NTRODUCTION 1.1 Overview The 8808F SFP Gigabit Ethernet & PoE Fiber Switch is a an all-in-one robust solution. Provides (8) 10/100/1000 Base-T RJ-45 ports with built in IEEE 802.3af/at PoE support up to 328ft / 100m allowing you to connect several IP security cameras or PoE devices. Support up to 4 1000 Base-X SFP (Small Form-Factor Pluggable) modules for connecting your fiber network for high speed data computing.
• (1) 8808F Gigabit Ethernet & PoE Fiber Switch Quickstart Guide Manual 2.2 Installation Precautions To avoid damaging the 8808F device or personal injury by improper use, please observe the following precautions. 2.2.1 Safety Precautions This is a Level A product, which may cause radio disturbance in a living environment.
2.3 Installation Methods There are 3 ways you can install the 8808F Switch: In a rack, on a workbench or in a wall-hung installation. Caution Please pull out the power plug before installing or moving the switch. Grounding and lightning protection can greatly increase the protection level of the switch.
Use a network cable to connect the switch to a PC or other LAN device via the Ethernet port, not the console port. (Note: The VLAN ID of the 8808F Ethernet port must 1) Switch must be connected to the Management PC and use that PC to configure the 8808F Switch.) Figure 2-3 Connect configuration cable...
PC (not the console port). 3.2 Set Up Network Connection 1) You need to set the IP address of the PC and the 8808F switch in the same network segment. The default IP address of the switch is 192.168.1.200, and the network gate is 255.255.255.0.
255.255.255.0). 3) Check whether the computer’s port VLAN ID is 1? - By default, the management VLAN is VLAN 1, same as each port of the 8808F switch. After inputting the correct password, click <Login>, the browser will display the 8808F web management page as seen in the screenshot below: 3.3.2 Change Language...
3.3.4 The Default Configuration The following table lists some import default configuration settings of the 8808F SFP Switch. All of the features will be described in detail in the following chapters. The default configuration is set for most cases. Please configure your settings to the appropriate application requirements and settings.
4.2.2 Port Speed Limit The 8808F Switch provides port-based entry speed limitations. Users can restrict ports traffic flow or cancel port flow restrictions. Users can also choose a fixed rate which is: downlink ports 1 ~ 1000Mbps, uplink ports 1 ~ 1000Mbps, accuracy is 1Mbps. Port restrictions include: Unicast packets, Multicast packets, and Broadcast packets.
On the [VLAN / Port VLAN] page, you can observe the VLAN settings of all the current ports on the 8808F switch and can set several functions such as [Port Range], [Link Type], [VLAN Forwarding List], [VLAN-untagged Mark List] as shown in the figure below:...
Page 23
VLAN 20. • Enter 1-10 within the port range (or click on the box in front of the ports); • Choose <Trunk> on the menu (the 8808F switch’s connection is generally used with Trunk Mode); • Enter 20 for the default VLAN ID;...
Change the VLAN name that needs configuration Configuration directions for example: Rename VLAN 20 name from “Enable-IT” to “Orange Coast Manila” • Enter 10 to VLAN ID (or click on the box in from of the VID 10); • Enter “Orange Coast Manila” to the VLAN Name;...
4.6.2 Email Alarm The 8808F switch, if running an event supervision, the supervision will send an alert message to defined mail recipients when something is wrong about defining time and if some abnormal event occurs. Supervision is also periodically sends all log messages to predefined recipients.
Port Mirroring refers to copying the monitor port data to a designated monitoring port. For data analysis and monitoring, the 8808F Switch supports multiple mirroring to one mirroring - copy packets from multiple ports to a monitor port. User can also specify the direction of monitored packets, such as: only monitor designated ports messaging.
IP address is a 32 bit length address connected to Internet equipment. IP addresses consist of 2 parts: Network-ID and Host-ID. On the [System Management / IP Address] page you can check the IP Addresses for the 8808F device shown below: Caution You can set the IP Address range as 192.168.x.x., 172.[16-31].x.x or 10.x.x.x...
2) Each port on the 8808F switch will provide a maximum output power of 30W even if the user sets it beyond 30W, it will still only output a max of 30W.
Online Technical Services The Enable-IT Support Portal is available 24/7 to open a ticket or check the status of one. Please use this support website as your first source for help as it contains an on-line knowledge base of articles, documentation, FAQ's and other problem-solving resources.
Remedies for Breach of Warranty. In the event of a breach of the foregoing warranty, Enable-IT will, in its sole discretion and at its cost, and subject to the terms of the following paragraph, repair the non-conforming Product, replace the non-conforming Product with a new or reconditioned Product or refund the purchase price for the Product.
Page 48
USING THE PRODUCT. 2. LIMITATION OF LIABILITY. IN NO EVENT SHALL ENABLE-IT BE LIABLE TO THE END USER, OR ANY THIRD PARTY, FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING OUT OF THE SALE OR USE OF THE PRODUCT (INCLUDING...
Need help?
Do you have a question about the 8808F and is the answer not in the manual?
Questions and answers