Subscribe to Our Youtube Channel
Related Manuals for Boss Snowplow BRX25175
Summary of Contents for Boss Snowplow BRX25175
- Page 1 Form No. MSC23905 Rev B Owner's Manual 48in Broom Kit Snowrator MAG Part No. BRX25175—Serial No. 400000000 and Up *MSC23905* Register at www.bossplow.com. Original Instructions (EN)
-
Page 2: Table Of Contents
g000502 Figure 2 Introduction 1. Safety-alert symbol The broom attachment is used to sweep walkways and driveways of dirt or snow. Read this information This manual uses 2 words to highlight information. carefully to learn how to operate and maintain your Important calls attention to special mechanical product properly and to avoid injury and product information and Note emphasizes general information... -
Page 3: Safety
Operation Safety • Never allow children or untrained people to operate Read and understand the contents of this manual the machine. Local regulations may restrict the before the engine is first started. age of the operator. The owner is responsible for training all operators and mechanics. -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decalmsc27245 MSC27245 1. Warning—stay away from moving parts; keep all guards and shields in place decal116-8140 116-8140... -
Page 5: Setup
Setup Positioning the Casters Rotate the caster-cap to remove from the shaft. Remove the caster assembly from the frame. Remove 1 or more spacers. g372001 Figure 4 Installing the Broom to the Machine Place the broom on a level floor with the kick stands in the down position;... - Page 6 Slowly move the machine towards the broom and raise the coupler upwards until the broom hooks onto the coupler. g371990 Figure 6 Rotate the coupler-pin 90° so that it engages g372115 Figure 8 with the broom assembly. Attach the motor hoses to the right side of the machine with the hook-and-loop fastener.
-
Page 7: Product Overview
Product Overview Controls g374196 Figure 12 Lower broom g370669 Figure 10 1. Angle lever 2. Attachment coupler lever g374197 Figure 13 Raise broom g374195 Figure 11 Float g372373 Figure 14 Right angle... -
Page 8: Operation
Operation Operating the Broom DANGER When the machine is in operation, contact with a rotating broom can result in serious personal injury to you or bystanders. • Before adjusting, cleaning, inspecting, troubleshooting, or repairing the machine, g372374 shut off the engine and wait for all moving Figure 15 parts to stop. -
Page 9: Using The Kickstands
Make sure that the area swept equals the length Align the kickstand handle with the hole in the of the broom and a maximum width of 51 to 102 kickstand and release the handle. mm (2 to 4 inches) as shown in Figure g372005 Figure 19... -
Page 10: Removing The Broom
Removing the Broom Operating Tips • Park the machine on a level surface, disengage Become familiar with the area being swept. the broom, move the motion-control levers to Hidden obstructions such as curbs and pipes can the N position, and engage the damage the broom and/or machine. -
Page 11: Maintenance
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Check the sweeping path. • Oil the chain. Before each use or daily • Check the hydraulic fluid. • Grease the caster wheels. Every 25 hours • Check the chain tension. Every 40 hours •... -
Page 12: Greasing The Caster Wheels
Park the machine on a level surface, disengage the broom, move the motion-control levers outward to the N position, and , EUTRAL engage the parking brake. Shut off the engine and remove the key. Lower the kickstands; refer to Using the Kickstands (page Remove the lynch pin. - Page 13 g371993 g371995 Figure 28 Figure 31 Remove the 4 carriage bolts (3/8 x 3/4 inch), Remove the bristles from the carrier. 4 nuts (3/8 inch), and side plate from broom Put new bristles on the carrier with the 2 pins assembly.
- Page 14 g371996 Figure 35 g400546 Figure 33 Install the 4 carriage bolts (3/8 x 3/4 inch), 4 nuts 1. Outer rings 2. Inner rings (3/8 inch), and side plate to broom assembly. Torque the 4 nuts to 41 N·m (30 ft-lbs). Install the 3 bolts (5/16 x 1-3/4 inches), 3 washers (5/16 inch), bushing, and retaining plate to the bristle carrier.
-
Page 15: Checking The Hydraulic Fluid Level
Storage Install the 5 carriage bolts (3/8 x 1 inch) and 5 nuts (3/8 inch) to the side bracket. Torque the 5 nuts from this step and 2 nuts from the previous Park the machine on a level surface, engage step to 41 N·m (30 ft-lbs). -
Page 16: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The broom does not clean the surface. 1. The broom height is incorrect. 1. Adjust the broom height. 2. The tire pressure in the drive tires is 2. Adjust the tire pressure in the drive not correct.
Need help?
Do you have a question about the BRX25175 and is the answer not in the manual?
Questions and answers