Omnitron Systems iConverter 8245-11pt User Manual

1-module redundant power chassis

Advertisement

Quick Links

iConverter
1-Module Redundant Power Chassis
User Manual
38 Tesla, Irvine, CA 92618 USA
Phone: (949) 250-6510
®
General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights reserved.
The whole or any part of this publication may not be reproduced, stored in a retrieval
system, translated, transcribed, or transmitted, in any form, or by any means, manual,
electric, electronic, electromagnetic, mechanical, chemical, optical or otherwise, without
prior explicit written permission of Omnitron Systems Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.: FlexPoint
FlexSwitch
, HybridNID
, iConverter
TM
®
OmniConverter
, RuggedNet
, Omnitron Systems Technology, Inc.
®
®
Omnitron logo.
All other company or product names may be trademarks of their respective owners.
The information contained in this publication is subject to change without notice.
Omnitron Systems Technology, Inc. is not responsible for any inadvertent errors.
Warranty
This network product and the included AC/DC power adapter are warranted to the
original purchaser (Buyer) against defects in material and workmanship for a period of
two (2) years from the date of shipment. The warranty for the network product can be
extended to lifetime by registering the product at www.omnitron-systems.com/support
within ninety (90) days from the date of shipment. During the warranty period, Omnitron
will, at its option, repair or replace a product which is proven to be defective with the
same product or with a product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility, at
Buyer's expense. Omnitron will pay the shipping charge to return the product to Buyer's
designated US address using Omnitron's standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to product malfunctions resulting from improper
or inadequate use and/or maintenance of the equipment by Buyer, Buyer-supplied
equipment, Buyer-supplied interfacing, unauthorized modifications or tampering
with equipment (including removal of equipment cover by personnel not specifically
authorized and certified by Omnitron), or misuse, or operating outside the environmental
specification of the product (including but not limited to voltage, ambient temperature,
radiation, unusual dust, etc.), or improper site preparation or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
The remedies provided herein are the Buyer's sole and exclusive remedies. Omnitron
shall not be liable for any direct, indirect, special, incidental, or consequential damages,
whether based on contract, tort, or any legal theory.
Environmental Notices
The equipment covered by this manual must be disposed of or recycled in accordance
with the Waste Electrical and Electronic Equipment Directive (WEEE Directive) of
the European Community directive 2012/19/EU on waste electrical and electronic
equipment (WEEE) which, together with the RoHS Directive 2015/863/EU, for electrical
and electronic equipment sold in the EU after July 2019. Such disposal must follow
national legislation for IT and Telecommunication equipment in accordance with the
, miConverter
, NetOutlook
, OmniLight
®
TM
®
, OST
TM
TM
Page 2
,
TM
,
®
and the

Advertisement

Table of Contents
loading

Summary of Contents for Omnitron Systems iConverter 8245-11pt

  • Page 1 Omnitron Systems Technology, Inc. The following trademarks are owned by Omnitron Systems Technology, Inc.: FlexPoint FlexSwitch , HybridNID...
  • Page 2: Customer Support Information

    Power Calculator to verify the iConverter chassis power supplies will meet the requirements of the installation. Address: Omnitron Systems Technology, Inc. Backplane Architecture 38 Tesla Irvine, CA 92618, USA The chassis features two Ethernet backplane buses (A and B) that operate at 10/100Mbps.
  • Page 3: Wall And Rack Mounting

    AC Powered Chassis and Cabling Secure the ground wire to the ground screw (located on the rear of the chassis). To power the module using the included AC power adapter, route the power cord through the provided strain relief (depending on the model) for additional support. Connect the barrel connector at the end of the wire on the AC/DC adapter to the barrel connector on the module.
  • Page 4 The over current protection for the connection with centralized DC shall be provided in the building installation and shall be a UL listed breaker rated at 20 Amps, and installed per the National Electrical Code, ANSI/NFPA-70. This equipment requires 20-60VDC/0.6Amp rated power. Appropriate overloading protection should be provided on the DC power source outlets utilized.
  • Page 5 WARNING!!! WARNING REGARDING EARTHING GROUND: NEVER ATTEMPT TO OPEN THE CHASSIS OR This equipment shall be connected to the DC supply SERVICE THE POWER SUPPLY. OPENING THE system earthing electrode conductor or to a bonding jumper from an earthing terminal bar or bus to which the CHASSIS MAY CAUSE SERIOUS INJURY OR DEATH.
  • Page 6: Led Indicators

    Contact Closure Sensors The 8-pin connector has the following pin configuration: On models with the contact closure sensor feature, the chassis provides an optional Pin # Description Closed Open 8-pin connector (4 contact sensors) on the back of the chassis that can be used to sense Sensor 1 “+”...
  • Page 7 Serial Console Port on Installed Management Module Applications To configure the module using the serial port, attach a DB-9 serial (RS-232) equipped Battery Backup with Alarms computer with terminal emulation software such as Procomm or Putty to the serial port When the chassis is used with a battery backup power system, the alarm contact on the module using the included serial adapter.
  • Page 8: Specifications

    Contact Closure Sensor Configuration Specifications The contact closures can be used to alert the network management system of problems iConverter Description 1-Module Redundant Power Chassis associated with the remote location. The contact closure sensor can also detect the Standard IEEE 802.3, 802.3af opening and closing of a switch, such as a equipment door being opened or closed.

This manual is also suitable for:

Iconverter 8246-11ptIconverter 8246-51ptIconverter 8247-11ptIconverter 8247-12ptIconverter 8247-220tIconverter 8247-31pt ... Show all

Table of Contents