Before Using The Machine - EINHELL TE-MB 18/127 Li Original Operating Instructions

Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Handle
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Anl_TE_MB_18_127_Li_SPK13.indb 20 Anl_TE_MB_18_127_Li_SPK13.indb 20
< 2.5 m/s
2
h
2
- 20 -
GB

5. Before using the machine

Warning!
Always remove the battery before making adjust-
ments to the machine.
5.1 General information
•
Warning! Before you use the machine for the
first time, tension the blade (15) (see 5.5).
•
All covers and safety devices must be proper-
ly fitted before the machine is switched on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been previ-
ously processed, watch out for foreign bodies
such as nails or screws, etc.
•
Before you actuate the On/Off switch, make
sure that the blade is correctly fitted and that
the machine's moving parts run smoothly.
•
Important! The two hex keys (22/23) are
stored in the adjustable handle (10) (see Fig.
2).
•
Important! Please note that the tooth pitch of
the blade you are using must match the mate-
rial you want to cut. In the case of particularly
hard materials or particularly large depths
of blade penetration you should change the
tooth pitch by changing the blade.
5.2 Adjusting the handle (Fig. 3)
•
The adjustable handle (10) can be fastened
in various locking positions according to re-
quirements.
•
Release the clamping lever (11).
•
Place the adjustable handle (10) in the requi-
red position.
•
Lock the setting by refastening the clamping
lever (11).
•
Important! You can adjust the pretension of
the clamping lever (11). To do so, hold the
released clamping lever (11) firmly and adjust
the nut (12) on the opposite side (clockwise:
higher tension). Check the setting by closing
the clamping lever (12) again. Keep repeating
until you have the required tension.
5.3 Adjusting the workpiece stop (Fig. 4)
•
Important! The workpiece stop (13) is set at
the factory to the top position.
•
Important! Set the workpiece stop (13) to the
lowest position as this will increase the size
of the guide face. Set the workpiece stop to a
higher position only in exceptional cases.
•
Slacken the two socket head screws (14)
with the hex key (22) in order to be able to
13.09.2022 14:38:57 13.09.2022 14:38:57