Megxon TX520 Quick Start Manual

1. R9000094 2.
165mm+-2
Quick Start Guide
Safety Notes
Do not try to open the camera by yourself which may cause damage to the camera or electric shock.
Do not fire the flash in a close distance (less than 1 meter) to human eyes.
Keep the camera away from the reach of children or animals to prevent them from swallowing the batteries or small accessories.
Avoid using the camera if any form of liquid enters the camera. If it happens, switch off the camera and contact the company that you
bought this camera from for help.
Do not operate this camera with wet hands which may cause electric shock.
Do not place or store the camera in a high temperature environment which may cause damage to the camera.
Do not mix to use different types of batteries or new and old batteries.
Take out the batteries to avoid electricity leakage which may damage the camera when the camera is not in use for a long period.
Unplug the camera from the adapter (if used) to avoid damage to the camera if the camera is not to be used in a long period.
It's normal that the temperature of the camera body rises after using for a long period.
1 1 1
Icon Introduction Icon Introduction
3 2 1
Working Mode
Focus Range
0006
1
13
Flash Modes
X4
12
4 X4
Digital Zoom
X1 X1
11
Thumbnails
5
10
2003/10/30
+0.5
6 Self-timer
Movie Clip
7 8 9
Memory Card Inside
1 Photo Frame 6 Battery Status 11 Image Quality
Battery Status
( )Battery full ( )Super fine
( )Battery half ( )Fine
Image Size (Resolution)
2 Voice Memo drained ( )Normal
( )Battery
drained Image Quality
3 Working Mode 12 White Balance
White Balance AUTO
( )Auto
( )Shooting mode AUTO
7 Memory Card - +
( )Playback mode ( )Daylight Exposure 0
( )Movie clip mode ( )Sunset
( )Setup mode ( )Fluorescent
8 Exposure Voice Memo
( )Tungsten
Protected Image
4 Digital Zoom 9 Date
Print (DPOF)
13 Flash Mode
( )Auto flash
5 Focus Range 10 Image Size ( )Auto flash with Darkness Warning
( )Macro ( )2560x1920
red-eye
Photo Frame 1 2
( )2048x1536 reduction
( )1600x1200 ( )Slow Sync
Processing
( )1280x960 ( )Flash off
4 4 4
Pantone 282C 3.
165mm+-2
Getting Ready
Switch On or Off the Camera
Slide the "POWER" switch sideways and hold it awhile to switch on the camera.
Repeat the action above to switch off the camera.
Loading the Batteries
Inserting or Removing an SD Card
PC Connection
Installing the Camera's Driver
Please refer to the User Manual for the details.
Installing Ulead Photo Explorer
Please refer to the User Manual for the details.
Downloading the image(s)
Please refer to the User Manual for the details.
3
80P
Getting Started
Basic Photography
1.Switch on the power.
2.Set the Mode Dial at Shooting Mode (
3.The setting of the focus range for still image capture is required as follows
Macro (
Normal (
4.Refer to the User Manual -- Advanced Functionality Settings (page10)to set up the features based on your needs.
5.Hold still and press down the Shutter Button.
6.The LED Indicator starts blinking right after the Shutter Button is released.
7.Once the LED Indicator stops blinking, you are ready to take another shot.
1. Check if the camera is switched off.
Note
2. Slide the Battery / Memory Card Cover out to open it.
A message of "Low Light!" appearing on the TFT LCD Monitor as a warning is to remind you that the image that you are going to
3. Load 2 x AA batteries into the battery chamber, following the
capture is under a low light environment. To compose a good quality image, it is strongly recommended to go to the Flash Mode and
polarity indication.
select Auto Flash to supply more light sources.
4. Close the Battery / Memory Card Cover.
1
1. Switch off the camera.
2. Open the Battery / Memory Card Cover.
3. Insert the SD card into the card slot and press it down until a click
sound happens.
4. Close the Battery / Memory Card Cover.
2 2
Error Message Table Error Message Table
Messages
CARD FULL
MEMORY FULL
CARD LOCKED
(ICON BLINKING)
LOCK
NO IMAGE
FILE ERROR
MEMORY ERROR
CARD ERROR
LOW BATTERY !
(ICON BLINKING)
HAND SHAKE
ICON (
5 5
165mm+-2
) for still image or Movie Clip Mode ( ) for video recording.
) : 0.3m
): 1.4m~infinity
2 2 3 3 4 4
3 3
Causes Solutions
There is insufficient card memory capacity Delete the stored image(s) in the memory
to store an image.
card or insert a new memory card.
There is insufficient internal memory Delete the stored image(s) in the flash
capacity to store an image. memory.
The SD card is under protection. Set the card protection switch at non-
protection position.
The Image can't be deleted under protection. Unlock the protected image.
There is no image stored in the memory card Please take pictures or record movie
or built-in flash memory. clips.
File format error. Insert a new SD/MMC card or
format the media.
Memory is damaged or failed. Format the media.
Card is damaged or failed. Insert a new SD/MMC card
Battery power is drained. Insert new batteries.
The environment is too dark in "Flash Off" Cancel the Flash off mode.
) mode.
R9000094
6 6