1. Manuals
  2. Brands
  3. Haybuster Manuals
  4. Grinder
  5. H-1135
  6. Operating instructions manual

Haybuster H-1135 Operating Instructions Manual

Pto driven tub grinder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Operating Instructions and Parts Reference
H-1135
PTO Driven Tub Grinder
0500167 • D
2020
ecember
TM
P
roduct
D
T
I
I
ura
ech
nDusTrIes
nTernaTIonal
Po B
1940, J
ox
amesTown
T
: (701) 252-4601• F
el
ax
.
.
www
DuraTechInDusTrIes
neT
I
nformatIon
I
.
nc
, nD 58402-1940
: (701) 252-0502
•
.
.
www
hayBusTer
com

Advertisement

Table of Contents
loading

Related Manuals for Haybuster H-1135

Summary of Contents for Haybuster H-1135

  • Page 1 Operating Instructions and Parts Reference H-1135 PTO Driven Tub Grinder roduct nformatIon nDusTrIes nTernaTIonal Po B 1940, J , nD 58402-1940 amesTown : (701) 252-4601• F : (701) 252-0502 • 0500167 • D 2020 DuraTechInDusTrIes hayBusTer ecember...
  • Page 2 A Tradition of Innovation Since 1966...
  • Page 3 H-1135 PTO Driven Tub Grinder as of the date of publication. DuraTech Industries reserves the right to make updates to the machine from time to time. Even in the event of such updates, you should still find this manual to be appropriate for the safe operation and maintenance of your unit.
  • Page 4 A Tradition of Innovation Since 1966...
  • Page 5 • Section 2.1, “Pre-Operation Inspection”. Appropriate use of unit The H-1135 Tilt Tub Grinder is designed to grind material into more palatable or manageable rations for your operation. It has multiple uses: Grind most types of hay • Big round bales • Loose hay...
  • Page 6 WARNING: The OPERATOR IS RESPONSIBLE for the safety of the operator and those in the surrounding area. Operators and those observing the operation of the H-1135 Tub Grinder are required to wear head, eye, and ear protection, No loose clothing is allowed.

  • Page 7: Table Of Contents

    Section 2: Operation ..............19 Pre-Operating Inspection ............... 19 Introduction to the machine ..............21 2.2.1 Description of the H-1135 Tub Grinder ......... 21 2.2.2 Overview of Operator’s Controls ............ 21 2.2.3 Electronic governor ................. 22 2.2.4 Rotor ....................28 2.2.5 Screens ....................
  • Page 8 Balanced Hammer maintenance and replacement....... 59 Dodge Rotor bearing installation ............62 Cleaning the display unit ................ 65 Section 4: Troubleshooting the H-1135 ........66 Control parameters for electronic governor ......... 66 4.1A Monitor parameters for electronic governor ........67 Fault Codes ....................
  • Page 9 T A B L E O F C O N T E N T S Part 2: Parts Reference ..........73 MAINFRAME ASSEMBLY #1 ................74 MAINFRAME ASSEMBLY #2 ................76 HITCH ASSEMBLY ....................78 PLATFORM ASSEMBLY ..................80 PLATFORM ASSEMBLY DETAIL A ..............82 BULL WHEEL ASSEMBLY ................
  • Page 10 GEYSER PLATE (OPTION) ................154 MATERIAL GUIDE ASSEMBLY (OPTION) ............ 156 DECALS ......................158 DECAL LOCATIONS ..................160 H-1135 TUB GRINDER DOCUMENTATION COMMENT FORM .....163 FOLDOUTS 5701174 - H-1135 MACHINE HARNESS ............FO-1 5701170 - PTO TUB TAIL LIGHTS HARNESS ..........FO-2...

  • Page 11: Part 1: Operating Instructions

    H-1135 PTO Driven Tub Grinder Part 1: Operating Instructions H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...

  • Page 12: Introduction

    The purpose of this owner’s manual is to explain maintenance requirements and routine adjustments for the most efficient operation of your H-1135 Tub Grinder. There is also a trouble shooting section that may help in case of problems in the field. Any information not covered in this manual may be obtained from your dealer.
  • Page 13 Section 3: Describes how to maintain the H-1135 Tub Grinder. • Section 4: Describes how to trouble shoot problems with the H-1135 Tub Grinder. • Part 2: Part’s reference contains diagrams of each assembly, with the part number of each part. A key on the same or facing page contains a description of the part and the quantity used.

  • Page 14: Section 1: Safety

    Section 1: Safety The safety of the operator is of great importance to DuraTech Industries/Haybuster. We have provided decals, shield and other safety features to aid you in using your machine safely. In addition, we ask you to be a careful operator who will properly use and service your Haybuster equipment.
  • Page 15 DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations, typically for machine components that, for functional purposes, cannot be guarded. WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury, and includes hazards...

  • Page 16: Operator - Personal Equipment

    Do not operate a H-1135 when you are fatigued. Be alert - If you get tired while operating your H-1135, take a break. Fatigue may result in loss of control. Working with any farm equipment can be strenuous. If you have any condition...

  • Page 17: Machine Safety Labels

    Machine safety labels The safety decals located on your machine contain important information that will help you operate your equipment. Become familiar with the decals and their locations. DANGER: ROTATING PARTS WITHIN CAN KILL OR DISMEMBER. WAIT FOR ALL MOVEMENT TO STOP BEFORE SERVICING, UNLOADING, OR INSPECTING MACHINE.
  • Page 18 WARNING: FOR YOUR PROTECTION AND PROTECTION OF OTHERS, PRACTICE THE FOLLOWING SAFETY RULES. BEFORE OPERATING THIS MACHINE, READ THE OPERATOR’S MANUALS SUPPLIED WITH THIS MACHINE AND YOUR TRACTOR. 6500041 CHECK OPERATORS MANUALS TO BE SURE YOUR TRACTOR MEETS THE MINIMUM REQUIREMENTS FOR THIS MACHINE.
  • Page 19 WARNING: OVERHEAD CONVEYOR HAZARD TO PREVENT SERIOUS INJURY OR DEATH: 6500214 DO NOT WALK UNDER CONVEYOR AT ANY TIME. STAY CLEAR OF CONVEYOR DURING OPERATION, RAISING, AND LOWERING. LOWER CONVEYOR FULLY BEFORE SERVICING. KEEP OTHERS AWAY. WARNING: HIGH-PRESSURE FLUID HAZARD, TO PREVENT SERIOUS INJURY OR DEATH: •...
  • Page 20 WARNING: Moving parts can crush and cut. Keep hands clear. 6500488 WARNING: Noise hazzard. Ear protection required. 6500489 CAUTION: ADJUST TRACTOR DRAWBAR SO THAT DISTANCE FROM THE END OF THE PTO SHAFT ON THE TRACTOR TO THE CENTER OF THE DRAWBAR HITCH PIN IS EQUAL TO THE DISTANCE SHOWN IN DIAGRAM.

  • Page 21: Thrown Objects And Operator Safety

    Figure 1.2. Figure 1.1 VIEWED FROM THE REAR OF THE H-1135 NOTE: The difference in the size of the area for side A versus side B. Side B is larger. Dimensioning the size of this area is not practical. The distance a thrown object may travel is dependent on several conditions, including, but not limited to, rotor speed and diameter, condition of the hammers, style of hammers, object mass, object shape, amount of material in the tub, and how the hammer strikes the object.

  • Page 22: Shielding

    Shielding This H-1135 Tub Grinder is equipped with shielding at all major points of potential injury. All Shields should be kept in place during operation. Bodily injury may occur if the unit is operated without shields. WARNING: Shields are installed for your protection and to keep material off machine parts. Do not operate this Industrial Tub Grinder without shields in place.

  • Page 23: Safety Review

    Use a tractor that meets the requirements contained in this manual. See Appendix C, Required for Operation, page 71. Make sure the H-1135 Tub Grinder is in good operating condition and that all protective shields are in place and in proper working order. Replace damaged shields before operating.
  • Page 24 Because it is possible that your H-1135 may be used in dry areas or the presence of combustibles, special precautions should be taken to prevent fires and fire fighting equipment should be readily available.

  • Page 25: Fire Prevention

    Fire Prevention Grinding wood, hay, and other products in a tub grinder produces a large amount of potentially combustible material. The risks of fire can be significantly reduced with proper operating and maintenance procedures. This does include frequent removal of dust, debris, and other combustible materials. Most of the products that are ground are dry and the grinding process can produce fine, dusty material.

  • Page 26: Fire Extinguishers

    TUB GRINDER MAINTENANCE: • Repair any fuel or hydraulic leaks as quickly as they are discovered. Clean up spills immediately. Fuel or oil soaked materials can contribute significantly to the rapid spreading of a fire once it has begun. • Inspect all electrical wiring periodically.

  • Page 27: Towing

    Make sure all bystanders are clear. Hitch H-1135 Tub Grinder to a tow vehicle with adequate load carrying and braking capacity. Be sure to attach safety chains between tow vehicle and H-1135 Tub Grinder. Tongue weight is 1,900 lbs. (862 kg).

  • Page 28: Service And Maintenance

    EXPLAINED IN THE OPERATOR’S MANUAL, ADVERTISING LITERATURE OR OTHER DURATECH INDUSTRIES WRITTEN MATERIAL PERTAINING TO THE H-1135 TUB GRINDER. H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...

  • Page 29: Section 2: Operation

    There is no substitute for a sound preventative maintenance program and a well-trained operator. To insure long life and economical operation, learn how to operate the H-1135 Tub Grinder and how to use the controls properly. Thoroughly instruct the operator in maintenance and operation of the H-1135 Tub.
  • Page 30 BEFORE OPERATING CHECKS Before operating the H-1135 Tub Grinder, follow these instructions: Read and understand the operator’s manual. Learn how to operate the controls properly. Do Not let anyone operate without instruction. Know the machine’s safety features and understand the safety precautions.

  • Page 31: Introduction To The Machine

    Introduction to the machine 2.2.1 Description of the H-1135 Tub Grinder The Tub Grinder is designed to grind most types of hay, grain and crop residue such as stover and straw. The unit incorporates a number of basic features including the rotating tub, the electronic governor, the rotor and hammer assemblies, the tub chain and drive assemblies, belly auger and discharge conveyor, and the axle and hitch assemblies.

  • Page 32: Electronic Governor

    2.2.3 Electronic governor The Wachendorf A3X with an HFX32 control system will control the Tub and Discharge Conveyor functions of a Tub Grinder. Display Start up screen: Company logo Screen will show when power is applied to the display for approx. 10 sec. Loading screen: Company logo, with loading bar Screen will show right after Start up screen for approx.
  • Page 33 Home screen: Home Screen will show right after the loading screen, when the Home button is pressed from any of the other pages, or when the Encoder is pressed from the Manual Function screen. • Tub FWD/REV buttons will control the Tub FWD/REV outputs as described later in this manual. •...
  • Page 34 Manual Function Screen: The Manual Function screen will be accessed by pressing the next button or the encoder on the Home Page. The following functions can be operated on the Manual Function screen. Functions marked with and (8) can also be operated with the radio remote.
  • Page 35 Hours screen: The Hours screen will be accessed by pressing the next button on the Manual Function screen. • Pressing the Fault Menu button will take the operator to the Fault Screen page. • The Grind Hours window will display the total number of hours the machine has run with the Rotor ON. The Grind Hours can be reset using the HFX Service Tool •...
  • Page 36 Fault screen: The faults will show up in the fault table screen when they occur. The Active Fault screen will display a table indicating the J1939 DM1 message fault codes. The fault codes will be displayed as numerical values unless otherwise specified in the Fault Codes table. (See section 4.2) •...
  • Page 37 Hardkeys: Next • When the Next button is pressed, the display changes to the next screen. Home Button • When the home button is pressed the display will go to the home screen. ESC Button • When the ESC button is pressed the display will go back to the previous screen or view. Encoder •...

  • Page 38: Rotor

    2.2.4 Rotor The Rotor and screens are the heart of the tub grinder. The rotor on this H-1135 Tub Grinder is equipped with 88 swinging hammers. Dull edges on the hammers and/or screens will result in a loss of capacity and increased horse power requirements.

  • Page 39: Tub

    2.2.8 Conveyors, Lifting and Folding An electric switch on the H-1135 tub grinder controls the conveyor lift and fold. The tractor supplies hydraulic oil for operating the conveyor lift and fold system. Activate the tractors hydraulic circuit before operating the valve on the H-1135 tub grinder.

  • Page 40: Hydraulic Tilt Platform

    2.2.9 Hydraulic Tilt Platform The H-1135 tub grinder can be tilted 90 degrees for access to the rotor, screens, and drive line. Operation of the tub tilt cylinder is performed using the controls for the tractor which is located on the tractor. After using the normal shut down procedures, the hopper platform can then be opened.

  • Page 41: Machine Operation

    Machine Operation 2.3.1 Tractor Set Up A tractor drawbar and 3-point arms can cause interference with the PTO driveline. This interference can cause serious damage to the PTO guarding and the PTO telescoping members. If this implement is attached to a tractor with a clevis hitch (hammer strap) style drawbar, the hammer-strap must be removed to prevent damage to the PTO guarding and the PTO telescoping members.

  • Page 42: How To Hook Up To Tractor

    To reduce wear on the PTO shaft knuckle joints, tractor PTO shaft should be in line (parallel) with the H-1135 Tub Grinder. If tractor is equipped with swinging drawbar, adjust so the tractor PTO and H-1135 Tub grinder drive shaft are in line.

  • Page 43: How To Operate Machine As A Unit

    PTO speed for the tractor to recover automatically if a slug is encountered. GRINDING Place materials to be ground directly into the tub. The best method for filling the H-1135 Tub Grinder is: Engage Rotor and increase speed to 1000 RPM on the PTO shaft Fill the tub about half full of unground materials before starting tub rotation.
  • Page 44 EAR CORN Grinding ear corn requires a special attachment. This attachment fits directly over the rotor and uses crossbars in the tub to feed corncobs into the rotor. (See Appendix B: H-1135 Specifications under the heading “Options”.) IF LODGING OCCURS Materials may lodge against the side of the tub and not feed down to the rotor.

  • Page 45: Shutdown Procedures

    Before working on or near the H-1135 Tub Grinder for any reason, including servicing, inspecting or unclogging machine: Run H-1135 Tub Grinder until discharge conveyor is empty, and grind as much of the material in the tub as possible. Reduce engine speed to idle.

  • Page 46: Removing From Storage

    Road Transport 2.6.1 Set up to transport Inspect H-1135 Tub Grinder for any loose parts, tools, or any materials. Remove them or fasten them securely to the H-1135 Tub Grinder. To set up the H-1135 for transport, perform the following steps: Fold the conveyor.

  • Page 47: Raising The Tub Platform

    Raising the Tub Platform WARNING: To prevent serious injury or death, do not tilt platform on unlevel ground or with material in the tub. To raise the tub platform, perform the following steps: Park machine on firm level ground or surface. Remove all material from tub.

  • Page 48: Operation Of The Electronic Governor

    Operation of the Electronic Governor Auto/Manual Mode The system has two modes of operation: Auto Mode and Manual Mode. The mode of operation can be toggled using the Auto/Manual button on the display. Tub Forward • If the Tub Forward button is pressed on the display or the radio remote, and the Tub Forward output is de-active, and the Tub Reverse output is de-active, and either the Rotor Speed input is greater than zero, or the system is in Manual Mode: •...
  • Page 49 Warning If the Tub Forward button is pressed on the display, and the Tub Forward output is de-active, and the Tub Reverse output is de-active, and the Rotor Speed input is less than zero, and the system is in Auto Mode: •...
  • Page 50 If the Tub Reverse output is active, and the system is switched from Manual Mode to Auto Mode while the Rotor Speed input is zero, or the Tub Forward button is pressed on the display or the radio remote, or the Tub Reverse button is pressed on the display: •...
  • Page 51 Tub Speed • The Tub Speed ramp rate and output current will have adjustable parameters in the Impulse Service Tool. Manual Mode: • The Tub will operate in an open loop control mode and will not compensate for rotor rpm changes.
  • Page 52 • If the Set Speed button is pressed when the Rotor Speed is greater than the Set Speed Limit High RPM: • The following alarm window will be shown on the display for 3 seconds. • Rotor Speed Min Limit is the RPM where the Tub will stop when the Engine Load is set to 100%.
  • Page 53 Conveyor • If the Conveyor button is pressed on the display and the Conveyor Forward output is de-active and the Rotor Speed input is greater than zero or the system is in Manual Mode: • Conveyor Forward output will be activated. •...

  • Page 54: Adjusting The Conveyor Belt Tension

    Adjusting the conveyor belt tension The rollers on the discharge conveyor are adjustable to allow for belt stretching and tracking. If the conveyor belt slows down or stops during operation, slippage may be the cause. To eliminate slippage, tighten the adjusting bolts on the conveyor equally.

  • Page 55: Adjusting The Conveyor Belt Tracking

    2.10 Adjusting the conveyor belt tracking When a new belt is installed: Use only genuine DuraTech Industries parts. Begin by adjusting the drive roller so that the mounting bearings are the same distance from the end of the conveyor frame. This ensures that the roller centerline is square with conveyor frame. Adjust the idler roller tension bolts so that they are equal on both sides of the conveyor.

  • Page 56: Adjusting Tub Chain Tension

    2.11 Adjusting tub chain tension To adjust the tub chain tension, perform the following steps: lock bolts Loosen (4) bolts holding motor mounting plate. Turn (2) adjusting bolts to set chain tension. Tighten the (4)bolts holding motor mounting plate. chain path adjusting bolts H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...

  • Page 57: Main Drive Belt Adjustment

    A spring tensioning system is used on the H-1135 grinder to maintain tension as belts stretch over time. To properly tension the drive belts turn the tensioning rod until the spring caps come into contact with the tubes that the springs are seated into. DO NOT OVERTIGHTEN! The two sheaves must be running parallel, if they are not the belts will not track, premature belt wear or belts running off of the sheaves will result.

  • Page 58: Sensor Test

    Figure 2.7 sheave alignment 2.13 Sensor test Set the gap between the sensor and the sprocket to 3/32” (2.4 mm). Sensor resistance should be 900 ohms +/- 10%. H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...

  • Page 59: Belly Auger Drain Covers

    2.14 Belly auger drain covers Belly auger drain covers should be in the open position to allow any moisture to drain out. When grinding small grains the belly auger covers should be in the closed position to keep the grain from spilling out. H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...

  • Page 60: Section 3: General Maintenance

    Before working on or near the H-1135 Tub Grinder for any reason, including servicing, inspecting or unclogging machine: Run H-1135 Tub Grinder until discharge conveyor is empty, and grind as much of the material in the tub as possible. Reduce engine speed to idle.

  • Page 61: Lubrication

    If the lubricant is caked and the bearing seems dry, wash the bearing to remove old grease. Repack the bearing. Lubrication CAUTION: Follow normal shutdown procedure before adjusting or lubricating. When operating the H-1135 Tub Grinder during cold weather, perform all lubrication after bearings are at operating temperatures. BEARING LUBRICATION Bearings operating in the presence of dust and water should contain as much grease as speed will permit, since a full bearing with a slight leakage is the best protection against entrance of foreign material.
  • Page 62 Lubrication Chart H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...
  • Page 63 Figure 3.1 rotor bearing lubrication point rotor bearing lubrication point 1 of 2 (Ref # 3) Figure 3.2 belly auger bearing front rotor bearing lubrication point 2 of 2 (Ref # 3) lubrication points and rotor bearing lubrication point belly auger lubrication points (Ref # 5) Figure 3.3 tub chain idler pivot lubrication point...
  • Page 64 Figure 3.4 jack shaft lubrication points (Ref #1) jack shaft bearing and bull wheel bearing lubrication points bull wheel bearing lubrication points (Ref #6) Figure 3.5 tub pivot lubrication points tub pivot lubrication points (Ref #4) Figure 3.6 tub roller, tub pressure roller and roller chain pressure roller roller chain...
  • Page 65 Figure 3.7 PTO lubrication points PTO lubrication points (Ref #9) Figure 3.8 discharge conveyor bearings (2 of 4) discharge conveyor bearing lube points (Ref #7) Figure 3.9 discharge conveyor bearings lubrication points (2 of 4) discharge conveyor bearing lube points -one on each side of machine (Ref #7) Figure 3.10 conveyor lift pivot...

  • Page 66: Hydraulic System

    Hydraulic system CAUTION: Lack of proper oil level in the reservoir tank will cause system to heat under continuous running. Check the hydraulic oil level daily and replace as necessary. Hydraulic Oil Reservoir Capacity: 60 gallons All machines have been pre-run at the factory to insure all hydraulic oil fill functions are preforming correctly.

  • Page 67: Screens

    CAUTION: Follow normal shutdown procedure before entering tub to do any service work. To change screens on the H-1135, perform the following steps: Raise the tub platform using the following steps WARNING: To prevent serious injury or death, do not tilt platform on unlevel ground or with material in the tub.

  • Page 68: Hammermill Maintenance

    Hammermill maintenance Visually examine the mill to see if any of the internal parts show excessive wear. These parts should include rotor discs and the holes in the discs that support the rods. Enlarged holes can cause rods to break or bend. Also check rods, rod locking or retaining devices, hammers, screens, screen tracks and hold downs, main shaft, platform locking devices, hinges or anything else that could wear and perhaps fail and causing damage to the hammermill and/or personnel safety if not properly maintained.

  • Page 69: Balanced Hammer Maintenance And Replacement

    (See figure 3.11 Hammer Layout) Having received four boxes of forged hammers for a complete set of (88) H-1135 hammers, each box has two rows of (11) hammers for a total of 22 hammers. Each box is designated with the number of which rods each row of 11 hammers needs to be installed on.
  • Page 70 To replace the hammers on this machine, perform the following steps: Raise the tub platform following the instructions in Section 2.7 “Raising the tub platform”. WARNING: To prevent serious injury of death, do not tilt platform on unlevel ground of with material in the tub.
  • Page 71 Figure 3.12 hammer spacing chart for the H-1135 H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...

  • Page 72: Dodge Rotor Bearing Installation

    3.6 Dodge Rotor bearing installation WARNING: To ensure the rotor is not unexpectedly started, turn off and lock out or tag the power sources before proceeding. Failure to observe these precautions could result in bodily injury. NOTE: Bearing housing caps and bases are not interchangeable and must be matched with mating half.
  • Page 73 MOUNTING Install the non expansion unit first. Apply a coating of light oil or other rust inhibitor to the adapter area of the shaft. Before mounting bearing to shaft, remove lockplate from bearing and turn locknut counterclockwise one to two turns to allow adapter Picture 1 to expand fully.
  • Page 74 Once “ZERO reference point” is reached, scribe a line through both locknut face and adapter face (Picture 2). Then continue to tighten the locknut (Picture 3) by turning it clockwise using hammer and drift or spanner by the appropriate rotation angle shown on Table 1.

  • Page 75: Cleaning The Display Unit

    3.7 Cleaning the display unit NOTE: Do NOT use high pressure when cleaning the display screen unit. Using high pressure washers will cause damage to the display screen and is not covered by warranty. H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...

  • Page 76: Section 4: Troubleshooting The H-1135

    Section 4: Troubleshooting the H-1135 4.1 Control parameters for electronic governor H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...

  • Page 77: A Monitor Parameters For Electronic Governor

    4.1A Monitor parameters for electronic governor Fault Codes H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...

  • Page 78: General Troubleshooting

    General Troubleshooting H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...

  • Page 79: Appendix A: Warranty

    Appendix A: Warranty DuraTech Industries International Inc. warrants to the original purchaser for 12 months from purchase date that this product will be free from defects in material and workmanship when used as intended and under normal maintenance and operating conditions. This warranty is limited to the replacement of any defective part or parts returned to our factory in Jamestown, North Dakota, USA, within thirty (30) days of failure.

  • Page 80: Appendix B: H-1135 Specifications

    Feed Delivery ....26 ft. folding rubber belt conveyor w/cleats 24 in. Wide Tub size ..................8’-11” (2.72 m) ID Tub Depth ..................50 in. (1.27 m) Tub Drive ..................Electro-Hydraulic Options AVAILABLE OPTIONS FOR DURATECH INDUSTRIES H-1135 TUB GRINDER: • Ear Corn Kit • Geyser Plate •...

  • Page 81: Appendix C: Required For Operation

    Appendix C: Required for operation Tractor - 200 to 315 hp 1000 RPM PT0 Shaft Dual Hydraulics, double acting control valve, 8 GPM, 1500 psi (30.31 lpm x 10,345 Kpa) See also Section 2.3.1, Tractor Set Up. H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...
  • Page 82 A Tradition of Innovation Since 1966 H - 1 1 3 5 T U B G R I N D E R O P E R A T I N G I N S T R U C T I O N S...

  • Page 83: Part 2: Parts Reference

    H-1135 PTO Driven Tub Grinder Part 2: Parts Reference...
  • Page 84 M A I N F R A M E A S S E M B L Y # 1 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 85 M A I N F R A M E A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 2600861 WHL\ASSY\16.5SLX16.1X14PLY8BOLT-WHL\16.1X14\3/8POS (SEE WHEEL AND HUB) 2900140 HUB\ASSY\H817\8BOLT\8”B.C.\6”PILOT (SEE WHEEL AND HUB) 4100030 PIN 1” X 3-1/2” HYD. CYL. 4100144 CYL\HYD\4X30\1-3/4 ROD\CLEVIS ENDS\O-RING PORTS 4100261...

  • Page 86: Mainframe Assembly #2

    M A I N F R A M E A S S E M B L Y # 2 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 87: Mainframe Assembly #1

    M A I N F R A M E A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 2600861 WHL\ASSY\16.5SLX16.1X14PLY8BOLT-WHL\16.1X14\3/8POS (SEE WHEEL AND HUB) 2900140 HUB\ASSY\H817\8BOLT\8”B.C.\6”PILOT (SEE WHEEL AND HUB) 4100030 PIN 1” X 3-1/2” HYD. CYL. 4100144 CYL\HYD\4X30\1-3/4 ROD\CLEVIS ENDS\O-RING PORTS 4100261...

  • Page 88: Hitch Assembly

    H I T C H A S S E M B L Y H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 89 H I T C H A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 1100285 CHAIN\3/8\SFTY\AG\21000LB 4500754 BELT\BRKT\PTO 4502674 BRKT\STAND\PTO\1030 4502773 HITCH\PTO\H1030 4704337 BUSHING\MNT\CHAIN\SAFETY 4704338 WASHER\CHAIN\SAFETY 4800033 BOLT\HEX\3/4X2 4800041 BOLT\HEX\1/2X5 4800082 BOLT\HEX\1/2X1-1/2 4800248 BOLT\HEX\3/4X6 4800283 BOLT\HEX\3/4X2-1/4 4800492 BOLT\HEX\3/4X5-1/2\GR8\NC 4800908...

  • Page 90: Platform Assembly

    P L A T F O R M A S S E M B L Y H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 91 P L A T F O R M A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 4501131 SHIM\RLLR\SPPRT\TUB 4704069 RLLR\TUB\ASSY\STEEL\CAST 4501476 SHIM\RLLR\PRESS 4501518 SHLD\DRIVE\TUB 4501915 BRKT\SHLD\CHAIN\DRIVE\TUB 4501916 BRKT\SHLD\CHAIN\DRIVE\TUB 4501931 PIN\PLFRM\TILTCYL 4501932 WASH\1-3/4 O.D. 4502088 CVR\DRV\TUB 4502089 DOOR\DRV\TUB 4502401...

  • Page 92: Platform Assembly Detail A

    P L A T F O R M A S S E M B L Y D E T A I L A H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 93 P L A T F O R M A S S E M B L Y D E T A I L A ITEM PART QTY. PART DESCRIPTION 4501131 SHIM\RLLR\SPPRT\TUB 4704069 RLLR\TUB\ASSY\STEEL\CAST 4501476 SHIM\RLLR\PRESS 4501518 SHLD\DRIVE\TUB 4501915 BRKT\SHLD\CHAIN\DRIVE\TUB 4501916 BRKT\SHLD\CHAIN\DRIVE\TUB 4501931 PIN\PLFRM\TILTCYL 4501932...

  • Page 94: Bull Wheel Assembly

    B U L L W H E E L A S S E M B L Y H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 95 B U L L W H E E L A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 1400605 SHVE\5V-8\21.2\85V2120J 1400642 BUSH\QD\J\2-3/4 1600102 V-BELT\5VP850 2000509 BRG\PB\2-3/4\E\DODGE 2000510 BRG\PB\2\2BOLT 4501170 BOLT\FRM\TGHTNR\CHAIN\TUB 4502330 WHL\BULL\FRM\OFFSET 4502331 SHFT\WHL\BULL\OFFSET 4502333 SHIM\BRG\WHL\BULL 4502334 SHM\THN\BRG\WHL\BLL 4502338...

  • Page 96: Rotor Assembly

    R O T O R A S S E M B L Y H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 97 R O T O R A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 2000585 BRG\PB\3-1/4\ISAF\NON-EXP 2000586 BRG\PB\3-1/4\ISAF\EXP 2900162 CAP\END\BRG\3-1/4\ISAF 4500142 NUT\CYL\3-1/2 4500626 WASH\THRUST\3-5/8IDX6 4502318 PL\RTR\1/2X3-1/2ID\1-1/4RDS\TPPD 4502321 PL\RTR\3.5X1/2X15.75\1-1/4RDS\FCD 4502643 HOLDDOWN\SCRN\LASERED 4502670 SHIM\BRG\RTR 4502694 SPCR\CAST\8.645ODX3.503IDX1.773 THICK 4502695 SPCR\CAST\8.645ODX3.503IDX1.773 THICK 4502986 SHFT\RTR\3-1/2X71-3/4\3-1/4BRG...

  • Page 98: Pump Drive Line

    P U M P D R I V E L I N E H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 99 P U M P D R I V E L I N E ITEM PART QTY. PART DESCRIPTION 1000295 SPKT\60\TPR\20\2012\REV 1100064 CHAIN\60DBL\CL 1100193 CHAIN\60DBL\19 1400624 BUSH\R2\3 1400658 BUSH\TAPER\1-1/2\2012\W/KEY 1400667 SHVE\5V-8\9.75\F 2001052 BRG\PB\3\IMPRL\NON-EXP 2001053 BRG\PB\3\IMPRL\EXP 3600156 FLG\DRLIN\3\1710 3600907 DRLIN\COMP\19.25\1710 4200142 PUMP\HYD\TNDM\1.78CIDX1.3CID 4502617 SEAL\ADJ\SHFT\RTR 4502665...

  • Page 100: 3600907 Driveline

    3 6 0 0 9 0 7 D R I V E L I N E H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 101 3 6 0 0 9 0 7 D R I V E L I N E ITEM PART QTY. PART DESCRIPTION 3600152 FLANGE YOKE 1710 3600153 SLIP YOKE 1710 3600154 YOKE SHAFT 1710 3600155 JOURNAL AND BEARING KIT 1710 3600907 DRLIN\COMP\19.25\1710 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 102: Tub Drive Assembly

    T U B D R I V E A S S E M B L Y H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 103 T U B D R I V E A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 1000237 SPKT\80\B\40\2-1/4\1/2KW 1100070 CHAIN\2080\CL 1100071 CHAIN\2080\OL 1100260 CHAIN\2080\183 4200121 MTR\HYD\40.6\1000\2-1/4\1-5/16FOR 4501328 BOLT\HEX\3X4X8-1/2 4501331 RLLR\DR\TUB 4501383 BRKT\SPRING\ 4501705 BRKT\RLLR\TNSN 4501707 BRKT\MTR\DRV\TUB 4502642 FRM\PLFRM\TILT\1130\RTR\REAR...

  • Page 104: Tub Assembly

    T U B A S S E M B L Y H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 105 T U B A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 4502346 TUB\H1100\TTH\CNTNS 4502409 AGTTR\TUB\FIN\10 4502410 AGTTR\TUB\FIN\14 4800106 BOLT\HEX\5/8X1-1/2 4900005 NUT\HEX\5/8\NC 5000003 WASH\LOCK\5/8 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 106: Belly Auger Assembly

    B E L L Y A U G E R A S S E M B L Y H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 107 B E L L Y A U G E R A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 1400659 CPLR\RIGID\1.5X1.25 2000587 BRG\FLG\2”-BLT\SSCRW 2000588 BRG\FLG\2-1/2\4-BLT\D-LOCK 3900005 MTR\HYD\14.9\2000\SAE;A 4502312 ADJSTR\BRG\FR 4502427 SH\SIDE\PAN\CNVYR 4502603 CVR\HOLE\DRN 4502657 WELD\PAN\CNVYR\BELLY\H1130 4502658 AUGER\RIGHT 4502659 AUGER\LEFT...

  • Page 108: Lower Discharge Conveyor Assembly

    L O W E R D I S C H A R G E C O N V E Y O R A S S E M B L Y H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 109 L O W E R D I S C H A R G E C O N V E Y O R A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 1700231 BELT\CNVYR\24X606\CLEATED 2000303 BRG\FLG\1-1/2\BOLT 4100030 PIN 1”...

  • Page 110: Upper Discharge Conveyor Assembly

    U P P E R D I S C H A R G E C O N V E Y O R A S S E M B L Y H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 111 U P P E R D I S C H A R G E C O N V E Y O R A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 1400659 CPLR\RIGID\1.5X1.25 2000320 BRG\TUU\1-1/2\W-ECC\BSEAL 3900014 MTR\HYD\9.6\2000\1-1/4SH 4502227 BRKT\ARM\TORQUE\MTR...

  • Page 112: Hydraulic Oil Tank Assembly

    H Y D R A U L I C O I L T A N K A S S E M B L Y H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 113 H Y D R A U L I C O I L T A N K A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 3800301 FTG\1-5/16MOR\PLUG\HEX 3800718 FTG\3/4FOR\WELD\FLG 3801006 FTG\2-1/2FOR\WELD\FLG\HVY 4400043 FILTER\HYDRAULIC\RETURN\IN-TANK ELEMENT 4400074 4400066 GAUGE\FLTR\25PSI\1/8NPTF\COLOR CODED 4400067 FLTR\SCRN\2-1/2MORX1-7/8FOR\30GPM\ST30-100RV3...

  • Page 114: Tandum Hydraulic Pump

    T A N D U M H Y D R A U L I C P U M P ITEM PART NO. QTY. PART DESCRIPTION 4200142 PUMP\HYD\TNDM\1.78CIDX1.3CID 4200161 PUMP\SEAL\KIT\4200142 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 115: 4000598 Hydraulic Valve - View 1

    4 0 0 0 5 9 8 H Y D R A U L I C V A L V E - V I E W 1 ITEM PART NO. QTY. PART DESCRIPTION 4000230 VALVE\HYD\PILOT\PISTON 4000231 VALVE\HYD\CART\CHECK\CV0820\100P 4000347 VALVE\HYD\SOL\12V\E10\DTZ\W/DIODE 4000446 VALVE\CHECK\CART\CV1020 4000510 VLV\HYD\RELIEF\CART\3000...

  • Page 116: 4000598 Hydraulic Valve - View 2

    4 0 0 0 5 9 8 H Y D R A U L I C V A L V E - V I E W 2 ITEM PART NO. QTY. PART DESCRIPTION 4000230 VALVE\HYD\PILOT\PISTON 4000231 VALVE\HYD\CART\CHECK\CV0820\100P 4000347 VALVE\HYD\SOL\12V\E10\DTZ\W/DIODE 4000446 VALVE\CHECK\CART\CV1020 4000510 VLV\HYD\RELIEF\CART\3000...

  • Page 117: Machine Hydraulics Schematic

    M A C H I N E H Y D R A U L I C S S C H E M A T I C H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 118: Oil Tank Hydraulics

    O I L T A N K H Y D R A U L I C S H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 119 O I L T A N K H Y D R A U L I C S ITEM PART QTY. PART DESCRIPTION 3800301 FTG\1-5/16MOR\PLUG\HEX 3800486 FTG\1-5/8FJICX1-5/8MJICX1-5/8MJIC\RUN;TEE 3800530 FTG\3/4MORX9/16MJIC\ST 3800740 VALVE\BALL\1-1/2\1-7/8FOR\1/4 TURN\W/LOCK 3800745 FTG\1-7/8MORX1-7/8MOR\ADPT 3800808 FTG\1-7/8MORX1-5/8MJIC\ST 3801030 FTG\1-5/8FJIC\CAP 4000601 VLV\CHECK\POPPET\9/16MJIC 4400043 FILTER\HYDRAULIC\RETURN\IN-TANK ELEMENT 4400074 4502799 TANK\OIL\60GAL...

  • Page 120: Tandum Pump Hydraulics

    T A N D U M P U M P H Y D R A U L I C S H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 121 T A N D U M P U M P H Y D R A U L I C S ITEM PART QTY. PART DESCRIPTION 3800277 FTG\1-1/16MORX1-1/16MJIC\ST 3800470 FTG\1-5/8MORX1-5/8MJIC\ST 3800532 FTG\1-1/16MORX1-1/16MJIC\45 3800741 FTG\1-5/8MORX1-5/8MJIC\90 4200142 PUMP\HYD\TNDM\1.78CIDX1.3CID 3701595 HOSE\HYD\1-1/4X49\1-5/8FJICX1-5/8FJIC SUPPLY PORT FRONT PUMP TO RIGHT TANK PORT SCREEN 3701595 HOSE\HYD\1-1/4X49\1-5/8FJICX1-5/8FJIC...

  • Page 122: Aux Valve Hyd - View A

    A U X V A L V E H Y D - V I E W A H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 123 A U X V A L V E H Y D - V I E W A ITEM PART QTY. PART DESCRIPTION 3800694 FTG\3/4FOR\QUICK;CPLR\MALE 3800696 FTG\7/8MORX3/4MJIC\90 3800757 FTG\9/16MORX9/16MJIC\90 4000598 VLV\HYD\AUX\BLK\MFLD\12V 3700985 HOSE\HYD\1/2X144\3/4MORX3/8FJICS TRACTOR TO IN PORT AUX. VALVE 3700985 HOSE\HYD\1/2X144\3/4MORX3/8FJICS TRACTOR TO OUT PORT AUX.

  • Page 124: Aux Valve Hyd - View B

    A U X V A L V E H Y D - V I E W B H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 125 A U X V A L V E H Y D - V I E W B ITEM PART QTY. PART DESCRIPTION 3800532 FTG\1-1/16MORX1-1/16MJIC\45 3800535 FTG\7/8MORX1-1/16MJIC\90 3800728 FTG\1-5/16MORX1-5/16MJIC\90 3800757 FTG\9/16MORX9/16MJIC\90 4000598 VLV\HYD\AUX\BLK\MFLD\12V 4700777 CLMP\HOSE\1/2 7501337 CLMP\HOSE\CUSH\3/4 3701567 HOSE\HYD\1-1/4X74\1-5/16FJCX1-5/8FJC90DEG T PORT AUX VALVE TO TANK FILTER 3701423 HOSE\HYD\3/4X36\1-1/16FJC90X1-1/16FJC MC PORT AUX VALVE TO MOTOR PORT B BELLY AUGER...

  • Page 126: Aux Valve Hyd - View C

    A U X V A L V E H Y D - V I E W C H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 127 A U X V A L V E H Y D - V I E W C ITEM PART QTY. PART DESCRIPTION 3800757 FTG\9/16MORX9/16MJIC\90 4000598 VLV\HYD\AUX\BLK\MFLD\12V 7501387 CLMP\HOSE\CUSH\3/8\TWIN 3701761 HOSE\HYD\3/8X124\9/16FJICS PORT 3A AUX VALVE TO 4TH FROM REAR ON CONVEYOR BLOCK BOTTOM 3701761 HOSE\HYD\3/8X124\9/16FJICS PORT 3B AUX VALVE TO 3RD FROM REAR ON...

  • Page 128: Tub Rotation Hydraulics

    T U B R O T A T I O N H Y D R A U L I C S H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 129 T U B R O T A T I O N H Y D R A U L I C S ITEM PART QTY. PART DESCRIPTION 3800328 FTG\7/8MORX3/4MJIC\ADPT 3800938 FTG\1-5/16MORX3/4MJIC\ADPT 4000598 VLV\HYD\AUX\BLK\MFLD\12V 4200121 MTR\HYD\40.6\1000\2-1/4\1-5/16FOR 3701566 HOSE\HYD\1/2X175\3/4FJICSX3/4FJIC45 PORT MA AUX. VALVE TO UPPER PORT ORBIT MOTOR 3701566 HOSE\HYD\1/2X175\3/4FJICSX3/4FJIC45 PORT MB AUX.

  • Page 130: Tub Tilt Hydraulics

    T U B T I L T H Y D R A U L I C S H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 131 T U B T I L T H Y D R A U L I C S ITEM PART QTY. PART DESCRIPTION 3800453 FTG\3/4MORX9/16MJIC\90 3800757 FTG\9/16MORX9/16MJIC\90 3800844 FTG\3/4MOR\ORIFICE\0.062” 4000598 VLV\HYD\AUX\BLK\MFLD\12V 4100144 CYL\HYD\4X30\1-3/4 ROD\CLEVIS ENDS\O-RING PORTS 3701479 HOSE\HYD\3/8X50\9/16FJIC 2A PORT AUX VALVE TO ROD END TUB TILT CYL. 3701407 HOSE\HYD\3/8X26\9/16FJICS 2B PORT AUX VALVE TO BASE END TUB TILT CYL.
  • Page 132 B E L L Y A U G E R H Y D R A U L I C S & G R E A S E L I N E S # 1 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 133: Belly Auger Hydraulics & Grease Lines #2

    B E L L Y A U G E R H Y D R A U L I C S & G R E A S E L I N E S # 2 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 134 A Tradition of Innovation Since 1966 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 135: Belly Auger Hydraulics & Grease Lines #1

    B E L L Y A U G E R H Y D R A U L I C S & G R E A S E L I N E S ITEM PART QTY. PART DESCRIPTION 3701485 HOSE\LUB\1/8X22.5\MPS-MPS 3701486 HOSE\LUB\1/8X35.25\MPS-MPS 3701487 HOSE\LUB\1/8X27.25\MPS-MPS...

  • Page 136: Conveyor Lift And Fold Cylinder Hydraulics

    C O N V E Y O R L I F T A N D F O L D C Y L I N D E R H Y D R A U L I C S H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 137 C O N V E Y O R L I F T A N D F O L D C Y L I N D E R H Y D R A U L I C S ITEM PART QTY. PART DESCRIPTION 3800428 MNFLD\DBL;TEE\BLK\3/4FOR...

  • Page 138: Conveyor Flow Control Valve Hydraulics

    C O N V E Y O R F L O W C O N T R O L V A L V E H Y D R A U L I C S H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 139 C O N V E Y O R F L O W C O N T R O L V A L V E H Y D R A U L I C S ITEM PART QTY. PART DESCRIPTION 3800277 FTG\1-1/16MORX1-1/16MJIC\ST 3800463 FTG\1-1/16MORX1-1/16MJICX1-1/16MJIC\RUN;TEE...

  • Page 140: Discharge Conveyor Orbit Motor Hydraulics

    D I S C H A R G E C O N V E Y O R O R B I T M O T O R H Y D R A U L I C S H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 141 D I S C H A R G E C O N V E Y O R O R B I T M O T O R H Y D R A U L I C S ITEM PART QTY. PART DESCRIPTION 3800527 FTG\7/8MORX1-1/16MJIC\ST...

  • Page 142: Pressure Gauges

    P R E S S U R E G A U G E S H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 143 P R E S S U R E G A U G E S ITEM PART QTY. PART DESCRIPTION 3800381 GAUGE\3000PSI\REAR STEM 3800758 FTG\9/16MJICX1/4FP\ADPT 3800763 FTG\7/16MORX9/16MJIC\ST 4000598 VLV\HYD\AUX\BLK\MFLD\12V 3701766 HOSE\HYD\3/8X65\9/16FJC90X9/16FJC CNVYR PRESSURE GAUGE TO G1 AUX VALVE 3701766 HOSE\HYD\3/8X65\9/16FJC90X9/16FJC TUB PRESSURE GAUGE TO G2 AUX VALVE H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 144: Wheels And Hubs

    W H E E L S A N D H U B S H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 145 W H E E L S A N D H U B S ITEM PART QTY. PART DESCRIPTION 2600053 TIRE\16.5LX16.1SL\14PLY 2600649 WHL\8-BOLT\16.1X14C\8K 2900125 HUB\H817\CONE\OUTER 2900126 HUB\H817\CUP\OUTER 2900127 CUP\INNER\WHL:HUB(48510 2900128 HUB\H817\CONE\INNER 2900140 HUB\8-BOLT\W/RACES\W/NUTS 2900130 CAP\DUST\H817 2900131 SEAL\GREASE\H817 4900053 NUT\CASTLE\1-1/4\NF 4900114 NUT\TAPER\WHEEL\5/8\NF 5000065 WASH\2.5OD\1.25ID\224 8101600...

  • Page 146: Orbit Motor

    O R B I T M O T O R H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 147 O R B I T M O T O R ITEM PART QTY. PART DESCRIPTION 3900014 MTR\HYD\9.6\2000\1-1/4SH 6200004 KEY\SQ\5/16X1-1/2 3900011 MTG FLG(2000 SER) 7501005 KIT\SEAL\2000ORBIT H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 148: 3600831 Pto Assembly

    3 6 0 0 8 3 1 P T O A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 3600831 PTO\COMP\77E\20SP\1-3/4 3600738 CROSS&BRG\77E\WSLR 3600741 YOKE\77E\1-3/4\LOCK\AUTO 3600775 LOCK\SAFTY;SLD\KIT\1-3/4\77E 3600852 JOINT&TUBE\77E\3600831 3600853 YOKE&SHAFT\77E\3600831 3600854 GUARD\PTO\1-3/4\77E\20SPLN\OUTER 3600855 GUARD\PTO\1-3/4\77E\20SPLN\INNER 3600856 YOKE&TUBE&SLEEVE\77E\3600831 3600871 PTO\HALF\TRACTOR\3600831...

  • Page 149: 3600832 Pto Assembly

    3 6 0 0 8 3 2 P T O A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 3600832 PTO\COMP\77E\21SP\1-3/8 3600738 CROSS&BRG\77E\WSLR 3600777 LOCK\SAFTY;SLD\KIT\1-3/8\77E 3600872 PTO\HALF\TRACTOR\3600832 3600873 PTO\HALF\MACHINE\3600831 & 3600832 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 150: Pressure Roller Assembly

    P R E S S U R E R O L L E R A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 4500247 PRESSURE ROLLER COMPLETE 10” SPINDLE 4501090 SINGLE STAND 10” SPINDLE 2900055 SEAL 2900018 INNER CONE 2900004...

  • Page 151: Tub Roller Bearing Assembly

    T U B R O L L E R B E A R I N G A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 1200013 RLLR\TUB\1-1/2\W/O FLANGE 2000584 BRG\CYL\1-1/2\DLOK 4702007 BRG\PB\RLLR\TUB\ASY\W/BRGINSRT 4704069 RLLR\TUB\ASSY\STEEL\CAST (INCLUDES #1, #2 & #3) NOT SHOWN 4800930 BOLT\FLG\SERR\1/2X2\NC...

  • Page 152: Hydraulic Cylinder Seals And Other Items

    H Y D R A U L I C C Y L I N D E R S E A L S A N D O T H E R I T E M S H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 153 H Y D R A U L I C C Y L I N D E R S E A L S A N D O T H E R I T E M S ITEM PART QTY. PART DESCRIPTION 4100144 CYL\HYD\4X30\1-3/4 ROD\CLEVIS ENDS\O-RING PORTS 4100180...

  • Page 154: Electrical Parts

    E L E C T R I C A L P A R T S H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 155 E L E C T R I C A L P A R T S ITEM PART QTY. PART DESCRIPTION 4800277 BOLT\HEX\1/4X1 4900009 NUT\HEX\1/4\NC 5000024 WASH\LOCK\1/4 5700329 SWITCH\RCKR\PLUG 5700333 SWITCH\RCKR\MNT\PNL\MTPL 5700547 SWITCH\RCKR\DPST\12V\2LIT\15A\LATCH\W/RASED BRCKT 5701189 CNTRL\HFX32 5701234 DSPLY\WACH\OPUS\A3X NOT SHOWN 4300089 SNSR\PROX\M12X60 4502789 SHIM\CNTRLLR...

  • Page 156: Grain Hopper #1 (Option)

    G R A I N H O P P E R # 1 ( O P T I O N ) H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 157 G R A I N H O P P E R # 1 ( O P T I O N ) ITEM PART QTY. PART DESCRIPTION 4501347 HPPR\GRAIN\ASSY\COMPLETE 4501335 HPPR\GRAIN 4501340 CVR\RTR\HPPR\GRAIN 4501341 CVR\END\HPPR\GRAIN 4800003 BOLT\HEX\3/8X1 4800034 BOLT\HEX\3/8X1-1/2 4900002 NUT\HEX\3/8\NC 5000001 WASH\FLAT\3/8 5000019...

  • Page 158: Grain Hopper #2 (Option)

    G R A I N H O P P E R # 2 ( O P T I O N ) H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 159 G R A I N H O P P E R # 2 ( O P T I O N ) ITEM PART QTY. PART DESCRIPTION 4501347 HPPR\GRAIN\ASSY\COMPLETE 4501335 HPPR\GRAIN 4501340 CVR\RTR\HPPR\GRAIN 4501341 CVR\END\HPPR\GRAIN 4800003 BOLT\HEX\3/8X1 4800034 BOLT\HEX\3/8X1-1/2 4900002 NUT\HEX\3/8\NC 5000001 WASH\FLAT\3/8 5000019...

  • Page 160: Mill Grate - 9 Bar - 2-1/2

    M I L L G R A T E - 9 B A R - 2 - 1 / 2 ” H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 161 M I L L G R A T E - 9 B A R - 2 - 1 / 2 ” ITEM PART QTY. PART DESCRIPTION 4502678 BAR\GRATE\MILL\9BAR 4502832 PL\SIDE\GRATE\MILL 4502834 PL\SIDE\GRATE\MILL\9 BAR 4800010 BOLT\HEX\5/8X2 4800070 BOLT\HEX\1/2X2-1/2 4800351 BOLT\HEX\1/2X2-3/4 4900001 NUT\HEX\1/2\NC 4900005 NUT\HEX\5/8\NC...

  • Page 162: Ear Corn Kit (Option)

    E A R C O R N K I T ( O P T I O N ) H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 163 E A R C O R N K I T ( O P T I O N ) ITEM PART QTY. PART DESCRIPTION 4500128 PIPE\CROSS\2X107 4500751 BRKT\COVER\ROTOR\EARCORN 4501052 CVR\RTR\EARCORN\H1100E 4800114 BOLT\HEX\1/2X2 4900001 NUT\HEX\1/2\NC 5000004 WASH\FLAT\1/2 5000006 WASH\LOCK\1/2 4501053 AGTTR\EAR_CORN\KIT\H1130\H1100E\ DEALER_INSTALLED The Ear Corn Attachment is designed specifically for grinding ear corn.

  • Page 164: Geyser Plate (Option)

    G E Y S E R P L A T E ( O P T I O N ) H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 165 G E Y S E R P L A T E ( O P T I O N ) ITEM PART QTY. PART DESCRIPTION 4502642 FRM\PLFRM\TILT\1130\RTR\REAR 4502839 PL\GEYSER\9 BAR 4800010 BOLT\HEX\5/8X2 4900005 NUT\HEX\5/8\NC 5000002 WASH\FLAT\5/8 5000003 WASH\LOCK\5/8 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 166: Material Guide Assembly (Option)

    M A T E R I A L G U I D E A S S E M B L Y ( O P T I O N ) H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 167 M A T E R I A L G U I D E A S S E M B L Y ( O P T I O N ) ITEM PART QTY. PART DESCRIPTION 4501616 DEFL\GUIDE\MATL\CNVY\UPPR 4501617 GUIDE\MATL\CNVY\UPPR\24 4501618 BELT\GUIDE\MATL\CNVYR\UPPR 4800013 BOLT\HEX\5/16X1 4800559...

  • Page 168: Decals

    D E C A L S 6500020 6500118 6500440 H-1135 6500040 6500209 6500591 6500214 6500339 6500041 6500489 6500220 6500043 6500245 6500052 6500056 6500282 6500497 6500082 6500283 6500124 6500576 6500363 6500085 6500417 6500418 6500456 H - 1 1 3 5 T U B G R I N D E R...
  • Page 169 D E C A L S ITEM PART QTY. PART DESCRIPTION 6500020 DECAL\LOGO\HYBSTR\SNBRS\3 6500040 DECAL\WARN\SHIELD\PROT 6500052 DECAL\INFO\OIL;LEVEL 6500056 DECAL\INFO\ROTATION\STR 6500082 DECAL\WARN\ROTATN;PART;> 6500085 DECAL\DNGR\ROTATNG;DR-LNE 6500118 DECAL\DNGR\OBJCTS;THROWN 6500214 DECAL\WARN\OVRHED;CNVYR;> 6500215 DECAL\WARN\FOLDNG;CNVYR;> 6500245 8 ft. DECAL\TAPE\REFL\RED\WHT 6500339 DECAL\WARN\PINCH;POINT 6500363 DECAL\LOGO\BIGBITE\UNVRSL 6500417 DECAL\GREASE\10 HRS 6500418 DECAL\GREASE\10 HRS 6500432...

  • Page 170: Decal Locations

    D E C A L L O C A T I O N S 6500052 6500020 6500220 6500043 6500591 6500283 6500245 6500041 6500118 6500489 6500576 6500497 6500417 6500363 6500056 6500020 6500363 6500245 6500591 6500082 6500085 6500440 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 171 D E C A L L O C A T I O N S 6500082 6500056 6500040 6500043 6500209 6500124 6500282 6500040 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...
  • Page 172 D E C A L L O C A T I O N S 6500576 6500418 6500418 6500339 6500215 6500214 H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 173: H-1135 Tub Grinder Documentation Comment Form

    H-1135 Tub Grinder Documentation Comment Form DuraTech Industries welcomes your comments and suggestions regarding the quality and usefulness of this manual. Your comments help us improve the documentation to better meet your needs. • Did you find any errors? • Is the information clearly presented? • Does the manual give you all the information you need to operate the equipment safely and effectively? • Are the diagrams and illustrations correct?
  • Page 174 Please fill out the delivery report on the following pages. The white copy is to be returned to: DuraTech Industries International Inc. P.O. Box 1940 Jamestown, ND 58402-1940 The yellow copy is the dealer copy; the pink copy is to be retained by the customer. H - 1 1 3 5 T U B G R I N D E R P A R T S R E F E R E N C E...

  • Page 175: 5701174 - H-1135 Machine Harness

    5701174 - H-1135 MACHINE HARNESS H-1135 TUB GRINDER PARTS REFERENCE FO-1...

  • Page 176: 5701170-Pto Tub Tail Lights Harness

    5701170-PTO TUB TAIL LIGHTS HARNESS H-1135 TUB GRINDER PARTS REFERENCE FO-2...

Table of Contents