Wall Mounting; Operation; Installing And Removing The Battery Pack - Craftsman CMCE600 Instruction Manual

V20 max cordless caulk and adhesive dispenser
Table of Contents


Available languages

Available languages

Wall Mounting

Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
nOTE: Do not attempt to mount CMCB101 charger under a
bench or table.
nOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward the ceiling.

WARNING: Do not charge batteries while charger is
hung on Trackwall.
CRAFTSMAN chargers, except the CMCB101, can be
stored on CRAFTSMAN VersaTrack™ Trackwall. Hooks and
accessories are sold separately. Please refer to the VersaTrack™
Trackwall accessory sheet for further information.
nOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwall compatible.


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.

Installing and Removing the Battery Pack

(Fig. E)

WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack 
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery release button 
pack out of the tool handle. Insert it into the charger as
described in the charger section of this manual.
into the tool handle, align
and firmly pull the battery
Proper Hand Position (Fig. H)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
as shown in Fig H.
Variable Speed Dial (Fig. G)
The material's rate of flow is controlled by the
variable speed dial
to accomodate various applications.
Pick a speed by turning the dial to the desired setting.
nOTE: '1' is the lowest (slowest) setting and '6' is the
highest (fastest) setting.
Trigger Switch (Fig. H)
1. Squeeze the trigger switch
2. Release the trigger switch to turn the tool off.
Trigger Switch Lock-off (Fig. A, H)
Your tool is equipped with a trigger switch lock-off
safeguard against inadvertent release of material.
1. To lock the trigger switch, push trigger switch lock-off 
up. The tool will not operate with the switch in the
locked position.
2. To unlock the trigger switch, push the trigger switch
lock-off down.
Rotating Cartridge Holder (Fig. I)
The cartridge holder
rotates 360˚ to apply material at
any angle.
Plunger Rod Handle (Fig. A)

WARNING: To reduce the risk of serious personal
injury, DO NOT use the plunger rod handle as a hook
to suspend objects from.
The plunger rod handle
a stable location when not in use or for storage.
To Adjust Plunger Rod (Fig. A)
1. To manually adjust plunger rod
rod handle
to desirable position.
To Insert Material
Cartridge Holder (Fig. A, H, I, K)
nOTE: Material left in the cartridge holder may dry if left
unattended. Follow manufacturer's recommendations when
using caulk or adhesive material.
1. Ensure that plunger used is appropriate to material.
nOTE: Using incorrect plunger may result in material
container exploding during use, damaging cartridge
holder and/or caulk gun.
2. Use the trigger switch lock-off
3. Trim nozzle end of the caulk/material tube.
nOTE: Small nozzle openings require more force to push
the material, possibly affecting battery life.
to turn the tool on.
may be used to suspend tool from
, push or pull plunger
to lock trigger switch 


Table of Contents

This manual is also suitable for:


Table of Contents