Subscribe to Our Youtube Channel
Related Manuals for Heritage Glastonbury SGSIN05
Summary of Contents for Heritage Glastonbury SGSIN05
- Page 1 Installation Guide Models Covered: Sequential and Concentric Exposed Shower Valves Please keep this booklet for future reference. Installer: When you have read these instructions, please ensure you leave them with the user.
-
Page 2: Table Of Contents
I N T R O D U C T I O N Thank you for buying a Heritage Product. When you buy a Heritage product, you can be confident that it not only features a beautiful, distinctive, classic design, but that it has also been made to the very highest quality standards. -
Page 3: Safety Notes
S A F E T Y N O T E S Please make sure you read these instructions and retain for future use. All products manufactured by Heritage Bathrooms are safe, providing they are installed and used correctly and also receive maintenance when needed. -
Page 4: Specification
Health Care Commercial These showers are designed to be used in conjunction with Heritage shower kits. We cannot guarantee compatability or adequate performance when used with other kits. This would also invalidate your guarantee. Please refer to the installation manual supplied with your Heritage... -
Page 5: Installation Requirements
I N S TA L L AT I O N R E Q U I R E M E N T S Important: If you install this shower This shower valve must be installed in compliance with current water regulations. If you have any valve with a gravity fed system, there must be doubts about the water regulation requirements a minimum head (vertical distance) from the... - Page 6 I N S TA L L AT I O N R E Q U I R E M E N T S Instantaneous Water Heater Unvented System cold mains supply cold mains supply Pumped System Pumped System (with Essex flange) 1m min.
- Page 7 I N S TA L L AT I O N R E Q U I R E M E N T S This fitting needs to be installed in accordance Size of tap or Vertical distance with the following Installation Requirements combination fitting of outlet above and Notes (IRN) to ensure they meet the...
-
Page 8: Prior To Installation
P R I O R T O I N S TA L L AT I O N Two 8 litre per minute flow regulators have been pre-fitted to this product for water efficiency. If you have low water pressure, or certain water supply systems these may need to be removed in order to achieve adequate flow. - Page 9 P R I O R T O I N S TA L L AT I O N To Remove/Replace: 1. Unscrew both inlet elbows anti-clockwise from the valve body. Flow Regulator 2. Remove the flow regulators using long-nosed pliers. 3. Screw the inlet elbows clockwise to fit back into the valve body.
-
Page 10: Tools Required
T O O L S R E Q U I R E D Cross Head Adjustable Pipe Cutter Drill Spanner Screwdriver 30mm Electronic 2.5mm & 10mm Pencil Safety Goggles Socket Spanner Detector Hexagonal Keys I N S TA L L AT I O N 1. -
Page 11: Installation
I N S TA L L AT I O N 5. Drill the fixing holes using a suitable drill bit. A pilot drill will be required if drilling into tiles. Insert the wall plugs and screw the backplate to the wall. Warning: Please check for any hidden pipes and cables before drilling holes into the wall. -
Page 12: Maintenance
M A I N T E N A N C E Replace/Clean Cartridge: Sequential Shower Valves: Undo the grub screw to remove the handle. Use a 30mm socket spanner to unscrew the cartridge from the valve body. Carefully remove the cartridge and spring. IMPORTANT Isolate the water supply... - Page 13 M A I N T E N A N C E Replace/Clean Cartridge: Undo the grub screw to Concentric Shower Valves: remove the flow handle. Use a 30mm socket spanner to unscrew the Undo the indice housng and cartridge from unscrew the screw to remove the the valve body.
- Page 14 M A I N T E N A N C E Maximum Temperature Setting: Sequential Shower Valves: The shower has been pre-set to 41°C. This is based on being fitted with nominally balanced pressures with the hot water inlet supply at 65°C. If your operating conditions are different to the above your maximum outlet temperature may differ.
- Page 15 M A I N T E N A N C E Maximum Temperature Setting: Concentric Shower Valves: The shower has been pre-set to 41°C. This is based on being fitted with nominally balanced pressures with the hot water inlet supply at 65°C. If your operating conditions are different to the above your maximum outlet temperature may differ.
- Page 16 M A I N T E N A N C E Servicing the Elbows: Remove the filters from both elbows and set aside. Unscrew the elbows Disconnect your shower kit. completely from the shower valve. Undo the compression nuts and grub screws at the bottom of the shower valve to remove from the wall.
- Page 17 M A I N T E N A N C E Check all components for damage and replace if necessary. Rinse thoroughly in clean water to remove any debris. Reverse the steps to re-fit the elbows and secure the shower to the wall.
-
Page 18: Troubleshooting
T R O U B L E S H O O T I N G Symptom Cause Remedy Partially closed isolation valve. Open isolation valve. Instantaneous water heater cycles on and off Increase water flow rate or as flow rate or pressure is too low. pressure through system. -
Page 19: Caring For Your Product
N E E D H E L P ? In the unlikely event that you encounter a problem with your Heritage product, you must, in the first instance, contact the retailer you purchased it from. They will advise as to whether it is due to a manufacturing fault or an installation fault. - Page 20 If you have any queries, our dedicated customer service teams and products experts are available to help. www.heritagebathrooms.com enquire@heritagebathrooms.com 0330 026 8503 Website Email us Call us UK: Heritage Bathrooms, Pooley Hall Drive, Birch Coppice Business Park, Dordon, Tamworth B78 1SG EU: Masco Europe S.à.r.l., 14 Rue Strachen, 6933 Mensdorf, Luxembourg.
Need help?
Do you have a question about the Glastonbury SGSIN05 and is the answer not in the manual?
Questions and answers