Page 3
User Guide abcdefg The Quality Management System of Land Instruments International Ltd. is approved to BS EN ISO9001:2000 for the design and manufacture, stockholding, in-house repair and site servicing of non contact temperature measuring instrumentation. Associated software designed and developed in accordance with TickIT.
Page 4
User Guide SAFETY INFORMATION SYMBOL PUBLICATION DESCRIPTION Direct IEC 417, No.5031 Current Alternating IEC 417, No.5032 Current Both direct and alternating IEC 417, No.5033 current Three-phase alternating IEC 617-2, No.02-02-06 Current Earth IEC 417, No.5017 (ground) terminal IEC 417, No.5019 Protective conductor terminal IEC 417, No.5020 Frame or chassis terminal...
Page 5
User Guide SAFETY INFORMATION (Continued) SYMBOL PUBLICATION DESCRIPTION WARNING Risk of electric shock ISO 3864, No. B.3.6 Caution ISO 3864, No. B.3.1 Observe precautions for BS EN 100015 handling electrostatic discharge sensitive devices WARNING BS EN 60825-1 Laser Radiation Refer to the operating instructions Note Safety Information...
User Guide CONTENTS QUALITY ASSURANCE SAFETY INFORMATION CONTENTS (This Page) PREFACE INTRODUCTION Nomenclature Specifications INSTALLATION Introduction Positioning The Scanner Alignment And Scan Direction Installation Precautions SERVICES Electrical Connections Water Requirements (Water Cooled Units Only) Air Requirements (Air Purged / Cooled Units Only) LASER ALIGNMENT Using The Laser Alignment Tool EMISSIVITY...
Page 8
User Guide CONTENTS (Continued) INTERNAL TEMPERATURE SENSOR Introduction MAINTENANCE Air Purge Services Water And Air Cooling Services INSTALLATION ACCESSORIES Basic Mounting Plate Right Angle Mounting Bracket Water Cooled, Air Purge Baseplate Kit Water Cooled End Plate Kit Air Cooled End Plate Kit Contents 198.240...
Page 9
User Guide PREFACE 240001 Fig. A - LSP Linescanning Thermometer These instructions cover installation, operation and maintenance of the LSP Linescanning Thermometer and should be used in conjunction with the information detailed within the LSP Linescanning Thermometer Installation Guide, LSP Processor Installation Guide and User Guide and the LSP System Mountings and Accessories Installation Guide.
User Guide INTRODUCTION The LANDSCAN LSP SYSTEM provides accurate linescan temperature measurement at high scan rates. This is achieved through the combined use of high speed infrared detectors and precision electronics. The system is compact, yet rugged, providing reliable operation in the most severe of industrial environments. The LANDSCAN LSP SYSTEM comprises: LSP Linescanning Thermometer LSP Processor...
User Guide Nomenclature The LSP Linescanning Thermometer detail label can be found on the black scanner body section. The label displays the scanner serial number, the model number and the 'CE' conformity mark. The model number indicates specific information about the unit, including 'Wavelength' and 'Temperature Range'. Example: Temperature Range Series Number...
User Guide Specifications - LSP Series Specification LSP5FL LSP50 LSP52 LSP61 Operating Wavelength: 5µm 3 to 5µm Temperature Range: 150 to 750°C/ 150 to 750°C/ 500 to 1100°C/ 50 to 400°C/ 302 to 1382°F 302 to 1382°F 932 to 2012°F 122 to 752°F...
Choose a mounting location which minimises external heating of the scanner. If the ambient temperature of the unit exceeds the specified maximum, a cooling system, available from Land Instruments, must be fitted. The full range of Land cooling and purge accessories can be found in the Installation Accessories section of this User Guide.
User Guide Alignment And Scan Direction The Land LSP Linescanning Thermometer incorporates an integral laser unit (model dependent) to aid alignment during installation. Details on the use of this feature are described in section 4.0. Where this laser alignment feature is not available, precise alignment may be accomplished through the use of a mobile 'hot source', to identify the plane and extents of the scan line.
The LSP Linescanning Thermometer requires just one electrical interface for normal operation. This interface is made to the LSP Processor, via the interface cable (Land part no. 031.402) supplied with the system. The cable is supplied pre-terminated at the scanner connection end, but the processor end is unterminated to allow the cable to be cut to suit the application.
When the LSP Linescanning Thermometer is to be used in an environment where high concentrations of dust are likely to be encountered, it is highly recommended that the Land air-purge mounting accessory should be utilised. The mounting plate incorporates a cross flow purge for the scanner window. Although this will keep the window free from dust particles, it will not however, clear the instrument sight path.
User Guide LASER ALIGNMENT Warning CLASS 2 Laser Product. DO NOT stare into laser beam. (1.0mW maximum output at 635nm) DO NOT look directly towards the scanner window, or into the laser beam during operation. If the laser is projected onto a highly reflective surface, DO NOT look at the laser stripe from a position where a direct ('mirror-like') reflection may enter the eye.
User Guide Using The Laser Alignment Tool (Model Dependent) Ensure that all CLASS 2 Laser Safety Warnings are adhered to at all times when the laser alignment tool is in use. Depress the Laser Alignment button which is positioned adjacent to the scanner interface connector on top of the scanner body.
Need help?
Do you have a question about the LSP5FL and is the answer not in the manual?
Questions and answers