1. Manuals
  2. Brands
  3. Logosol Manuals
  4. Cutter
  5. 0458-395-0603
  6. Manual

Logosol 0458-395-0603 Manual

Stack cutter pk 1500
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
BRUKSANVISNING
Ref. no. 0458-395-0603
LOGOSOL
STACK CUTTER PK 1500
EN

Advertisement

Table of Contents
loading

Related Manuals for Logosol 0458-395-0603

Summary of Contents for Logosol 0458-395-0603

  • Page 1 BRUKSANVISNING Ref. no. 0458-395-0603 LOGOSOL STACK CUTTER PK 1500...
  • Page 2 We are very pleased that you have demonstrated your confidence in us by purchasing this product, and we will do our utmost to meet your expectations. Logosol has been manufacturing products since 1989. In that time we have supplied approximately 50,000 machines to satisfied customers the world over.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Safety instructions Machine description Moving the Stack Cutter Setting up the Stack Cutter Components Assembly Adjustments Preparations Control panel Stack cutting End trimming Setting the cut length Changing cutting equipment Troubleshooting – cutting equipment Sharpening the chain Maintenance Material drying Exploded views...

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS • Read carefully through the entire user manual Key to symbols before starting to operate the machine. Failure For your own safety, read through the entire to observe these safety instructions may result in user manual carefully and do not start fatal injuries.
  • Page 5 The machine must not be modified or added to. Use that no unauthorised person can start the machine. only parts supplied by LOGOSOL. After servicing, the machine must be restored to its original condition. - After fitting a chain, ensure that it runs freely before plugging the cable into the control panel.

  • Page 6: Machine Description

    MACHINE DESCRIPTION Lifting eye Fixed guide bar guard Saw unit Belt drive Oil tank Motor bracket Handle bar Winding crank safety catch Guide rail Winding crank Sight Control panel Adjustable wheel Adjustable guide bar guard Sighting rod and holder Rear leg Lockable castor...

  • Page 7: Moving The Stack Cutter

    Connect the chip extractor hose and secure it with End trimming with Logosol’s Stack Cutter hose clamps both at the the machine end and at the Note where the operator is standing, the position extractor end.

  • Page 8: Components

    COMPONENTS 8200-005-0005 00-00000 Check that all components are included in the shipment when receiving the Stack 00-00000 Cutter. 00-00000 00-00000 00-00000 00-00000 Manual 00-00000 00-00000 00-00000 00-00000 00-00000 00-00000 00-00000 00-00000 00-00000 00-00000 00-00000 00-00000 00-00000 00-00000...
  • Page 9 PK1500 STACK CUTTER COMPONENTS – MOTOR BOX Motor kmpl 00-00000 BOLT BAG M6x120 M8x120 M8x60 M10x35 M10x30 M10x25 M6x20 M8x35 M8x20 M5x20 M5x8...

  • Page 10: Assembly

    PK-1500 BOLTS & NUTS Definition of fasteners. Shoulder bolt Allen bolt Phillips bolt Partial thread Allen bolt Hex bolt Slotted bolt Set screw Partial thread hex bolt Hex nut Flange bolt Flange nut Partial thread flange bolt Carriage bolt Flat washer ADDITIONAL SYMBOLS DIAMETER &...
  • Page 11 PK1500 STACK CUTTER PK-1500 M8x20 10 x M6x20 14 x...
  • Page 12 PK-1500 Tighten the bolt joints fingertight. M8x120 Note that the aluminium profile should be fitted such that it extend over the edge of the square tube. 10 x M6x20 10 x M8x120 12 x...
  • Page 13 PK1500 STACK CUTTER PK-1500...
  • Page 14 PK-1500 Place the motor bracket (raised by blocks) next to the front leg. Fit the guide rail to the motor bracket and then screw it to the front leg. Note that the holes in the guide rail (four holes in a row) should point down. Wait with the bolt joints for these holes, as these holes are to be used for attaching the left leg.
  • Page 15 PK1500 STACK CUTTER PK-1500 M6x120 16 x M10x25...
  • Page 16 PK-1500 M10x25 M10x30...
  • Page 17 PK1500 STACK CUTTER PK-1500 Fit the sighting rod to the centre of the rear leg. M8x120 M8x20 M8x60...
  • Page 18 PK-1500 12 x 12 x 12 x M6x120 12 x 24 x...
  • Page 19 PK1500 STACK CUTTER PK-1500 M8x20 M5x8 Fit the line pulleys and the line holders in the holes in the top plate, then thread the lifting line as in the illustration.
  • Page 20 PK-1500 M5x20...
  • Page 21 PK1500 STACK CUTTER PK-1500 Attach suitable bar nose guard. M6x20...
  • Page 22 PK-1500 M6x20 M6x20...
  • Page 23 PK1500 STACK CUTTER Good job! Go through all the adjustment steps to ensure proper operation of the machine.

  • Page 24: Adjustments

    ADJUSTMENTS Check that the inside of the frame is perpendicular.If that is not the case, use spacers between the moun- ting plate and the front leg until it is perpendicular. There is a slight play between the mounting plate and the rear leg, which you can use to adjust the frame.
  • Page 25 PK1500 STACK CUTTER ADJUSTMENTS Adjust the guide bar vertically using the adjusting bolts on the underside of the motor. Tighten the chain using the tensioning bolt on the bar mount. To be able to tighten the chain, you have to loosen the top plate fastening bolts.

  • Page 26: Preparations

    PREPARATIONS Ensure that the power to the machine is cut to take the kerf width into account. during the preparations. Exact measurements are made between each saw End trimming (F) refers to cutting off the stack cut (see “Setting cut length”). ends.

  • Page 27: Control Panel

    PK1500 STACK CUTTER CONTROL PANEL ELECTRICAL CONNECTION Do not connect the machine to a power supply before you have read and understood the entire manual. Incorrect use may result in fatal injuries. Risk of electric shock. Start The Stack Cutter must be connected via an earth- Emergency stop/stop leak circuit breaker.

  • Page 28: Stack Cutting

    The maximum permitted distance between the stack and the guide bar guard is 50 mm. Longer guide bar guards can be ordered from Logosol. Check the guide bar’s path and the ground beneath the guide bar, to ensure that you do not saw through anything unintentionally.

  • Page 29: End Trimming

    PK1500 STACK CUTTER MARKING UP FOR END TRIMMING The basic procedure when using the Stack Cutter is way that you can measure close to the centre of the to mark out the intended cut by drawing lines on stack. the sides of the timber stack. Draw a vertical line on both sides of the end of the stack that is to be 6.

  • Page 30: Setting The Cut Length

    SETTING THE CUT LENGTH End trimming Once one of the stack ends has been trimmed, the cut surface provides the point for measuring the position of the next cut. Set the measuring stick’s stop plate to the desired At the top and the bottom of both sides of the length.

  • Page 31: Changing Cutting Equipment

    Logosol. A new chain may need re-tightened after the first or 2. During fitting, lower the motor unit until it rests second cut.

  • Page 32: Troubleshooting - Cutting Equipment

    1. One cause of problem when using the Stack bar. We recommend Logosol’s high-performance Cutter is that you have a dull chain. vegetable chain oil for chain sawmills (SKU: 0718- 000-1010, 10 litres) 2.

  • Page 33: Sharpening The Chain

    PK1500 STACK CUTTER SHARPENING THE CHAIN The cutters on the chain of a motor saw are coated with a very thin layer of chromium. This gives a very sharp and durable edge. As long as the edge is in the chromium layer, your chain will have perfect sharpness.

  • Page 34: Maintenance

    MAINTENANCE If you keep your cutting equipment in good condition, the sawn product will have the right dimensions, you will cut faster and the the equipment will last longer. When the timber you are cutting is “aggressive” to the chain (e.g. dry wood, hard wood, or timber that has sand or dirt in the bark), regular sharpening of the chain is particularly important.

  • Page 35: Material Drying

    It is important to place the spacers that the logs still can be shaped when they are exactly over each other, to keep the boards from pressed against each other. warping or bending. LOGOSOL also has electric wood drying kilns for preparation of fine joinery timber.

  • Page 36: Exploded Views

    Part no. Quantity Designation Information Rear leg Pk-13 8510-001-0070 Rear leg corner profile Pk13-2 8510-001-0072 Hex bolt M6S 933 M6x20 9008-319-1349 Round washer Brb 125A 6,4 Fzb 9291-021-0140 Beam Pk-15 8510-001-0065 Left guard Pk-18 8510-001-0067 Right guard Pk-18-1 8510-001-0069 Hex bolt M6S 933 M6x20 9008-319-1349 Round washer...
  • Page 37 PK1500 STACK CUTTER New: Spacers between rear leg (1) and angle profile (2) for guide bars shorter than 150 mm.
  • Page 38 Part no. Quantity Designation Information Stand Pk-01-03 8520-300-0400 Cmpl. motor bracket Pk-02 8510-001-0190 Cmpl. motor unit Pk-09 8510-001-0400/0230 Round washer Brb 125A 10,5 9291-021-0200 Locking nut 985 M10 FZB 9214-320-1305 Top plate Pk-17-5 8510-001-0061 Hex bolt M6S 933 M10x30 FZB 9008-319-1830 Round washer Brb 10,5x22x2 Fzb...
  • Page 39 PK1500 STACK CUTTER Line threading...
  • Page 40 Part no. Quantity Designation Information Motor bracket pk-02-04 8510-001-0018 Carriage strip, stack cutter pk-02-05 9999-000-1030 Slide strip, stack-cutter 8510-001-0054 Bolt R6B 7504 K B6x19 Fzb 0000-900-0001 Hex bolt M6x20, DIN 933 9008-319-1949 Washer Brb 6,4 9291-021-0140 Square nut M4M M6 9222-068-0900 Hex bolt M10x45...
  • Page 41 PK1500 STACK CUTTER...
  • Page 42 Part no. Quantity Designation Information Motor plate Pk-05 8510-001-0028 Motor plate lid Pk-05-01 8510-001-0119 Hex bolt M6S 933 M6x20 Fzb 9008-319-1349 Round washer Brb 125A 6,4 Fzb 9291-021-0140 Cmpl. bearing housing with shaft Pk-04 8510-001-0035 Allen bolt MC6S 912 M8x25 9040-319-1850 Round washer Brb 125A 8,4...
  • Page 43 PK1500 STACK CUTTER Part no. Quantity Designation Information Cover plate Pk-06-v2 8510-001-0040 Oil pump 9999-000-6020 Transparent oil hose 9999-000-6036 Nipple 9999-000-6018 Guide bar upper washer Pk-10-v3, pos 2 8510-001-0236 Allen bolt MC6S M5x12 9045-319-0512 Locking nut 985 M5 9214-320-0700 Star-headed bolt M5x16 9999-000-6002...
  • Page 44 Part no. Quantity Designation Information Bearing housing, stack cutter Pk-04-1 8510-001-0042 Chain tensioner bolt 501 79 27-01 Husqvarna 8510-001-0047 Tensioning pin 501 22 68-01 Husqvarna 8510-001-0048 Stop bolt T6SS DIN 915 M5x16 8510-001-0048 Shaft 700-2001 9999-000-6066 Pulley 15/40 700-3001-1 9999-000-6025 Ball-headed thrust bolt DIN 916 - M 8 x 10 9210-260-1100...
  • Page 45 PK1500 STACK CUTTER Part no. Quantity Designation Information Bar nose guide Pk-08-1 8510-001-0125 Threaded sleeve, Pop nut M6 UFO 65 Hex bolt M6S 933 M6x35 9007-346-1380 Round washer Brb 125A 6,4 9291-021-0140 Spacer sleeve 8/6/10 888-1020 4510-723-2511 Locking nut 985 M6 FZB 9214-320-0900...

  • Page 46: Circuit Diagram

    CIRCUIT DIAGRAM Potentially lethal voltage! Faulty connection can result in a fatal injury. Note that only qualified electricians are authorised to open or work on the electrical equipment of the machine. Ensure that the power is cut before exposing any part of the electrical system. Connect the machine and check that the motor is running in the right direction.

  • Page 47: Technical Data

    PK1500 STACK CUTTER TECHNICAL DATA, STACK CUTTER 1200/1500 Dimensions Length 2600 mm Stack Cutter 150 Width 1100 mm Height 1900 mm Weight 145 kg Cutting dimensions Max. stack width 1400 mm Stack Cutter 150 Theoretical max. width approx. 1450 mm Max.

  • Page 48: Ce Declaration Of Conformity

    In accordance with Directive 2006/42/EG, Annex 2A Logosol AB Fiskaregatan 2 871 33 Härnösand, SWEDEN herewith declares that Logosol Stack Cutter has been manufactured in conformity with: Machinery Directive 2006/42/EG EMC Dierctive 2004/108/EU and has been manufactured in conformity with the...
  • Page 49 Fiskaregatan 2, S-871 33 Härnösand, SWEDEN Phone +46 611 18285 | info@logosol.com | www.logosol.com...

Table of Contents