerations Before Applying Power Safety Earth Ground Warning Any interruption of the protective (grounding) conductor (inside or outside the system) or disconnecting the protective earth terminal will cause a potential shock hazard that could result in personal injury. (Grounding one conductor of a two conductor outlet is not sucient protection.) In addition, verify that a common ground exists between the unit under test and the system prior to energizing either unit.
Page 232
Legal and Regulatory Information Safety Symbols and Notes Warning The WARNING sign denotes a hazard. It calls attention to a procedure, practice, or the like which, if not correctly performed or adhered to, could result in personal injury. Do not proceed beyond a WARNING sign until the indicated conditions are fully understood and met.
Page 233
Legal and Regulatory Information Electrostatic Discharge Figure 10-1. Static-Safe Workstation PC Board Assemblies and Electronic Components Caution 10-4 Legal and Regulatory Information...
Page 234
Legal and Regulatory Information Test Equipment ESD Accessories Description Dimensions HP Part No. Reusable 6 to 12 Months One-Time Use Only Description Dimensions HP Part No. Legal and Regulatory Information 10-5...
Page 235
Legal and Regulatory Information Certication Hewlett-Packard Company certies that this product met its published specications at the time of shipment from the factory. Hewlett-Packard further certies that its calibration measurements are traceable to the United States National Institute of Standards and Technology, (NIST), to the extent allowed by the Institute's calibration facility, and to the calibration facilities of other International Standards Organization members.