Advertisement
Vignette Architectural Gateway
DMX-Controlled Fixtures
Ethernet
Laptop running Pathscape
software (temporary for
configuration)
OUT OF BOX OPERATION -
Step 1
Ensure all your wall stations are wired per the guide on the reverse
of this page and the last station in the bus is terminated. When the
gateway is powered, you should see BUS activity on the wired bus
terminal at the gateway and on rear of each station.
Step 2
Open Pathscape on a PC on the same network. YOU MUST USE
Pathscape software to add the device to a Security Domain and
enable Unsecured Protocols if needed (see Pathscape manual
for details on Security, and Vignette Properties > Network DMX
Receive Protocols).
Step 3
Connect your DMX512 source (console) to Port B and set up a look
that you want to snapshot. The amber Port B Input light should be
solid. If it is flashing, you do not have an active input.
NOTE: For models that do not include DMX ports, connect your source
to the same lighting network as the Vignette system. Use Pathscape
to specify the Universe that should be captured by the snapshot. See
Pathscape manual for additional details.
Step 4
Press the Record Enable button on the gateway to illuminate the red
Record Enable LED.
PWGW DIN V
DMX512
NEMA Wall Enclosure
PWENC SML HOR typical
PWPP DIN P4
Pathport
DIN-Mount
DMX/RDM
FACTORY
DEFAULT
Gateway
OUTPUT
OUTPUT
OUTPUT
OUTPUT
INPUT
INPUT
INPUT
INPUT
IDENTIFY
Port A
Port B
Port C
Port D
PROCESSOR
SD CARD OK
BUS 1
BUS 2
1
Power
Identify
Record Enable
3
5
POWER
7
BUS 3
BUS 4
PWGW DIN VE2C8
Vignette Architectural
Gateway
PWGW DIN VD2 & PWGW DIN VD2C8
DMX512
–
+
24–48VDC
7W Max
Ethernet
(Crossover)
2
WS485
4
6
8
PWWSI V485 B2 /
PWWSI LOC B4 /
PWWSI LOC B4 /
PWFP G3
Vignette Wall Station
PWWSI V485 B4 /
PWFP G1
Vignette Wall Station
Step 5
Press and hold the first button on any wall station for 5 seconds. It will
glow green when it has recorded the snapshot.
Step 6
Repeat Step 2, setting up the next look to record from your DMX
source.
Step 7
Repeat Step 5, pressing and holding subsequent buttons.
Step 8
Remove your source's DMX line from Port B. After 10 seconds your
lights will fade to black.
Step 9
Touch each of the recorded buttons. Upon pressing the buttons the
snapshots will crossfade from one to the other in 5 seconds. Start at
Step 2 if you need to record other snapshots.
Step 10
Touch the Record Enable button on the gateway to disable recording.
Installation
LED Wash Lights
DMX512
(Input)
PWINS XLR5M
[xxxx]
with
PWFP G1 [xxxx]
DMX Input Wall
Plate
Stage Management
PWWSI V485 B2 /
PWWSI LOC B4 /
PWWSI LOC B4 /
PWFP G3
Vignette Wall Station
PWWSI V485 B4 /
PWWSI V485 B4 /
PWFP G1
PWFP G1
Vignette Wall Station
Vignette Wall Station
Guide
PWCOG DT
Theatrical Lighting Console
PWWSI V485 B2 /
PWWSI LOC B4 /
PWWSI LOC B4 /
PWFP G3
Vignette Wall Station
Auditorium
08.27.21
Advertisement
