Quoizel CRG9010MB Manual

6 CORPORATE PARKWAY
, .
GOOSE CREEK SC 29445
. .
www quoizel com
Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A21 Medium Base bulb 150W Maximum or
(1) Medium Base Vintage bulb is recommended but not supplied.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Mounting Screw
A
x 3
Fixture
B Hood
x 1
Fixture
F
Body
x 1
-
STEP 1 Install Bulb and Fixture Hood
A. Insert Glass Panels (C) into the slot in the bottom edge of the Cage
properly. Place Clips (G) on the top edge of the Cage to hold Glass
Panels (C), secure by threading Flat Head Screws (H) onto Cage .
Tighten until sung. (See view A)
B. Insert bulb onto socket and screw snugly into place
C. Attach Fixture Hood (B) onto top edge of Cage and align holes on
the Fixture Hood (B) to mounting
holes on Tabs at the top edge of the
Cage. Attach Tabs (E) onto fixture
hood and secure with Lock Screws
(D). Tighten until snug with
screwdrivers.
H
G
C
Cage
Slot
View A
.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2016 QuoizelInc.
Assembly Instruction Sheet #IS-CRG9010MB
for product cleaning tips. Go to the
20-30 minutes
Glass Panel
C
x 4
Lock Screw
D
x 4
Flat Head
H Screw
x 4
B
D
Vintage Bulb
(recommended
but not supplied)
Socket
F
Slot
Figure 1
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style CRG9010MB
Care + Maintenance selection.
-
STEP 2 Drill Pilot Holes on Post
A. Carefully fit the Post Fitter over the end of the
Post (not supplied), making sure the Post
Fitter is fully seated.
B. Mark the drill point for the (3) Mounting
Tab
Screws, using (3) Mounting Holes as
E
x 4
reference. After marking hole locations,
remove fixture from post and drill 1/16" pilot
holes for screws.
Clip
G
x 2
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined
together. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
-
STEP 4 Attach Fixture Body to Post
A. Coat the top 1" of the Post with Clear
Silicone Caulk (not supplied) and
position the Post Fitter onto the Post. Be
E
sure to seat it completely, aligning the
holes in the Fitter with the 1/16" Pilot
Holes drilled into the Post.
B. Secure the Fixture to Post with (3)
Mounting Screws (A).
Your fixture is now assembled and
ready to use. Enjoy!
1of2
Post Fitter
Mounting Hole
Figure 2
Post
White wire
from fixture
Black wire
Figure 3
from fixture
Ground wire
from fixture
Post Fitter
Mounting Hole
Figure 4
Post
ReleasedDate:2017-09-13
A