Advertisement
Quick Links
A
ASSEMBLE AUGER FEEDER KIT
Remove all hardware from packaging.
From the inside of your feeder hopper, install (3) M6 bolts,
fitted with washers, through the mounting bolt holes on
the bottom. Do not thread anything onto the bolts,
this will be the mounting hardware for the assembled
auger kit.
NOTE: Remove the rubber grommet in bottom of
hopper cone to avoid interfering with the grommet
on the Auger Kit.
On the right side of the auger kit, remove the access door by
unscrewing the (2) Phillips head screws.
The door will drop straight down after screw removal.
Remove the carabiner clip and rotate the main door downward to begin mounting the auger kit to your hopper.
With the main door open and the access door removed, lift the auger kit
up to the hopper, inserting the mounting hardware from STEP 2 through
the 3 mounting holes on top of the auger kit.
Be sure that the main door is oriented to be at the front of the feeder,
indicated by the stamping on the Hopper Cone.
Instructions for Ranch Series Auger Feeder Kit
Thank you for your purchase of a Moultrie Ranch Series Auger Feeder Kit. Please read this sheet before
operating the unit. If you should have any questions about this product or any other Moultrie product,
please contact us using the information on the back of this sheet. Allow us to better serve you by
activating your 1-year warranty online at http://www.moultriefeeders.com/warranty .
Bolt
M6 x 1 x 18
Qty. 7
Hex Nut
M6 x 1
Qty. 7
Mounting Hole
Carabiner
Clip
Main
Door
Flat Washer
M6
Qty. 8
View from inside hopper
Bolt
Washer
Grommet
Phillips
Screws
Access
Door
Advertisement
Related Manuals for Moultrie Ranch Series
Summary of Contents for Moultrie Ranch Series
- Page 1 Instructions for Ranch Series Auger Feeder Kit Thank you for your purchase of a Moultrie Ranch Series Auger Feeder Kit. Please read this sheet before operating the unit. If you should have any questions about this product or any other Moultrie product, please contact us using the information on the back of this sheet.
- Page 2 Secure the Auger kit to the mounting hardware from STEP 2 using (1) flat washer and (1) hex nut per bolt (3). (10mm wrench) Washer Hex Nut Re-install the access door by sliding it vertically back into its original location. While holding the door in place, insert the screw on the right-hand side first to help align the top screw.
- Page 3 (2) top bolts to fully secure the feed chute. Washer Bolt We recommend a Moultrie 12V 7ah Rechargeable Battery MCA-13093. THE RED CABLE CONNECTS TO THE POSITIVE (+) BATTERY TERMINAL THE BLACK CABLE CONNECTS TO THE...
- Page 4 CONFIGURING AND TESTING FEEDER INSTALL BATTERY: Open Kit by removing carabiner clip and rotate the main door downward. Install a 12V 7ah battery (Moultrie rechargeable battery MCA-13093) by attaching the Red Wire Connector to the positive (+) terminal and the Full Battery Black Wire Connector to the negative (-) terminal, making sure that the leads do not touch.
-
Page 5: Assemble The Hopper
Instructions for Ranch Series 450lb Hopper Thank you for your purchase of a Moultrie Ranch Series 450lb Hopper. Please read this sheet before operating the unit. If you should have any questions about this product or any other Moultrie product, please contact us using the information on the back of this sheet. - Page 6 Place the (4) leg brackets against the corner bracket mounting holes as shown, align the holes and insert (2) short M8 bolts from the outside of each leg bracket into the hopper. Secure with a hand-tight M8 lock nut on each bolt (8). Bracket Mounting Hole Short...
- Page 7 Insert the remaining leg sections into the (4) top-leg sections. Tap firmly on the end of the legs when joining leg sections; this will help to keep them locked together. Top Leg Sections Section (x4) INSTALL FEEDER KIT ONTO HOPPER See additional feeder kit instructions for installation.