Advertisement
Axial Air Mover Operation
Operating Instructions
The V
VP3000 A
A
IKING
XIAL
be put into service. Inspect the unit completely for any
shipping damage. Place the unit on the ground. Orient the
unit so the desired air flow direction is the same as the
indicator in the FOCUS Technology corner on the interior of
the unit. Plug the unit into a grounded outlet and select the
drying mode.
VP3000 A
A
XIAL
IR
Operator Panel Features
3-Position Drying Selector Switch
A 3-position drying mode selector switch is used to select
the V
VP3000 A
A
IKING
XIAL
three modes of operation are OFF, LOW or HIGH.
OFF - The VP3000 A
XIAL
LOW - The VP3000 A
XIAL
mode. This mode provides rapid drying and very quiet
operation.
HIGH - The VP3000 A
XIAL
mode. This mode provides rapid drying and low noise,
quiet operation.
Maintaining Your Axial Air Mover
W W A A R R N N I I N N G G : : D D i i s s c c o o n n n n e e c c t t t t h h e e u u n n i i t t f f r r o o m m p p o o w w e e r r b b e e f f o o r r e e s s e e r r v v i i c c - -
i i n n g g , , l l u u b b r r i i c c a a t t i i o o n n o o r r c c l l e e a a n n i i n n g g . . R R e e p p l l a a c c e e t t h h e e w w i i r r e e s s a a f f e e t t y y g g r r i i l l l l
a a f f t t e e r r s s e e r r v v i i c c i i n n g g , , l l u u b b r r i i c c a a t t i i o o n n o o r r c c l l e e a a n n i i n n g g . .
Servicing
Before each use, the V
IKING
be inspected for damage, blocked inlet or outlet, or any
excess buildup of foreign material.
When the V
VP3000 A
IKING
check for excessive vibration. If the unit vibrates exces-
sively or if blade rubs on housing turn off the unit immedi-
ately. Have a service technician inspect the unit to locate
the problem.
Motor Lubrication
Oil the unit every six months with 3 - 4 drops of SAE 20
weight non-detergent oil. Lubricate the motor with a drop
of oil after each washing.
4
M
as packaged is ready to
IR
OVER
M
OVER
M
'
mode of operation. The
IR
OVER
S
A
M
is not drying.
IR
OVER
A
M
is in "Normal" Drying
IR
OVER
A
M
is in "Ultra" drying
IR
OVER
VP3000 A
A
M
XIAL
IR
OVER
A
M
is first turned on,
XIAL
IR
OVER
IMPORTANT: The approved oil for lubrication is SAE 20
weight non-detergent oil, specifically designated for
use with electric motors.
Oil hole locations. Access the oil holes by removing the
protective grill(s) and turning the unit upside down. If user
adds oil, it is recommended to run unit for 5-15 minutes,
to remove excess oil from unit.
Cleaning The VP3000 Axial Air Mover
The V
VP3000 A
IKING
durable and washable polyethylene. When cleaning, the
use of solvents is NOT recommended.
When washing inside the unit, disconnect the unit from
its power source. Clean inner barrel, grills and blade. Wipe
down motor exterior with a damp cloth. If the motor gets
wet during cleaning, simply allow ample time for motor to
dry out completely before restarting. If you clean your
device frequently perform motor lubrication more frequently
as well.
If you wash the V
plan to use it within 24 hours, allow the fan to drip dry for
10 minutes and then run the V
for 3 - 5 minutes before storing it.
should
Replacement Parts and Optional Accessories
Contact the factory at 1-800-533-7533 to order replace-
ment parts, or optional accessories
4025204
4025206
4025207
4025460
4025299
V
VP3000 A
A
IKING
XIAL
A
M
'
housing is made of a
XIAL
IR
OVER
S
VP3000 A
A
IKING
XIAL
IR
VP3000 A
IKING
Switch, Rocker, On-Off-On
Grill, Safety, Intake
Grill, Safety, Exhaust
Axial Air Mover Stand
Stand Hardware Kit
M
with FOCUS
Technology Owners Manual
™
IR
OVER
M
and do not
OVER
A
M
XIAL
IR
OVER
Advertisement
