Insignia NS-LGLT1000P531 Quick Setup Manual

QUICK SETUP GUIDE
Refrigerator
Filter
NS-LGLT1000P531
Before using your new product,
please read these instructions to prevent any damage.

PACKAGE CONTENTS

• Refrigerator water filter
• Quick Setup Guide

COMPATIBILITY

Works with LG® and Kenmore®
refrigerator models:
LMXS30796S,
LMXS30796D, LMXC23796S, LMXC23796D,
LFXS30796S, LFXS30796D, LMXS28626D,
LFXC24796D, LFXC24796S, LSXC22396S,
LSXS26396S, LSFXC2496D, LSXC22396D,
LMXS28626S, LFXS28968, LMXS28626,
LFXS28566, LMXS28636, LFXS28968S,
LFXS28566M, LMXS28636S, LFXS28968D,
LFXS28566S, LFXS28566D, LSFXC2496S,
LFXC22596S, LFXS26596M, LFXS28596D,
LFXS26566M, LFXS26973D, LFCC22426S,
LFXC22526S, LFCS28768S, LSXS26336S,
LFXS26566S, LFXS26973S, LFXS26596S,
LFXS28596M, LFXS28596S, LMXC23796M,
and LFXS27466S

FEATURES

• NSF 42 and 53 certified to remove contaminants, including chlorine, cysts, lead,
mercury, carbofuran, benzene, and endrin
• Lasts up to six months or 200 gallons (757 L)
• Eliminates cloudiness for fresh, clear drinking water

INSTALLING YOUR WATER FILTER

1 Shut off the water supply, then turn off the water shutoff valve on your
refrigerator. Locate the filter holder in your refrigerator.
Side door filter:
2 Lift up and remove the lower bin
door.
3 Swing the right end of the old
filter out of the compartment
and then hold and rotate the
filter counterclockwise to
remove it from the filter head.
4 Insert the new filter into the
filter head and rotate it
clockwise.
5 Swing the filter back into the
compartment.
6 Replace the lower bin door.
7 Turn on the the water supply and run water through the dispenser for about five
minutes at 0.5 gpm (about 2.5 gallons or 9.5 L) to remove any trapped air and clear
the system.
CAUTION: This filter should not be used with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system.
8 Open the refrigerator door and make sure that no water leaks from the new filter.
Note: If leaks occur, repeat the installation steps. If leaks persist, discontinue use and call
customer service.
WARNING: To reduce the risk of property damage due to water leakage, this filter MUST be
installed in accordance with the manufacturer's specifications and instructions. This filter unit
must be replaced every 200 gallons (757 L) or six months. Failure to follow instructions and
operating specifications will void your warranty. Further, manufacturer assumes no
responsibility or liability for damages arising out of misuse of the product.

RESETTING YOUR CHANGE FILTER INDICATOR

• LG: Press and hold the reset button for three seconds. If this doesn't work, see the
documentation that came with your refrigerator.
• Kenmore: The filter reset for Kenmore refrigerators varies by model. See the
documentation that came with your refrigerator.
Upper corner filter:
OR
2 To open the filter cover, push in
where indicated and the cover will
drop down.
3 Remove the old filter by slowly
rotating it counterclockwise. A
small amount of water may drip
down.
4 Insert the new filter into the water
filter holder.
5 Slowly turn the new filter clockwise
until it stops. The filter will click and
lock into place.
6 Close the filter cover.