Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Greengage ALIS IPH500230
Summary of Contents for Greengage ALIS IPH500230
- Page 1 Version CE and UL...
-
Page 2: Alis Barn Lamp Best Practice Clip On Procedure
ALIS Barn Lamp best practice clip on procedure The new ALIS Barn Lamp has been designed with improved durability and ingress protection against dust and high- pressure water jets. To ensure the longevity of the lamp it is important to follow the correct fixing procedure. At the desired lamp position un-twist, Undo the side clips by holding the Lift the upper coupler back on its... -
Page 3: Disclaimer
All electrical installation work must conform to all local and international electrical wiring and safety regulations such as those published by local governing body and sites specific. Installers should contact Greengage Lighting Ltd technical support with any queries they may have at support@greengage.global relating to installation. -
Page 4: Table Of Contents
Contents ALIS Barn Lamp best practice clip on procedure ....................1 Disclaimer ................................2 Safety ................................2 Tools ................................. 4 Mounting accessories ............................4 System description ............................. 5 ALIS system components ............................ 5 For use only with parts as indicated ........................6 Installation procedures ............................ -
Page 5: Tools
Tools Below is a list of basic tools necessary for carrying out your installation. Other tools may be required depending on the exact suspension, mounting method used and the composition of the surface mounting material. Tape Measure Screwdrivers inc. terminal driver Cable cutters, crimpers and wire Pliers strippers... -
Page 6: System Description
System description The Greengage induction system (ALIS) is a 'contactless' power technology that allows LED fixtures (ALIS Lamps) to be clipped onto the cable (ALIS Bus) without an actual physical electrical connection. This document serves as guidance for an ALIS installation. Installers must also follow all applicable local mechanical and electrical installation standards when carrying out the installation. -
Page 7: For Use Only With Parts As Indicated
For use only with parts as indicated Component parts Model Model Additional UL cULus Requirements/Use ALIS Power Hub IPH500230 IPH500110 Install only in dry locations. (500W) (or suitable enclosure to meet local regulations) ALIS Bus ALS0018 ALS0035 Type USE-2 cable or Type RHH-2 wire marked VW-1.14AWG standard type rated... - Page 8 Component parts Model Model Additional UL cULus Requirements/Use ALIS Dimmer IPD1230 IPD1110 Install only in dry component locations. ALIS Dimmer Plastic Enclosure Kit Assembly ALS0040 ALS0040 (or suitable enclosure to ALIS Dimmer in meet local regulations) ALS0045 ALS0046 Plastic Enclosure ALIS Bus End ETM/Short ETM/Short...
-
Page 9: Installation Procedures
Installation procedures Introduction The installation procedures section is divided into three parts; mechanical, lamp connection and electrical. Each section must be carried out by suitably trained competent personnel. Care must be taken on the electrical installation as local electrical regulations may apply. 1. -
Page 10: Alis Power Hub Mounting
1.2 ALIS Power Hub Mounting It is recommended that the ALIS Power Hub is mounted vertically on a non-combustible surface, mounted away from sources of heat, water and direct sunlight and in accordance with site and local regulations. Clearances of 100mm (4”) top and bottom, and 75mm (3”) from left to right are recommended, this is to allow good air flow. - Page 11 Once the ALIS Bus is positioned within the coupler housing, carefully bring the two coupler sections together and close. It is recommended to close the end clips first and then close the side clips by pressing on their outside surfaces rather than the thumb levers.
-
Page 12: Alis Nest Lamp
2.2 ALIS Nest Lamp The lamp positioning information is found within the lighting design plan. If there is not any positioning information available, then fit to achieve the required lighting level within the nest box. At the desired lamp position un-twist, the ALIS Bus to allow fitting of the nest lamp. -
Page 13: Electrical Installation
3. Electrical installation 3.0 General Guidance In this section you will find all the necessary information for the electrical installation. This describes the process of electrically connecting the components. Each of the components of the system will be handled in a separate paragraph. -
Page 14: End Termination
3.2 End termination All ALIS Dimmer Models. The correct termination of the ALIS BUS is critical to the overall system performance. See also section 3.3 of this manual. Connect the ALIS End Termination Module (ETM) or shorting terminal block to the far open end of the ALIS Bus. Strip the ends of the ALIS Bus to 5mm (0.2 “) of exposed conductor, ensuring there is not any conductor loss as shown below. -
Page 15: Hub Supply Cable Termination (Ce)
Connect the P2M Connector to a 3-core suitably rated mains supply cable by inserting into the screw terminals as shown below. Ensure there are no frayed copper strands and the supply is suitably protected to meet all local wiring regulations and sites specific. Not applicable if installing a Greengage Power Hub Panel. Example. -
Page 16: Hub Supply Cable Termination (Ul)
Dimmer Pot or a 0-10VDC control signal, ensuring polarity is maintained, as shown in the ALIS system components diagram (page 5). Connecting ALIS Dimmer to ALIS Pot/0-10VDC (Not applicable if installing the Greengage Power Hub Panel). Connectors of the same shape can be connected. -
Page 17: Installation Checklist And System Test
1. Double check the ALIS Bus cable length connected to the ALIS Power Hub. This should not exceed 150 metres. If in doubt contact support@greengage.global 2. Count the number of lamps per ALIS Bus per ALIS Power Hub. This should not exceed specified limits. If in doubt contact support@greengage.global... -
Page 18: Fault Finding
5. Fault finding If the ALIS Lamps flash ON and OFF, this means there is too much load on the system. Start removing the ALIS Lamps one at a time until the flashing stops. Recheck the recommended maximum number of lamps as shown in section 3.3 and 4. -
Page 19: Fault Finding Guide
Replace Hub • If any problems or faults occur that are outside any of the above, or you are having difficulties, please contact support@greengage.global for further guidance. Page 18 of 33 28 August 2019 Version 5.4 • CE and UL • ALIS Barn Lamp and ALIS Nest Lamp... -
Page 20: General Points And Good Practices
13. Under no circumstances must the ALIS Bus be switched by any means, be that relay, contactor, isolator or circuit breaker, unless parts are supplied by Greengage Lighting for that purpose. If this is attempted the subsequent damage caused to the ALIS Power Hub will not be covered by any Product Warranty. -
Page 21: Care With Lighting
7. Care with Lighting When it comes to caring for you ALIS system, as with all equipment, it is important to adhere to the best practice recommendations. The ALIS system is designed to be robust and reliable and able to withstand chemicals used within many washdown routines. -
Page 22: Specifications
7. Specifications 7.1 ALIS Power Hub electrical 7.1.1 Input Specifications 230VAC (CE) Parameter Description Minimum Nominal Maximum VAC RMS Input Supply Frequency AC RMS (Hz) AC Start Up Input Start Voltage (V) AC Shut Down Input Stop Voltage (V) Current Current RMS (A) Insulation information: Secondary output circuit of IPH500 is separated from its Primary input circuit by basic insulation;... -
Page 23: Alis Power Hub Environmental
7.2 ALIS Power Hub environmental Parameter Description Minimum Nominal Maximum Operating Temperature Thermal Environment -40˚C 25˚C 40˚C Non-operating Temperature Thermal Environment -40˚C 70˚C Storage Temperature ALIS Bus -40˚C 100˚C Operating Humidity Non-condensing Non-operating Humidity Non-condensing Operating Altitude Maximum 3,000m or 10,000 feet Non-operating Altitude Max 15,000m or 50,000 feet Enclosure rating. -
Page 24: Alis Barn Lamp
7.3 ALIS Barn Lamp Parameter Specification Light Source 10W High Power CoB LED (3500K) Luminous Flux 1000 lumens (ALIS Barn Lamp Narrow beam) 1100 lumens (ALIS Barn Lamp Wide beam) Optics Optical grade milky white polycarbonate lens. Connection Type Clip on Dimmer Option 100K potentiometer or 0-10V Environmental Rating... -
Page 25: Compliance
8. Compliance 8.1 ALIS Power Hub 230VAC (CE) This equipment complies with 2014/30/EC Electromagnetic Compatibility Directive and 2014/35/EC Low Voltage Directive as demonstrated by conformity with the applicable requirements of the following documents: Title Description Edition/Date EN 55015 Limits and methods of measurement of radio disturbance 2013 + A1:2015 characteristics of electrical lighting and similar equipment EN 61547... -
Page 26: Alis Lamps (Ce)
8.3 ALIS Lamps (CE) This equipment complies with 2014/30/EC Electromagnetic Compatibility Directive and 2014/35/EC Low Voltage Directive as demonstrated by conformity with the applicable requirements of the following documents: Title Description Edition/Date EN 55015 Limits and methods of measurement of radio disturbance 2013 + A1:2015 characteristics of electrical lighting and similar equipment EN 61547... - Page 27 Page 26 of 33 28 August 2019 Version 5.4 • CE and UL • ALIS Barn Lamp and ALIS Nest Lamp...
-
Page 28: Warranty Validation
Warranty validation To validate the warranty of the ALIS system, please complete the form below and send to warranty@greengage.global or/and Warranty Registration Greengage Lighting Ltd Roslin Innovation Centre Charnock Bradley Building The University of Edinburgh Easter Bush Campus Midlothian EH25 9RG... -
Page 29: Install Information
Install Information Dimming Facility ALIS Power Hub ALIS Dimmer Length of Number of ALIS Serial Number Serial Number Cable Barn Lamps ALIS Pot 0-10VDc Pictures Please send pictures of the following a. The installed ALIS Power Hubs and ALIS Dimmers b. -
Page 30: Connection Diagram
Appendix 1 Connection diagram Twin Hub Panel Wiring Page 29 of 33 Version 5.4 • CE and UL • ALIS Barn Lamp and ALIS Nest Lamp 28 August 2019... - Page 31 Notes Page 30 of 33 28 August 2019 Version 5.4 • CE and UL • ALIS Barn Lamp and ALIS Nest Lamp...
- Page 32 Notes Page 31 of 33 Version 5.4 • CE and UL • ALIS Barn Lamp and ALIS Nest Lamp 28 August 2019...
- Page 33 Page 32 of 33 28 August 2019 Version 5.4 • CE and UL • ALIS Barn Lamp and ALIS Nest Lamp...
- Page 34 Page 33 of 33 Version 5.4 • CE and UL • ALIS Barn Lamp and ALIS Nest Lamp 28 August 2019...
Need help?
Do you have a question about the ALIS IPH500230 and is the answer not in the manual?
Questions and answers