Specification - HOGERT HT4R651 User Manual

EN
USER'S MANUAL
AIR SANDER RANDOM ORBITAL HT4R651
Thank you for purchasing our Product. Manufactured to a high standard this product will,
if used according to these instructions andproperly maintained, give you years of trouble
free performance.
WARNING IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE
SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT
IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FU-
TURE USE.
1. 1. SAFETY
Follow all workshop Health & Safety rules, regulations, and conditions when using tool
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered
to when using this equipment.
WARNING! Disconnect from air supply before changing accessories or servicing.
- Maintain the sander in good condition (use an authorised service agent).
- Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and
will invalidate the warranty.
- Use in suitable clean and tidy working area, free from unrelated materials and ensure there is adequate lighting.
- Before each use check abrasive discs and backing pads for condition. If worn or damaged replace immediately.
- Ensure the backing pad rating is the same as, or, greater than the RPM rating of the sander.
- Ensure there are no flammable or combustible materials near the work area.
WARNING! Always wear approved eye or face and hand protection when operating the sander.
- Use face, dust, or respiratory protection in accordance with COSHH regulations.
- Depending on the task, sander noise level may exceed 85dB in which case wear safety ear defenders.
- Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery, and contain and/or tie back long hair.
- Wear appropriate protective clothing and keep hands and body clear of working parts.
- Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
- Keep children and unauthorised persons away from the working area.
- Check moving parts alignment on a regular basis.
- Ensure workpiece is secure before operating the sander. Never hold a workpiece by hand.
- Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
- Avoid unintentional starting.
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90PSI.
- Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
- Prolonged exposure to vibration from this sander poses a health risk. It is the operator's responsibility to correctly
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
- DO NOT use the sander for a task it is not designed to perform.
- DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
WARNING! DO NOT sand any materials containing asbestos.
- DO NOT carry the sander by the hose, or yank the hose from the air supply.
- DO NOT force, or apply heavy pressure to the sander, let the sander do the work.
- DO NOT place attachments close to your face and do not point at other persons or animals.
- DO NOT operate sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.
- DO NOT use sander where there is flammable liquids, solids or gases such as paint solvents and including
waste wiping or cleaning rags etc.
- DO NOT carry the sander with your finger on the power lever.
- DO NOT direct air from the air hose at yourself or others.
- When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION
Durable, lightweight body with moulded handle, reducing chill effects and providing extra control.
Fitted with dual exhaust ports and air control valve. Supplied with Ø150mm hook-and-loop pad.
Ideal for the DIY enthusiast and light garage use.

3. SPECIFICATION

Model no:
thread Size:
Free Speed:
Adres producenta/ Adresse des Herstellers/ Manufacturer's Address/ Адрес производителя
GTV Poland Sp. z o.o. Sp. k., ul. Przejazdowa 21, 05-800 Pruszków
HT4R651
5/16" UNF
1000 rpm
9