Maintenance And Care - Schumacher Electric INSTANT POWER XP750C Owner's Manual

USING THE USB PORT
The USB port provides up to 2A
at 5V DC.
1. Ensure the battery clamps are
securely clipped on the storage
holders.
2. Turn the Instant Power ON.
3. Plug your device into the USB port.
4. When finished using the USB port,
turn the switch to the OFF position.
5. Charge the Instant Power.
USING THE WORK LIGHT
The work light is controlled by a sliding
ON/OFF switch located on the front of
the Instant Power. Make sure the lamp
is turned OFF when the unit is being
recharged or stored.
Position the Instant Power on a flat, stable
surface near the intended work area.
Ensure the battery clamps are securely
clipped on the storage holders.
POWERING A 12V DC DEVICE
The Instant Power is a power source for
all 12V DC accessories that are equipped
with a 12V accessory plug. Use it for power
outages and on fishing or camping trips.
NOTE: Do not power a 12V device with
the Instant Power while charging the
internal battery.
1. Make sure the device to be powered
is OFF before inserting the 12V DC
accessory plug into the 12V DC
accessory outlet.
2. Open the protective cover of the DC
power outlet on the Instant Power.
3. Plug the 12V DC device into the DC
power outlet and turn on the 12V DC
device (if required).
4. When finished, turn off the DC device
(if required) and unplug from the DC
power outlet.
CAUTION: Do not use the Instant Power
to run appliances that draw more than
15A DC.
NOTE: Extended operation of a 12V DC
device may result in excessive battery
drain. Recharge the Instant Power
immediately after unplugging the 12V
DC device.

6. MAINTENANCE AND CARE

• Clean the clamps and the case each time
you are finished using it.
• Recharge the unit once a month when
not in use.
Estimated run-times
APPLIANCE TYPE
Cell phone
Fluorescent light
Radios, fans
Depth finder
Camcorder
Electrical tool
Electric cooler
Car vacuum, air compressor
NOTE: Actual time may vary. Times are based
on the internal battery being fully charged.
USING THE AIR COMPRESSOR
WARNING. Read the instructions of the
product being inflated before using the
compressor. Avoid overinflation; do not
exceed the manufacturer's recommended
pressures. Do not leave the air
compressor unattended during use.
NOTE: Wrap cleats are provided for
convenient storage of the air compressor
hose. Wrap the hose around these cleats
when the hose is not in use.
1. Remove the air compressor hose from
the storage cleats.
2. Connect the adapter to the valve
stem by threading it onto the end. If
necessary, use one of the additional
adaptors.
3. Press the air compressor power
switch to turn ON and inflate to the
desired pressure or fullness (refer to
the gauge next to the switch).
4. When the desired pressure is
reached, press the air compressor
power switch to turn OFF and remove
the connector from the valve stem.
5. Allow unit to cool.
6. Recharge the unit before storing.
NOTE: The air compressor is rated for
150 PSI.
Estimated time for inflating
Vehicle tires 13-16"
Bike tires
Sports balls
These times are approximate. Use the air
compressor gauge to ensure the proper
pressure has been reached. Do not overinflate.
• Store clamps on their support posts, to
ensure they do not come into contact
with any metallic surface.
• Never completely discharge the internal
battery.
EST XP750C
WATTAGE XP750W
4 watts 34 hrs
4 watts 34 hrs
9 watts 14 hrs
9 watts 14 hrs
15 watts 7 hrs
24 watts 5 hrs
48 watts 2 hours
80 watts 1.8 hrs
6-24 minutes
1-3 minutes
30 seconds