Cellularline Aries - Wireless Stereo Bluetooth Earbuds Manual

DESCRIPTION

1. MF (multifunction) button
2. LED
3. Charging Case charging LED
4. Charging Case residual charge LED
5. MicroUSB charging port
6. MicroUSB charging cable

PRELIMINARY OPERATIONS

Charging Case Charge: Charging Case has an internal battery which allows the earbuds to be recharged without being plugged in to a mains charger. The Charging Case must therefore be charged before recharging the batteries of the devices.

Connect the charging cable (6) to any USB port and connect the other end to the MicroUSB charging port (5); the red LED (3) will flash and turn off when recharging is complete.

Once you have finished recharging, disconnect the Charging Case from the power supply.

Charging Case battery indicator: refer to the flashing LED (3) while recharging the Charging Case:

• When the LED flashes red once every two seconds, from 1% to 25% charge
• When the LED flashes red twice every two seconds, from 25% to 50% charge
• When the LED flashes red three times every two seconds, from 50% to 75% charge
• When the LED flashes red four times every two seconds, from 75% to 100% charge.

The LED (3) will show a steady red light when recharging is completed (100%).

Recharging the earbuds: insert the devices in their respective docks and close the Charging Case flap, charging will start automatically. The red LED (2) turns on when charging is in progress. The LED (2) turns off when charging is complete.

Phone connection: before connecting ARIES to the phone, it is necessary to establish a connection between the two earbuds. Remove the individual earbuds from the charging dock. The LEDs (2) will begin to flash white. The earbuds will connect within a few seconds.

Once the connection has been established, the LED (2) on one of the earbuds will flash white/red in alternating fashion, indicating that pairing mode is active. Turn on Bluetooth® on your phone to run a search for devices and select ARIES when it is detected.

USING THE DEVICE IN STEREO MODE

Turning the unit on: remove the earbuds from the Charging Case or hold down the MF buttons of both devices for about 2 seconds.

Turning the unit off: put the earbuds inside the Charging Case or hold down the MF buttons of both devices for about 2 seconds.

To answer a call: you can answer calls from both earbuds by pressing the MF button (1). If both earbuds are inside the Charging Case when there is an incoming call, take out the right or left earbud, wait for the connection and then answer by pressing the MF button.

To answer a call: you can answer calls from both earbuds by pressing the MF button (1).

If both earbuds are inside the Charging Case when there is an incoming call, take out the right or left earbud, wait for the connection and then answer by pressing the MF button.

To end a call: you can end calls from both earbuds by pressing the MF button (1).

Play/Pause: press the MF button (1) of one of the two earbuds once.

Voice assistant: press the MF button (1) on the right earbud twice.

FF: press the MF button (1) of the right earbud for about 2 seconds to fast forward to the next track.

Rew: press the MF button (1) of the left earbud for about 2 seconds to rewind to the previous track.

Volume control: use the phone's volume buttons to adjust the volume of the earbuds.

Device flat battery indicator: if the LED flashes red, the battery is flat.

Charging Case flat battery indicator: When the Charging Case charge is below 25% the white LED (4) will flash quickly.

RESET: if the device does not work properly, it is possible to carry out a reset to restore factory settings.

• delete all previous pairings from the Bluetooth^® menu of the phone and reboot it.
• hold down the button of the earbud not working and slowly place it inside the Charging Case. Release the button only after the contacts of the earbud and those of the Charging Case have touched; the LED (4) of the Charging Case will flash white.
• put also the other earbud inside the Charging Case and close the cover.

Pair again. Remove the earbuds from the case. Both LEDs will flash white, then one of the two will start to flash red and white in alternating fashion. Turn on Bluetooth^® on the phone and select ARIES after it has been detected.

HEADSET TECHNICAL SPECIFICATIONS

Bluetooth^®: v5

Supported profiles: Headset – handsfree – A2DP / AVRCP

Range: 10m

Bluetooth^® Frequency Range: 20HZ -20000HZ

Battery voltage: 3.7V

Battery capacity: 30mAh X 2

Charging Case battery capacity: 300mAh / 1.11Wh

Micro-USB port voltage (V): 5V

Micro-USB port current (A): 500 mAh

Output Power: 3W x 2

Stand-by Time: 60 hours

Talk Time: 1.5 hours

Play Time: 7.5 hours

Charging the earbuds: approx. 1.5 hours

Charging Case Charge: approx. 1.5 hrs

Weight: 48g