Subscribe to Our Youtube Channel
Related Manuals for JETWAY FDF13 Series
Summary of Contents for JETWAY FDF13 Series
- Page 1 Quick Installation Manual NO: G03-FD_MF13QIG-F Rev: 1.0 Release date: 2022-07-14 Notice: The photos in this file are for illustration purpose only. The model may not be the latest version. Please refer to the product you purchased for actual specification.
- Page 2 I/O Outlets...
- Page 3 Dimension and Outlines I. To Dissemble the Chassis 1. Locate the screws at the spots marked on this side of the system and unscrew them one by one.
- Page 4 2. Remove the marked screw on the front IO panel. 3. Remove the marked screw on the rear IO panel. 4. Lift the cover up to open the chassis. 5. The overview of the internal structure of the system with HDD tray pre-installed.
- Page 5 6. Remove the marked screws to dissemble the HDD tray from the system. 7. The overview of the internal structure of the system.
- Page 6 II. To Install SO-DIMM to the board 1. Locate the SO-DIMM slot on the board. 2. Insert the gold-finger side of the compatible SO-DIMM into the slot at a 30 degree angle. See to it that the break of the module fit into the notch of the slot and the golden-finger side should be fully plugged into the slot.
- Page 7 III. To Install M.2 M-Key SATA (2242/2280) card 2280 2242 1. Locate the M.2 SATA slot on the board. System supports two types of M.2 M-Key card in different lengths (2242/2280). Prepare compatible M.2 SATA card. 2. To install compatible card, please remove the screw in the marked spot at first. 3.
- Page 8 4. Tighten up the screw removed before to the marked spot to secure the card. *Note: The screw post and nut are fixed at location MH4 by default for 8cm type-2280 card installation. If you wish to install type-2242 card, please remove corresponding screw post under the screw as well and lock the screw post into location MH2 before installing 4.2 cm card to the slot.
- Page 9 3. Insert the gold-finger side of the compatible card into the slot and press down. See to it that the golden-finger side should be fully plugged into the slot. 4. Secure the card to the board by tightening up the screw to the marked spot. 5.
- Page 10 The washer ① & the hexagonal screw nut ②. Push the washer ① through the antenna head. 7. And then lock the antenna screw head to the front side of the rear panel with the hexagonal screw nut② and tighten it up. 8.
- Page 11 9. Repeat step 6 to 8, to finish installation of the other antenna. 10. The rear panel with antenna screwheads installed. 11. Connect the external Wi-Fi receiver antenna to the antenna screw head on the rear panel.
- Page 12 V. To Install M.2 B-Key (3042/3052) card 3052 3042 1. Locate the M.2 B-Key PCIe (3042/3052) slot on the board. Prepare compatible M.2 B-Key (3042/3052) card. 2. Remove the marked screw and use it to lock compatible card to the slot in later installation. 3.
- Page 13 finger side fully emerged into the slot. 4. Install the screw back to the original spot. *Note: the screw post and nut fixed at location MH2 by default for 4.2cm M.2 B-key type-3042 card installation. If you wish to install M.2 B-key type-3052 card, please remove the M.2 B-key type- 3042 card and screw on the location MH3 before installing 5.2cm card to the slot.
- Page 14 Turn over the HDD tray and fix 2.5’’ HDD upon HDD tray by tightening 4* screws marked in corresponding spots. Plug SATA power connector and SATA port connector into connectors onboard. Adjust the installed tray as showed above. Fix HDD tray into the system by tightening up 4 screws marked.
- Page 15 VII. To Wall Mount the system 1. Install wall mount rack to the system by tightening two screws in the marked positions. 2. Then lock the other two screws on the other side in the same way. 3. Wall mount the system by tightening 4 screws in the marked positions on both sides of the wall racks.
Need help?
Do you have a question about the FDF13 Series and is the answer not in the manual?
Questions and answers