TABLE OF CONTENTS SERVICE SAFETY PRECAUTIONS ............................ 3 HANDLING THE LCD MODULE ............................5 SERVICE MODE .................................. 7 LOCATION OF CONTROLS ............................... 12 LAYOUT OF MAJOR BOARDS ............................14 MECHANICAL DISASSEMBLY ............................15 EXPLODED VIEWS ................................17 PACKING DISASSEMBLY ..............................19 CHASSIS AND CABINET REPLACEMENT PARTS LIST ....................
SERVICE SAFETY PRECAUTIONS • The caution items shown here describe major safety issues and should always be observed. • The meanings of the various indications are as follows. Indicates a hypothetical situation in which service personnel and nearby third parties, or even WARNING end users due to a product defect after the service operation is completed, could possibly be in danger of injury or even death in the event of operational error.
Page 4
WARNING • Always advise users to keep children away. There is danger of injury to children from tools, disassembled products, etc. KEEP CHILDREN AWAY • Always disconnect the power plug before starting work whenever power is not required. Failure to disconnect the power plug before starting work can result in electrical shock. UNPULUG •...
HANDLING THE LCD MODULE Safety Precautions 3. If the panel surface becomes soiled, wipe with cotton or a In the event that the screen is damaged or the liquid crystal soft cloth. If this does not remove the soiling, breathe on (fluid) leaks, do not breathe in or drink this fluid.
Page 6
7. Do not expose the LCD module to direct sunlight or strong ultraviolet rays for an extended period of time. 8. Do not store the LCD module below the temperature con- ditions described in the specifications. Failure to do so could result in freezing of the liquid crystal due to cold air or loss of resilience or other damage.
SERVICE MODE 1. ENTERING SERVICE MODE 1) Press button once on 2) Press button again and 3) While pressing the button, Remote Control. keep pressing. press MENU button on TV set. or Sound Mute (Service mode display) DISPLAYING THE ADJUSTMENT MENU 1) Press MENU button on TV.
Page 8
4. SELECTING THE ADJUSTING ITEMS 1) Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) 5. ADJUSTING THE DATA 1) Pressing of VOLUME ; +/– button will change the value of data in the range from 00H to FFH. The variable range depends on the adjusting item.
Page 9
SELF DIAGNOSTIC FUNCTION 1) Press “9” button on Remote Control during display of adjustment menu in the service mode. The diagnosis will begin to check if interface among IC’s is executed properly. 2) During diagnosis, the following displays are shown. Firmware : Version information of microprocessor In case of file name : WL58_EU and Version : 0100 indicates[WL58_EU_0100].
Page 10
VERSION CHECK MODE 1) Press “9” button twice on Remote Control during display of adjustment menu in the service mode. The version of main MPU will begin to check. 2) During Version Check, the following displays are shown. MAIN MPU : Version information of microprocessor In case of file name : WL58_EU, Version 0100 for Code Program Version and (E16) for OSD Version indicates [WL58_EU_0100(E16)]...
Page 11
10. STATUS CHECK MODE 1) Press “9” button thrice on Remote Control during display of adjustment menu in the service mode. The status of this model will begin to check. 2) During Status Check, the following displays are shown. EXT1 1080i-50 C6 38 54 CE 08 0000 0000 0000...
LOCATION OF CONTROLS Front Standby INPUT 5 (EXT5) RED – Power On GREEN – On-timer set Back SCART 1 (EXT1) SCART 2 (EXT2) SCART 3 (EXT3) CABLE HOLDER FIXING STRAP HDMI INPUT SOCKETS decoder* M E DIA R E C . IN/OUT S AT media recorder...
Page 13
OK to confirm your selection Text control buttons Stereo/Bilingual reception Bass Boost/Super Woofer To select mode To mute the sound When using a TOSHIBA VCR or DVD: When in TV mode: Time display press to PAUSE When in Text mode:...
LAYOUT OF MAJOR BOARDS U003B FRONT AV BOARD U003E PC HDMI BOARD U003A TN AV BOARD U004 LOW B BOARD U003D KEY BOARD U001 U002A SIGNAL BOARD POWER BOARD U003C U002B RMT LED BOARD AC IN BOARD – 14 –...
CHASSIS AND CABINET REPLACEMENT PARTS LIST WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SERVICE SAFETY PRECAUTIONS" ON PAGE 3 OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 21
Location Parts No. Description Location Parts No. Description C873 76073189 ELECTROLYTIC, 35V 1000UF M CC79 76109102 CERAMIC CHIP, 50V B 1000PF K C876 76073204 ELECTROLYTIC CE04P 50V 330UF M 3A CC82 76109102 CERAMIC CHIP, 50V B 1000PF K C877 76669229 ELECTROLYTIC, 50V 2.2UF M CE10 76666470 ELECTORLYTIC, 16V 47UF M 3A C878...
Page 22
Location Parts No. Description Location Parts No. Description CV16 76092731 CERAMIC CHIP, 16V B 1UF K R672 76011472 CHIP, 1/20W 4.7K OHM J CV17 76092731 CERAMIC CHIP, 16V B 1UF K R673 76011182 CHIP, 1/20W 1.8K OHM J CV18 76100104 CERAMIC CHIP, 25V F 0.1UF Z R675 76011102 CHIP, 1/20W 1K OHM J CV19...
Page 33
FRONT AV BOARD PD2172A2 (U003B) FRONT AV BOARD PD2172A2 (U003B) BOTTOM (FOIL) SIDE TOP (COMPONENT) SIDE PV61 PV60 P661 GR602 GR601 RV122 RC11 RC12 RC11 PV60 PV61 RV121 RV121 RV129 RV122 RC12 R687 GR605 RV123 P661 R698 R687 CV122 CY650 DV120 23547833 R689...
Page 34
AC IN BOARD PD2171A2 (U002B) BOTTOM (FOIL) SIDE GAP3 GAP4 GAP1 GAP2 GAP6 GAP5 P801A P802A T801 T802 ????? 23547832 CAUTION E-568 LIVE AREA F801 T6.3AH 250V IS-P C3A PC HDMI BOARD PD2172A5 (U003E) PC HDMI BOARD PD2172A5 (U003E) BOTTOM (FOIL) SIDE TOP (COMPONENT) SIDE 23547833 R-1786...
Page 36
SIGNAL BOARD PD2238A1 (U001) SIGNAL BOARD PD2238A1 (U001) BOTTOM (FOIL) SIDE TOP (COMPONENT) SIDE – 41 – – 42 –...
Page 37
SCHEMATIC DIAGRAM MODEL : 37WL58P WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SERVICE SAFETY PRECAUTIONS" ON PAGE 3 OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 39
CIRCUIT BLOCK DIAGRAM TN-AV UNIT H001 VIDEO SYSTEM SIGNAL UNIT QV01 Q501 MM1630AQ TB1274AFG SYNC-DET DDR SDRAM DDR SDRAM CVBS SYNC-DET CORTEZ CVBS SCART-1 CVBS/S #8DET OUT-1 DATA CVBS PROCESS SCART-2 OUT-2 #8DET CVBS/S SCART-3 SCART-3 #8DET OUT-3 SEL-OUT ANALOG FRONT EXT-4 YCbCr...
Page 43
SCHEMATIC DIAGRAM MODEL : 37WL58P WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SERVICE SAFETY PRECAUTIONS" ON PAGE 3 OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
CIRCUIT BLOCK DIAGRAM TN-AV UNIT H001 VIDEO SYSTEM SIGNAL UNIT Q501 QV01 MM1630AQ TB1274AFG SYNC-DET DDR SDRAM DDR SDRAM CVBS SYNC-DET CORTEZ CVBS SCART-1 CVBS/S #8DET OUT-1 DATA CVBS PROCESS SCART-2 OUT-2 #8DET CVBS/S SCART-3 SCART-3 #8DET OUT-3 ANALOG SEL-OUT FRONT EXT-4 YCbCr...
Page 61
GR612 GR112 GR613 GR113 H001 OPEN OPEN OPEN OPEN ENG37A13GF euro tuner_GND tuner_GND TIF Type : Horizontal ANT IN TUNER-GND TUNER-GND 5V3TN Q102 R112 OPEN OPEN C114 C110 C111 C101 23367329 C119 OPEN OPEN OPEN B25V0.01 R115 OPEN R111 C112 OPEN PK01 OPEN...
Page 88
SH400 - Note: For GATE of IC705 During, POD STANDBY mode of GATE_BTXD line, it keeping at SW1.8V mode. Normally, when power is ON, POWER_DB line (L:ON) is shut-off whichever pin No.1 or 2 of IC 707 is OFF. 37WL58P SIGNAL SH.NO.
Page 89
37WL58P SIGNAL SH.NO. OCM MEMORY I/F (43/65)
Page 90
37WL58P SIGNAL SH.NO. FLASH MEMORY (44/65)
Page 93
Note: Normally, I2C Bus Lines (SDA_STBY, SCL_STBY), these are connected to Cortez line. When I2C Bus Lines are POD STBY mode, these are connected to DB line. 37WL58P SH.NO. SIGNAL STD-BY MICRO (47/65)
Page 94
37WL58P SIGNAL SH.NO. CORTEZ REG 1 (48/65)
Page 95
37WL58P SIGNAL SH.NO. CORTEZ REG 2 (49/65)
Page 96
37WL58P SIGNAL SH.NO. CORTEZ REG 3 (50/65)
Page 98
Tool Side 37WL58P SIGNAL SH.NO. SERVICE CONNECTOR (52/65)
Page 99
Note: I2C Bus lines switching for Stand-by Micom. SW1.8V to H (normally): Connect to Cortez SW1.8V to L (POD STBY mode): Connect to DB] 37WL58P SIGNAL SH.NO. I2C Switch (53/65)
Page 100
37WL58P SIGNAL SH.NO. AUDIO (1/2) (54/65)
Page 101
37WL58P SIGNAL SH.NO. AUDIO (2/2) (55/65)