Quoizel HC8409IB Assembly Instruction Sheet

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A21 Medium Base bulb 150W Maximum.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar Assembly
A
x 1
Alternate
Mounting
B
screw
x 2
-
STEP 1 Attach the Glass Panels to the Fixture Body
A. Unscrew lock screws and remove the cage from the Fixture Body (D).
B. Remove Allen screws and tabs from the top edge of the cage. Insert
the Glass Panel (C) into the slot in the bottom edge of the cage.
Attach tabs onto the top edge of the Glass Panel (C) and line up
holes on tabs to mounting holes on the top of the cage. Secure by
threading Allen screws back into the mounting holes on the top edge
of the cage. Tighten until snug with screwdrivers.
C. Attach the fixture hood onto the top
edge of cage and secure with lock
screws previously removed. Tighten
until snug with screwdrivers.
Figure 1
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2016 QuoizelInc.
Assembly Instruction Sheet #IS-HC8409IB
for product cleaning tips. Go to the
20-30 minutes
C
Fixture Body
D
x 1
Lock
Screw
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style HC8409IB
Care + Maintenance selection.
-
STEP 2 Installing the Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Glass Panel Outlet
x 4
Mounting Screw
or Alternate Short
Mounting Screw
-
STEP 3 Test Fit the Backplate to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (D) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (D) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screw
or alternate short mounting screw on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws
in or out of the crossbar until the correct length is achieved. Once
D
Fixture
the backplate and Fixture Body (D) is secure, remove the mounting
Hood
ball and Fixture Body (D) and proceed to Step 4.
Allen
Screw
Tab
C
Cage
Slot
1of2
A
Box
Supply Wires
with Ground Wire
Mounting Ball
Mounting Screw
or Alternate Short
Mounting Screw
A
Hex Nut and
Lock Washer
Backplate
Figure 3
_R1
.
Outlet Box Screws
(not included)
Figure 2
D
ReleasedDate:2016-12-08