Table of Contents
Advertisement
Quick Links
141-MX48
Power Feeder 230V
Operationg instructions
Distributor:
IGM nástroje a stroje s.r.o.
Ke Kopanině 560, 252 67, Tuchoměřice
Czech Republic, EU
Phone: +420 220 950 910
E-mail: sales@igmtools.com
Website: www.igmtools.com
PDF ONLINE
www.igmtools.info
2022-09-15
141-MX48 Power Feeder 230V Manual EN v1.1.00 A4ob
Advertisement
Table of Contents
Related Manuals for IGM 141-MX48
Summary of Contents for IGM 141-MX48
- Page 1 Power Feeder 230V Operationg instructions Distributor: IGM nástroje a stroje s.r.o. Ke Kopanině 560, 252 67, Tuchoměřice Czech Republic, EU Phone: +420 220 950 910 E-mail: sales@igmtools.com Website: www.igmtools.com PDF ONLINE www.igmtools.info 2022-09-15 141-MX48 Power Feeder 230V Manual EN v1.1.00 A4ob...
-
Page 2: Table Of Contents
Because of our policy of constant improvement, the design, construction or pictures may differ slightly. Should you discover any mistakes, please contact us at podpora@igm.cz. TABLE OF CONTENTS page... -
Page 3: Warranty Service
2. WARRANTY SERVICE The warranty is subject to Terms and Conditions and Any alterations or changes to the machine are Warranty Conditions of IGM nástroje a stroje s.r.o., prohibited. the current version of which are available at www. igmtools.com. -
Page 4: Risks
Operating instructions EN 4. SPECIFICATIONS OF THE MACHINE Never leave the machine unattended. Always switch 4.1 Machine description the machine off when leaving the workspace. Watch your fingers and other body parts when working. Never walk away from a machine without protective guards. -
Page 5: Transport, Unpacking And Assembly
Operating instructions EN 5. TRANSPORT, UNPACKING AND ASSEMBLY 2. Locate boring position 5.1 Transport and unpacking For your boring convenience and accuracy, a SCALE The machine is not assembled due to transport. 1:1 SELF-ADHESIVE DRILLING TEMPLATE is provided Remove the feeder from the packaging and place and enclosed in the package. - Page 6 Operating instructions EN Insert OVER-ARM into ELEVATING-BRACKET. Turn wheel a few turns. Tighten LEVER. Insert the extension tube (A) into cross slide vise, push (B) hand-wheel into cross slide vise and rotating while push-in, ensure the hand-wheel kit are intermeshing with extension tube kit properly. Lock the headless hex-screw in to cross slide vise (C), the rotating the handle-wheel and insert it into hand-wheel gear groove (D) to ensure the gears can...
-
Page 7: Operation Control
Operating instructions EN • Loosen two attached screws(C), and adjust the motor suspension angle (D). Confirmation: • Locked the hex-screw (A) and quick release handle grip (B) to even the gap of two end. Loosen the quick release lever to rotate the machine body. To complete the installation: Confirm all the handle and screws are locked properly. -
Page 8: Control- Joint
Operating instructions EN rotate side-wheel. (C) Over-Arm elevation: Loosen Lever (D), rotate TOP-Wheel. (E) NOTICE: The purpose of elevating kits tolerance gap is to allow smooth operation while elevating the feeder; Please pull back machine body to feed-in direction after elevating adjustment and lock the hand lever to tight at the meantime (A). - Page 9 Operating instructions EN Using the extension cable if needed: 30M or under Rated current reference: using 12AWG cable, 46M or above using 10AWG cable. Ensure all the grounding wires connected properly; impropriate connection may cause the damage to the motor. Ensure the groupding wire of the motor (green or yellow) connected techinician for any further assistance.
-
Page 10: Speed Control
Operating instructions EN 8. SPEED CONTROL Notice: cut out the power before adjustment Appropriate feeding speed rate and well sharped cutting blade can cause the procedure process quality and efficiency. Determinate the correct feeding speed by the hardness of the work-piece, material and the desired cutting procedure. -
Page 11: Roller Replacement
Operating instructions EN Gear replacement instruction. NOTE: The hub of the gear should be turned inward to Loosen two attached screws to take off the cover. avoided possible interference. NOTE: Optional gear set available 34/44/04/54 model speed(4+4=8) 38/48/68model speed(8+8=16) 9. Roller replacement Notice: cut off the power source before operation. -
Page 12: Feeder Operation Instruction
Operating instructions EN • (MOBILUX EP 2); Turbine oil filled up standard • (FUCHS RENOLIT EP 2); • (BP ENERGREASE MM-EP 2) • 38/48 300CC (38mm, 1-1/2“) • MX 200CC (38mm, 1-1/2“) Turbine oil: Exchange turibine oil first 200 hours of 30 day while Using wind gun to maintain the feeder after every first starts the machine. - Page 13 Operating instructions EN • Feeder position & guiding plate (pic. 11-2). • Feeding pressure & Work-piece (pic. 11-3). Manual operation • Rollers & cutting blade: Pic. 11-2 • Feeding pressure & Work-piece: • Feeder position & guiding plate (pic. 11-2) •...
-
Page 14: Assembly And Parts List
Operating instructions EN 12. MX48B HOUSING ASSEMBLY www.igmtools.com -14-... - Page 15 Operating instructions EN HEAVY-DUTY UNIVERSAL STAND ASSEMBLY www.igmtools.com -15-...
- Page 16 Wormgear Box Cover 114G-3 Q021701 Oil Seal 114G-4. S060616 Cap Screw RO121 RO121 Roller tire IGM nástroje a stroje s.r.o., Ke kopanině 560, Tuchoměřice, 252 67, Czech Republic, E.U. +420 220 950 910, www.igmtools.com © 2022 IGM nástroje a stroje s.r.o.