Subscribe to Our Youtube Channel
Related Manuals for Belson Outdoors RPPB6F
Summary of Contents for Belson Outdoors RPPB6F
- Page 1 627 Amersale Drive Naperville, IL 60563 Phone: (800) 323-5664 Fax: (630) 897-0573 sales@belson.com Model # RPPB6F Instructions Sheet MODULAR PLANTER BENCH www.belson.com...
- Page 2 BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED. B - BULL NOSED BENCH BOARD ( 2 ) - TWO BULL NOSED BENCH BOARDS A - CENTER BENCH BOARD ( 4 ) - FOUR CENTER BENCH BOARDS FP FASTENER PACK ONE FASTENER PACK ( 1 ) - CENTER BENCH END ( 2 ) - BENCH ENDS...
- Page 3 BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED. 32 - #12 X 2-1/2" PAN HEAD PHILLIPS SCREW 4 - 3/8" X 4-1/4" HEX BOLT HEAD BOLT 8 - 3/8" FLAT WASHER 4 - 3/8" NYLON LOCK NUT ALSO NEEDED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS: 1 - #3 PHILLIPS DRIVE BIT 2 - 9/16"...
- Page 4 STEP #1: AS SHOWN IN THE DIAGRAM BELOW, PLACE ONE SIDE PANEL FACE DOWN ON A FLAT SURFACE. PLACE THE FRAME RINGS AT THE TOP AND BOTTOM SECTIONS OF THE PANEL, BEING SURE TO LINE UP THE PRE-DRILLED HOLES IN THE FRAME RINGS TO THE PRE-DRILLED PILOT HOLES IN THE SIDE PANEL.
- Page 5 #12 X 2-1/2” PAN HEAD PHILLIPS SCREW STEP #2: PLACE ANOTHER SIDE PANEL BESIDE THE PREVIOUS PANEL, SO THAT IT TOUCHES AS DISPLAYED IN THE DIAGRAM ABOVE. GENTLY TURN THE SIDE PANEL WITH THE RINGS INSTALLED ON TO THE NEW SIDE PANEL, MAKING SURE THE HOLES LINE UP WITH THE PRE-DRILLED PILOT HOLES IN THE NEW PANEL.
- Page 6 #12 X 2-1/2” PAN HEAD PHILLIPS SCREW STEP #3: REPEAT THE PREVIOUS STEP. www.belson.com...
- Page 7 STEP #4: PLACE THE BOTTOM PANEL INTO THE OPENING BETWEEN THE FRAME RINGS. www.belson.com...
- Page 8 #12 X 2-1/2” PAN HEAD #12 X 2-1/2” PAN HEAD PHILLIPS SCREW PHILLIPS SCREW STEP #5: REPEAT STEP 2. TURN THE PLANTER UPRIGHT ONTO ITS BASE. PLEASE USE CAUTION WHILE MOVING AS THE PLANTER WILL WEIGHT APPROXIMATELY 96 POUNDS. REPEAT STEPS #1-5 TO COMPLETE THE SECOND PLANTERS BOX. www.belson.com...
- Page 9 STEP #6: PLACE THE CENTER BENCH BOARDS ON A LEBEL SURFACE WITH THE PILOT HOLES FACING UP. ON EACH SIDE OF THE CENTER BENCH BOARDS, PLACE ( 1 ) ONE SIDE BENCH BOARD WITH THE PILOT HOLES CLOSEST TO THE CENTER BENCH BOARDS AND FACING UP. #12 X 2-1/2”...
- Page 10 #12 X 2-1/2” PAN HEAD PHILLIPS SCREW STEP #8: PLACE THE REMAINING BENCH END AND CENTER BENCH END IN POSITION AS SHOWN ABOVE, BEING SURE TO ALIGN THE PRE-DRILLED HOLES TO THE PILOT HOLES IN THE BENCH BOARDS. AFTER THE HOLES ARE PROPERLY ALIGNED, FASTEN WITH ( 1 ) ONE #12 X 2-1/2” FLAT HEAD PHILLIPS SCREW PER HOLE TO SECURE.
- Page 11 STEP #9: WITH BOTH PLANTER BOXES UPRIGHT, ALIGN THE PRE-DRILLED HOLES IN BENCH END, WITH PREDRILLED HOLES IN SIDE PANELS OF PLANTER BOX. USE ( 1 ) ONE 3/8” X 4” HEX BOLT HEAD BOLT, ( 2 ) 3/8” FLAT WASHER AND ( 1 ) ONE NYLON LOCK NUT PER HOLE TO SECURE. 3/8”...
Need help?
Do you have a question about the RPPB6F and is the answer not in the manual?
Questions and answers