Advertisement
Available languages
Available languages
Quick Links
Before You Begin
UNPACKING
Unpack and carefully examine the product.
Report any damage and save all packing materials if any part(s) were damaged during shipping.
Do not attempt to install or use this equipment if it is damaged.
INCLUDED IN THIS BOX
LED fixture with U-bracket attached.
Installation instructions.
WARNING
– RISK OF FIRE, ELECTRIC SHOCK, INJURY, OR PROPERTY DAMAGE
Failure to follow these instructions or altering equipment could result in injury or damage and void warranty. Venture assumes no liability for
injury, damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling or use of this product.
This equipment must be installed and serviced per applicable codes and ordinances by qualified personnel (ex. licensed electrician) familiar with
the operation of the product and any hazards involved.
Disconnect power to the equipment and allow to cool before installing or servicing.
Handle sharp edges with care. To prevent wiring damage, do not expose wiring to sharp edges.
Verify that all electrical connections have been properly made and the fixture is grounded to avoid potential electrical shocks.
It is the installers responsibility to confirm the proper input voltage is used with the equipment.
Do not handle energized equipment when hands are wet, when standing on wet surfaces, or in water.
This fixture must be mounted securely to a structure to support the weight.
SUPPLIER'S DECLARATION OF CONFORMITY (SDoC)
This equipment complies with the limits for a Class A digital device, pursuant to Part 15 Subpart B of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a commercial, industrial or business
environment.
This equipment complies with the limits for a Class A lighting equipment, pursuant to Innovation, Science and Economic Development Canada's
CAN ICES-005 (A) / NMB-005 (A).
For warranty information refer to https://www.venturelighting.com/resources/warranties
IMPORTANT SAFETY INFORMATION
Operating temperature: -40°C to +50°C (-40°F to 122°F).
Suitable for use in wet locations.
All wiring and connectors used with this equipment shall be rated a minimum of 90°C (194°F)
Advertisement
Related Manuals for Venture Lighting Select-Pro FL58601
Summary of Contents for Venture Lighting Select-Pro FL58601
- Page 1 Before You Begin UNPACKING Unpack and carefully examine the product. Report any damage and save all packing materials if any part(s) were damaged during shipping. Do not attempt to install or use this equipment if it is damaged. ...
- Page 2 Installation Instructions – U-Bracket Disconnect power from the luminaire and follow proper lockout/tagout procedures before beginning installation or maintenance. Remove the existing luminaire (if present) and dispose of per local requirements. Remove clear knockout from back of fixture to gain access to dip switches. Dip switches are used to change wattage, color temperature, and to enable/disable photocell.
- Page 3 Connect the supply wires as shown in the wiring diagram below. NOTE: The correct polarity of the dimming connections is essential to proper operation. NOTE: If not using the dimming functionality, insulate the Dim(+) (purple) and Dim(-) (pink) wires separately (bare wires should not be left exposed). DO NOT connect the Driver Dim(+) (purple) to the Driver Dim(-) (pink) wire as the fixture will not operate correctly Close junction box, or similar, and restore power to the system.
-
Page 4: Avant De Commencer
Avant De Commencer LISEZ CES INSTRUCTIONS COMPLÈTEMENT ET ATTENTIVEMENT DÉBALLAGE Déballez et examinez soigneusement le produit. Signalez tout dommage et conservez tous les matériaux d'emballage si des pièces ont été endommagées pendant le transport. N'essayez pas d'installer ou d'utiliser cet équipement s'il est endommagé. ... - Page 5 Instructions d'installation – U-Bracket Débranchez l'alimentation du luminaire et suivez les procédures de verrouillage/étiquetage appropriées avant de commencer l'installation ou la maintenance. Retirez le luminaire existant (le cas échéant) et jetez-le conformément aux exigences locales. Retirez la découpe transparente à l'arrière du luminaire pour accéder aux commutateurs DIP. Les commutateurs DIP sont utilisés pour modifier la puissance, la température de couleur et pour activer/désactiver la cellule photoélectrique.
- Page 6 Connectez les câbles d'alimentation comme indiqué dans le schéma de câblage ci-dessous. REMARQUE: La polarité correcte des connexions de gradation est essentielle au bon fonctionnement. REMARQUE: Si vous n'utilisez pas la fonctionnalité de gradation, isolez les fils Dim(+) (violet) et Dim(-) (rose) séparément (les fils dénudés ne doivent pas être laissés exposés).