GS2/MV Basic Wall Mount Remote Installation with AC Adapter SKU# 99300696 Warnings The transmitter and receiver are radio frequency devices. Placing the transmitter in or near metal may severely reduce the signal range. Turn off power to the heater during installation or maintenance (unplug or turn off at the breaker).
GS2/MV Basic Wall Mount Remote Installation with AC Adapter SKU# 99300696 Overview This kit supplies a basic wall-mount remote kit with an AC adapter to power the remote receiver. The basic installation is the same for MV and GSB stoves and inserts. This kit can also be used with MV and GSB fireplaces however, the way the kit connects to AC power is slightly different than with the inserts and stoves (see fireplace installation section for details).
Page 4
GS2/MV Basic Wall Mount Remote Installation with AC Adapter SKU# 99300696 RADIANT STOVE NOTE: If a blower is being uesd, install the blower kit first and discard the power cord and strain relief bracket from this kit. With the blower kit installed follow the steps below to electricly ground the accessories to the appliance belly pan.
Page 5
GS2/MV Basic Wall Mount Remote Installation with AC Adapter SKU# 99300696 2. Install the power cord with a strain relief clamp into the bracket. Feed the Molex end of the power cord through the hole in the bracket. Close to the end of the wire insulation place the strain relief on the wire with the sloped end facing the plug end of the cord.
Page 6
GS2/MV Basic Wall Mount Remote Installation with AC Adapter SKU# 99300696 4. Connect the green and white wires to the corresponding On/Off switch wires. 5. Connect the blue and white wires from the back of the receiver to the AC adapter. The insulation that covers the quick connects on the AC adapter are different colors.
GS2/MV Basic Wall Mount Remote Installation with AC Adapter SKU# 99300696 Steps Specific to MV Fireplace and Insert Installation This set of installation instructions shows a summary of the remote installation. For detailed instructions on the placement of the receiver and other details, refer to the installation manual included with your appliance.
GS2/MV Basic Wall Mount Remote Installation with AC Adapter SKU# 99300696 Steps Specific to MV Stove Installation This set of installation instructions shows a summary of the remote installation. For detailed instructions on the placement of the receiver and other details, refer to the installation manual included with your appliance.
GS2/MV Basic Wall Mount Remote Installation with AC Adapter SKU# 99300696 Steps Specific to GSB2 Installation This set of installation instructions shows a summary of the remote installation. For detailed instructions on the placement of the receiver and other details, refer to the installation manual included with your appliance.
See the installation instructions for details. These batteries power the receiver. The batteries also act as a power backup in case the household (AC) current goes out (GSB2 units only). Page 12 of 18 17602250 - 10/7/22 Travis Industries, Inc.
REMOTE – Fireplace is controlled by the transmitter. Figure 4 NOTE: When the receiver switch is turned to ON or OFF, the thermostat and burner on/off operating functions will not work on the transmitter. Page 13 of 18 17602250 - 10/7/22 Travis Industries, Inc.
NOTE: When the batteries start to get low, the IFC will beep intermittently. When the batteries are nearly depleted, the IFC will no longer beep. See “Receiver Batteries” on page 16). Page 14 of 18 17602250 - 10/7/22 Travis Industries, Inc.
Page 15
Use the up or appear here. down buttons to adjust the target temperature. NOTE: If the transmitter batteries go dead while in thermostat setting, the appliance will shut off after approximately 24 hours. Page 15 of 18 17602250 - 10/7/22 Travis Industries, Inc.
Display Fahrenheit or Celsius With the system in the “OFF” position, press both the MODE and THERMOSTAT buttons simultaneously to toggle between Fahrenheit (F) and Celsius (C). Page 16 of 18 17602250 - 10/7/22 Travis Industries, Inc.
Repeat this process to toggle the thermostat function to the desired setting. When "SET" appears, the thermostat function is enabled. When "CLR" appears, the thermostat function is disabled. Page 17 of 18 17602250 - 10/7/22 Travis Industries, Inc.
Press the "up" button to activate ("SET") the mode selected. Press the "down" button to clear ("CLR") the mode selected. Release the on/off button to complete programming. Page 18 of 18 17602250 - 10/7/22 Travis Industries, Inc.