1. Manuals
  2. Brands
  3. Logosol Manuals
  4. Cutter
  5. Stack Cutter 1200
  6. Manual

Logosol Stack Cutter 1200 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Manual
Stack Cutter
1

Advertisement

Table of Contents
loading

Related Manuals for Logosol Stack Cutter 1200

Summary of Contents for Logosol Stack Cutter 1200

  • Page 1 Manual Stack Cutter...

  • Page 3: Table Of Contents

    Stack Cutter, please do not hesitate to call LOGOSOL. Our goal is that you too will become Stack Cutter cuts with great precision. A measuring stick yet another satisfied owner of a LOGOSOL product.

  • Page 4: Safety Instructions

    Safety instructions Workplace In addition to the instructions given here on pages 4 and 5, further warnings and reminders are given throughout the manual. For the greatest electrical safety, ensure an earth-leak circuit breaker is fitted. When using Stack Cutter, always have a fire For your own safety, read this manual thoroughly extinguisher within easy reach.
  • Page 5 Do not start stack cutting before all the operations The machine must not be modified or added to. Use described in “Preparing stacks for cutting” (page 8) have only parts supplied by LOGOSOL. After servicing, the been carried out. machine must be returned to its original condition.
  • Page 6 Directions as given in user instructions. Forwards/back- wards is relative to Forwards Left (sideways) the alignment of the guide bar. Right (sideways) Backwards Fixed guide bar Saw unit guard Belt drive Oil tank Corner with lifting Motor bracket Adjustable guide bar guard Handling bar Sighting rod and...

  • Page 7: Moving The Cutter

    Using hose clips at both the machine end and the fan end, connect the hose for the chip fan. Ensure that the lighting is first-class. Fit a powerful light End trimming with Logosol’s Stack Cutter above the machine. Note where the operator is standing, the position of his Check that all bolts are correctly tightened.

  • Page 8: Preparing Stacks For Cutting

    Preparing stacks for cutting cuts. Do not forget to take the cut’s width into account. Exact measurements are made between each saw cut Ensure that there is no electrical power to the machine (see “Setting cut length”). while the stack is being prepared. The ground where the stack is set up should be flat End trimming (F) refers to cutting the end off a stack.
  • Page 9 Control panel Electrical connection Do not connect the machine to a power supply Risk of electric shock. before you have read and understood the entire Do not connect the machine to a power supply before manual. Incorrect use may result in a fatal you have read and understood the entire manual.
  • Page 10 The maximum permitted distance between the stack and the guide bar guard is 50 mm. Long guide bar guards can be ordered from Logosol. So that you do not saw through anything unintentionally, check the guide bar’s path and the ground beneath the guide bar.

  • Page 11: Cut Positioning

    Drawing the line for end trimming The sighting rod must be on the side of the stack that is not going to be taken away. The basic procedure when using Stack Cutter is to mark The sighting rod’s holder must be fitted in such a way that out the intended cut by drawing lines on the stack’s you can measure close to the centre of the stack.

  • Page 12: Setting Cut Length

    Setting cut length End trimming At the top and the bottom of both sides of the stack, set the stop plate against the cut surface and mark the end of the rod. Once one of the stack’s ends has been trimmed, the cut surface On both sides of the stack, draw a line between the marks.

  • Page 13: Changing Cutting Equipment

    To guarantee that the correct equipment is used, saw chains, chain sprockets and guide bars should be purchased from Logosol. A new chain may need re-tensioning after the first or second cut.

  • Page 14: Maintenance - Cutting Equipment

    Maintenance – cutting equipment Sharpening the chain – keep the edge in the chromium layer! If you keep your cutting equipment in good condition, the sawn product will have the right dimensions, cutting will The cutters on the chain of a motor saw are coated with be speedy and the equipment will last longer.

  • Page 15: Troubleshooting - Cutting Equipment

    Troubleshooting – cutting equipment A guide bar that has been worn at an angle can be repaired. Using, for example, a UKF file (art. no. 9999-000-0450), file the guide bar rails to an even The guide bar must not cut at an angle. Any fault in this height.
  • Page 16 Maintenance Stack Cutter is easy to maintain. As 95% of the structure Changing the drive belt is protected against rust, it can stand in the cold. The drive belt between the motor and the guide bar However, extra maintenance is then required – parts fastening must be regularly changed.
  • Page 17 The degree of pre-assembly depends on the type Guide bars, chains, sprockets and other spare parts can of packing that is most suitable for your particular be ordered from LOGOSOL. See the article lists on the delivery. following pages. Labels are used to facilitate the assembly of some of the Order LOGOSOL’s product catalogue.

  • Page 19: Hexagonal Bolt

    Part no. Number Designation Information Article number Rear leg Pk-13 Rear leg corner profile Pk13-2 Hexagonal bolt M6S 933 M6x20 0000-200-0001 Round washer Brb 125A 6.4 Fzb 0000-800-0003 Beam Pk-15 Left guard Pk-18 Right guard Pk-18-1 Hexagonal bolt M6S 933 M6x20 0000-200-0001 Round washer Brb 125A 6.4 Fzb...
  • Page 20 Line threading...

  • Page 21: Spacer Sleeve

    Part no. Number Designation Information Article number Stand Pk-01-03 Cmpl. motor bracket Pk-02 Cmpl. motor unit Pk-09 Round washer Brb 125A 10.5 0000-800-0020 Locking nut 985 M10 FZB 0000-500-0007 Top plate Pk-17-5 Hexagonal bolt M6S 933 M10x30 FZB 0000-200-0027 Round washer Brb 10.5x22x2 Fzb 0000-800-0008 Locking nut...
  • Page 22 Part no. Number Designation Information Article number Motor bracket pk-02-04 Sledge strip, stack-cut pk-02-05 Slide strip, stack-cut Bolt R6B 7504 K B6x19 Fzb Hexagonal bolt M6x20, DIN 933 Washer Brb 6.4 Square nut M4M M6 Hexagonal bolt M10x45 Hexagonal nut Sheave Spacer sleeve 10/6/10 R-723-2505...
  • Page 23 Part no. Number Designation Information Article number Motor plate Pk-05 Motor plate lid Pk-05-01 Hexagonal bolt M6S 933 M6x20 Fzb 0000-200-0001 Round washer Brb 125A 6.4 Fzb 0000-800-0003 Cmpl. bearing housing with shaft Pk-04 Socket head cap bolt MC6S 912 M8x25 0000-100-0005 Round washer Brb 125A 8.4...
  • Page 24 Part no. Number Designation Information Article number Cover plate Pk-06-v2 Oil pump 9999-000-6020 Transp. oil hose 9999-000-6036 Nipple 9999-000-6018 Guide bar upper washer Pk-10-v3, pos 2 Socket head cap bolt MC6S M5x12 Locking nut 985 M5 0000-500-0009 Star-headed bolt M5x16 9999-000-6002...
  • Page 25 Part no. Number Designation Information Article number Bearing housing, stack-cut Pk-04-1 Chain tensioner bolt 501 79 27-01 Husqvarna Tensioning pin 501 22 68-01 Husqvarna Stop bolt T6SS DIN 915 M5x16 Shaft 700-2001 9999-000-6066 Pulley 15/40 700-3001-1 9999-000-6025 Ball-headed thrust bolt DIN 916 - M 8 x 10 Ball bearing 9999-000-6067...
  • Page 26 Part no. Number Designation Information Article number Guide bar tip control Pk-08-1 Threaded sleeve, Pop-nut M6 UFO 65 Hexagonal bolt M6S 933 M6x35 0000-200-0013 Round washer Brb 125A 6.4 0000-800-0003 Spacer sleeve 8/6/10 888-1020 4510-723-2511 Locking nut 985 M6 FZB 0000-500-0001...
  • Page 27 Adjusting guide bar alignment Schematic sketches of the machine’s sighting rod on the motor side and the saw unit seen from above. “ ”shows incorrect adjustment, “OK” shows correct adjustment. This symbol “ ” shows where to adjust. Adjusting the stand C.

  • Page 28: Circuit Diagram

    Circuit diagram Potentially lethal voltage! Faulty connection can result in a fatal accident. Note that only qualified electricians are authorised to open or work on the machine’s electrical equipment. Ensure that the power is disconnected before exposing any part of the electrical system. Connect the machine and check that the motor is running in the right direction.

  • Page 29: Technical Data

    EU declaration of conformity in accordance with Machinery Directive 98/37/EC, Annex II A. Manufacturer, LOGOSOL AB, Industrigatan 13, SE-871 53 Härnösand, tel. +46 (0)611 18285, hereby declares that Stack Cutter, art. no. 8540-000-0150 is manufactured in accordance with the following directives: Machinery Directive 98/37/EC, EMC Directive 89/336/EEC and the Low Voltage Directive 73/23/EEC.
  • Page 30 LOGOSOL LogTurner Perfect for rolling and turning logs. Easy on your back, boosts your muscles! Full log control even when changing grip LOGOSOL Sverige SE-871 33 Härnösand Fiskaregatan 2 Telefax 0611-182 89 Telefon 0611-182 85 www.logosol.se info@logosol.se...

This manual is also suitable for:

Stack cutter 15008540-000-0150

Table of Contents