Correct Positioning
NaviLED
360 Compact All Round / Anchor
®
Lamps must be installed as follows:
When the lamp operates, the light should not
be obstructed or concealed by masts,
topmasts or structures, i.e. Installed on the
highest point of a vessel so the light arc is
unbroken.
All Round lamps must be positioned as close
as practicable to the fore and aft centre line
of a vessel. (see Fig.1)
The All Round white lamp on a power driven
Vessel less than 12m in length shall be
installed at least one meter higher than the
sidelights.
The lamp must be installed so that the
horizontal surface of the base is parallel to
the vessel's water line. (See Fig.2)
Mounted with
h
swivel bracket
et
Installation Instructions
Mounted with
Mounted with
1. Fixed Pole mount: Ensure mounting surface is flat and on the vessels centre line (see above).
plug-in bracket
plug-in bracket
Use the provided screws to secure taking care not to over tighten.
Ø 3mm
Ø 3mm
2. Fold-down Pole mount: A removable wedge is supplied for installations onto different surface
cambers. Use the provided screws to secure taking care not to over tighten. Once mounted the
base can be adjusted through 180 degrees, when the desired angled is reached secure by
tightening the locking collar.
3. Plug-in Pole mount: Mount base separately and connect wiring. Use the provided screws to
secure taking care not to over tighten. Insert lamp into base and fix with locking collar.
Ensure rubber cap, as provided, is used to cover socket when pole is removed.
Ø 3mm
Ø 3mm
Mounted with tel-
MAX 3 Nm
escope bracket
Mounted with tel-
escope bracket
Ø 3mm
1. Fixed pole
Mounted with
Mounted with
standard bracket
standard bracket
Fig. 1 On the fore and aft centre line.
Fore
Aft
Fig. 2
Installed with base parallel to vessel's
water line.
2010 series lamps Mounting Instructions
2010 series lamps Mounting Instructions
Mounted with
swivel bracket
The Hella marine Series 2010 navigation and signal lamps comply with USCG A-16 requirements for
The Hella marine Series 2010 navigation and signal lamps comply with USCG A-16 requirements for
powerboats and/or sailing vessels up to 12 m (39') in length.
powerboats and/or sailing vessels up to 12 m (39') in length.
Vessel's water Line
Mounting position of the lamps:
Mounting position of the lamps:
- Port and starboard navigation lamps (3) must be mounted with their back plate parallel to the vessel
- Port and starboard navigation lamps (3) must be mounted with their back plate parallel to the vessel
Mounted with
plug-in bracket
centre line (6), in the same thwartships position (5) and at the same height above the waterline (4).
centre line (6), in the same thwartships position (5) and at the same height above the waterline (4).
- Masthead (1) and stern lamps (2) as well as anchor lights must be mounted above the vessel centre
- Masthead (1) and stern lamps (2) as well as anchor lights must be mounted above the vessel centre
line (6).
line (6).
Ø 3mm
- All lamps must be mounted in a vertical position with their back plate perpendicular to the waterline.
- All lamps must be mounted in a vertical position with their back plate perpendicular to the waterline.
- When operating, the light should not be obstructed or concealed by superstructures, other objects or
- When operating, the light should not be obstructed or concealed by superstructures, other objects or
Ø 3mm
persons. The lamps should also be tightly secured in position
persons. The lamps should also be tightly secured in position
Ø 3mm
MAX 3 Nm
(1) Masthead lamp (white)
(1) Masthead lamp (white)
(2) Stern lamp (white)
(2) Stern lamp (white)
(3) Starboard / port lamp
(3) Starboard / port lamp
(4) Waterline (CWL)
(4) Waterline (CWL)
(5) Thwartships plane
(5) Thwartships plane
(6) Vessel centre line
(6) Vessel centre line
(7) green
(7) green
(8) red
(8) red
(9) white
(9) white
Ø 3mm
Mounted with
Maintenance
Maintenance
standard bracket
-
The lens may be cleaned with a soft brush.
-
The lens may be cleaned with a soft brush.
2. Fold-down pole
3. Plug-in pole
-
Only cleansers suitable for polycarbonate plastic may be used.
-
Only cleansers suitable for polycarbonate plastic may be used.
-
Do not wash with harsh or abrasive cleaners.
-
Do not wash with harsh or abrasive cleaners.
INSTRUCTION SHEET: NaviLED
Hella marine LED Navigation Lamps offer many advantages over conventional bulb lamps.
Significantly reduced power consumption, ultra long life and high tolerance to shock and
vibration make the LED lamps the ideal choice for the harsh marine environment.
The Hella marine NaviLED
approved to comply with international maritime regulations. They are covered by a 5 year
warranty.
Product Specifications
Housing Material
Lens Material
2010 series lamps Mounting Instructions
Minimum Visible Distance
The Hella marine Series 2010 navigation and signal lamps comply with USCG A-16 requirements for
Cable
powerboats and/or sailing vessels up to 12 m (39') in length.
Operating Voltage
Mounting position of the lamps:
Power Consumption
- Port and starboard navigation lamps (3) must be mounted with their back plate parallel to the vessel
Degree of Protection
centre line (6), in the same thwartships position (5) and at the same height above the waterline (4).
- Masthead (1) and stern lamps (2) as well as anchor lights must be mounted above the vessel centre
Approvals
line (6).
- All lamps must be mounted in a vertical position with their back plate perpendicular to the waterline.
- When operating, the light should not be obstructed or concealed by superstructures, other objects or
Ø 3mm
persons. The lamps should also be tightly secured in position
Electromagnetic Compatibility (EMC)
This LED lamp is an electronic device. The electrical circuits contain components that suppress
possible interference, both emission as well as susceptibility, to the limits prescribed in
international regulations.
*
*
) Angle of 7.5 °
) Angle of 7.5 °
(25° for sailing vessels).
(25° for sailing vessels).
(1) Masthead lamp (white)
(2) Stern lamp (white)
(3) Starboard / port lamp
(4) Waterline (CWL)
MAX 3 Nm
(5) Thwartships plane
(6) Vessel centre line
Wiring and Electrical Protection
(7) green
(8) red
LED modules are polarity conscious. This lamp is protected against reverse polarity connection,
(9) white
reverse polarity will not damage this product but will inhibit its function.
HELLA marine recommends wire connections be soldered, and heat shrink tubing applied to seal
Ø 3mm
the joint.
Maintenance
Each lamp must be protected against short circuit by a fuse rated at 5 amperes maximum.
-
The lens may be cleaned with a soft brush.
-
Only cleansers suitable for polycarbonate plastic may be used.
Note: Do not attempt to open, no serviceable part inside.
-
Do not wash with harsh or abrasive cleaners.
993 609-00
360 Compact Pole Mount
®
2 Nautical Mile All Round White / Anchor Lamp
360 series are Precision Optical Instruments, tested and type
®
UV resistant high impact plastic
Heavy duty Grilamid
2 Nautical Miles
Pre-wired with twin core marine cable
Multivolt
9-33V DC
TM
Less than 1W (0.08A @ 12V / 0.04A @ 24V)
IP 67 - Completely Sealed
USCG, IMO COL REG 72, Wheelmark
*
Wiring Colour Coding
) Angle of 7.5 °
(25° for sailing vessels).
Colour
Connect to
Black
Negative (-ve)
Red
Signal (+ve)
993 609-00
Designed and Manufactured in New Zealand
993 609-00
®
Need help?
Do you have a question about the NaviLED 360 and is the answer not in the manual?
Questions and answers