5. Maintenance and Management······························ 9 6. Product Nameplate··············································· 10 A. Warranty and Repair············································ 11 B. Certification Details·············································· 12 C. Smart Gas Sniffer Manual··································· 13 D. How to Calibrate Gas Density····························· 21 E. Self-Diagnosis Error Code··································· 28 Smart Gas Detector / S2B-300...
2) Type of protection: “ia” - intrinsic safety 3) Gas group: Acetylene, Hydrogen, Carbon Disulfide 4) Temperature classification: Ignition temperature of gas or vapor > 135 ℃ 5) Equipment protection level n KCs (21-GA2BO-0393X) n KC (R-R-N54-S2B) Smart Gas Detector / S2B-300...
4.2. Standby Mode w Right after the power is on, S2B-300 operates in Stand-by mode. w In the standby mode, S2B-300 does not operate as a gas detector and performs internal error diagnosis and sensor stabilization. w When stabilization is over, the standby mode automatically exits and S2B-300 enters the detection mode.
Page 8
0 loction or a placte where possessing smart-phone is not permitted. However, the product operates independently without smart-phone and alert an alarm when a warning situation occurs. Smart Gas Detector / S2B-300...
6. Product Name Plate Product Nameplate § Nameplate of this product is attached on the back of the product as shown below. Smart Gas Detector / S2B-300...
NDTUM-S2B-EN REV1.0 A. Warranty and Repair A manufacturer, NodeTalks Corp., guarantees the quality of Smart Safety Ball, for 1 year from the date of shipment after product purchase. This means that there is no problem in the function and components of the products if the customers uses the products normally by complying with the precautions indicated in the user’s manual and that free A/S...
B. Certification Details Our smart gas detector, Smart Safety Ball (S2B-300), has obtained explosion-proof certification for intrinsic safety and complies with the following standards. IEC 60079-0:2017 IEC 60079-11:2011 KS C IEC 60079-0:2019 KS C IEC 60079-11:2020 • KCs (21-GA2BO-0393X) • KC (R-R-N54-S2B) Ex ia IIC T4 Ta: −20 ~ 50℃...
Page 14
After entering the verification number received, press the “Confirm Verification” button and then basic preparation for agreement of terms and conditions and the app use is completed. Smart Gas Detector / S2B-300...
Page 16
The volume of media sound is changed to the maximum whenever the app is launched that user identify alarm even poor surroundings(Figure on the bottom right). (the volume can be freely adjusted after running the app). Smart Gas Detector / S2B-300...
Page 18
19). You can temporarily turn off the time-weighted average exposure alarm for 60 seconds using the button on the lower left in the dedicated app, but alarm of Smart Safety Ball is not released before it leaves the gas leakage area. Smart Gas Detector / S2B-300...
Page 22
Span calibration should be performed at least every 6 months for accurate detection results. Separate test gas is required for span calibration. w Contact NodeTalks Corp.. if any problem occurs during calibration. ※ User Precautions for Calibration i. It is recommended to calibrate the gas concentration in a room temperature.
Page 24
Accordingly, after setting the dedicated app first in the process of preparing the gas concentration calibration as mentioned above, it is recommended to prepare for calibration in the order of starting Smart Safety Ball again. Smart Gas Detector / S2B-300...
Page 26
Calibrate button after selecting AUTO. concentration of test gas used for calibration is set as shown in the following table. Type of Gas Concentration 100 ppm 25 ppm Smart Gas Detector / S2B-300...
Page 27
NDTUM-S2B-EN REV1.0 Cautions w In case of span calibration, connect the regulator of standard gas cylinder and Smart Safety Ball using the adaptor and tube for calibration separately provided. Contact NodeTalks Corp., for details. w It recommended calibrate concentration room temperature.
Hydrogen sulfide(H sensor related errors - If self-diagnosis error occurs, turn off the device and turn int on again. - If the problem persists, contact NodeTalks Corp. E-mail: office@nodetalks.co.kr Website: www.nodetalks.co.kr Smart Gas Detector / S2B-300...