Advertisement
SYSTEM PROTECTION FEATURES
Nine Cycle Maximum
The controls will shut off for 15 minutes any time nine (9) full
•
retractions occur in less than 30 minutes.
When this occurs, all four-system status lights blink off and on.
•
This sequence can be overruled by turning the ignition off, then back on.
•
Low Voltage Protection
If the voltage falls below 11.5 VDC, leveler operation will cease
•
and the low voltage LED will flash.
Controls will be inoperable until battery voltage climbs above 13
•
VDC, at which time leveling functions will resume.
Front Too Low
• Should the angle of front of the RV drop below level the system
will stop the Landing Gear from retracting and possibly setting
the front of the RV on the ground.
Manual Override
• To Manually Extend or Retract Leveler, use a 1/2˝ socket on Drive
Nut on end of motor (
11).
FIG
Rotate nut counter clock-wise (looking from bottom end of nut
[
11) to extend leveler.
FIG
: It takes 500 revolutions of nut to extend/retract leveler 1˝.
NOTE
PERSONAL INJURY/PRODUCT DAMAGE
Battery operated drills, 9.6V to 18V, are powerful. Hold drill with both
•
hands to protect your wrist. Keep loose clothing and body parts away
from drill as the reaction torque from the drill may cause it to kick back.
Refer to your drill manufacturer's operation manual.
•
Do not over - extend or over - retract levelers. Each leveler has built - in
•
stops. Excessive force applied against the stops will cause damage.
When manually overriding the leveler do not use pneumatic tools to
•
operate any leveler. They can over-extend or over-retract the leveler.
If the motor will not extend/retract the leveler and the motor is making
•
a ratcheting sound (clutch slipping), do not use the manual override.
Immediately contact an Atwood Service Center and have leveler
replaced. Do not use the leveler until replaced.
EMERGENCY STOP ANY LEVELER ACTIVITY
PRESS ANY BUTTON ON KEY PAD
Unhooking From Tow Vehicle and Leveling RV
1.
2. Do not extend slideouts until RV is leveled.
3. Switch Activation Switch ON.
4. Turn on Key Pad
5. Auto extend Landing Gear
6. Set preferred King Pin height for
7. Detach Tow Vehicle from RV and
8. Auto extend rear levlers and level RV.
9. Once RV is level, turn unit off and
C A U T I O N : R E A D I N S T R U C T I O N M A N U A L 6 6 3 8 5 B E F O R E U S E
CAUTION
Park on solid ground without obstructions.
Chock wheel and warn persons to stand clear of RV.
(Front Legs)
unhooking hitch
move to safe distance.
Activation Switch OFF.
1. Internal parts of leveler are permanently lubricated at the factory
and do not require any further lubrication.
2. If it is not possible to get levelers to operate freely, replace
leveler.
Hooking Up To Tow Vehicle Retraction of Levelers
Retract slide rooms and
1.
warn all persons to stand clear of RV
2. Switch Activation Switch ON.
3. Turn on Key Pad
ON
4. Auto retract the rear levelers
5. Set King Pin height (per hitch mfg.'s
EXT/ALL/FRONT
recommendations) for proper
hitch connection
EXT/FRONT
6. Position tow vehicle, connect hitch
RET/FRONT
and connect trailer wiring harness
7. Auto retract Landing Gear (front legs)
once safely hitched.
AUTO
8. Turn unit off and Activation Switch OFF
ON
9. Remove chocks from wheels before towing.
3
MAINTENANCE
10/9/06 MPD 70335
ON
RET/ALL/REAR
EXT/FRONT
RET/FRONT
RET/ALL
FRONT
ON
Advertisement
