Subscribe to Our Youtube Channel
Related Manuals for JETWAY FDF20
Summary of Contents for JETWAY FDF20
- Page 1 Quick Installation Manual NO: G03-FD_MF20QIG-F Rev: 1.0 Release date: 2022-07-14 Notice: The photos in this file are for illustration purpose only. The model may not be the latest version. Please refer to the product you purchased for actual specification.
- Page 2 I/O Outlets...
- Page 3 Dimension and Outlines I. To Dissemble the Chassis 1. Locate the screws at the spots marked on this side of the system and unscrew them one by one.
- Page 4 2. Remove the marked screw on the front IO panel. 3. Remove the marked screw on the rear IO panel. 4. Lift the cover up to open the chassis. 5. The overview of the internal structure of the system with HDD tray pre-installed.
- Page 5 6. Remove the marked screws to dissemble the HDD tray from the system. 7. The overview of the internal structure of the system.
- Page 6 II. To Install SO-DIMM to the board 1. Locate the SO-DIMM slot on the board. 2. Insert the gold-finger side of the compatible SO-DIMM into the slot at a 30 degree angle. See to it that the break of the module fit into the notch of the slot and the golden-finger side should be fully plugged into the slot.
- Page 7 III. To Install M.2 M-Key SATA (2242/2280) card 2280 2242 1. Locate the M.2 SATA slot on the board. System supports two types of M.2 M-Key card in different lengths (2242/2280). Prepare compatible M.2 SATA card. 2. To install compatible card, please remove the screw in the marked spot at first. 3.
- Page 8 4. Tighten up the screw removed before to the marked spot to secure the card. *Note: The screw post and nut are fixed at location MH4 by default for 8cm type-2280 card installation. If you wish to install type-2242 card, please remove corresponding screw post under the screw as well and lock the screw post into location MH2 before installing 4.2 cm card to the slot.
- Page 9 2. Remove the marked screw and use it to lock compatible card to the slot in later installation. 3. Insert the gold-finger side of the compatible card into the slot and press down. See to it that the golden-finger side should be fully plugged into the slot. 4.
- Page 10 5. Locate the reserved antenna holes on the rear panel. Remove the dust-proof plugs on the marked spots from the panel to install the antenna. 6. Push this antenna screw head into antenna hole of the rear panel from the backside of the panel. The washer ①...
- Page 11 hexagonal screw nut② and tighten it up. 8. Press the metal hat on the end of the antenna string to corresponding antenna slot on the card as showed. 9. Repeat step 6 to 8, to finish installation of the other antenna. 10.
- Page 12 11. Connect the external Wi-Fi receiver antenna to the antenna screw head on the rear panel. V. To Install M.2 B-Key (3042) card 1. Locate the M.2 B-Key, type-3042 slot on the board. 2. Remove the marked screw with a screwdriver.
- Page 13 3. Insert the gold-finger side of compatible M.2 B-Key, type-3042 card into the slot until the golden finger side fully emerged into the slot. 4. Install the screw back to the original spot. VI. To Install Hard Disk Place compatible SATA HDD upon HDD tray as showed above. Plug this side of the cable to SATA power-in connector and SATA connector of the hard disk.
- Page 14 Turn over the HDD tray and fix 2.5’’ HDD upon HDD tray by tightening 4* screws marked in corresponding spots. Plug SATA power connector and SATA port connector into connectors onboard. Adjust the installed tray as showed above. Fix HDD tray into the system by tightening up 4 screws marked.
- Page 15 Notice: When all necessary installations are finished, please make sure that all cables unplugged before installations are connected to their original locations before restoring the back cover to the chassis and screws on the front panel/back panel/top cover locked to its original locations (Refer to Part I).
Need help?
Do you have a question about the FDF20 and is the answer not in the manual?
Questions and answers