Related Manuals for Ekinex EK-SN2-TP-GAA
Summary of Contents for Ekinex EK-SN2-TP-GAA
- Page 1 Application manual KNX standard wall presence detector with movement function EK-SN2-TP-GAA EK-SN2-TP-GAE...
-
Page 2: Table Of Contents
Troubleshooting ............................27 Package contents ............................ 27 Dimensions .............................. 28 Markings ..............................28 Maintenance ............................28 Disposal ..............................28 General warnings ............................. 29 Other information ............................. 29 Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 2... - Page 3 Application manual KNX standard wall presence detector with movement function EK-SN2-TP-… Revision Changes Date Written by Verified by First release 29/09/2022 G. Schiochet Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 3...
-
Page 4: Scope Of The Document
KNX standard wall presence detector with movement function EK-SN2-TP-… Scope of the document ® This application manual describes application details for the ekinex KNX standard wall presence detector with movement function EK-SN2-TP. The document is aimed at the system configurator as a description and reference of device features and application programming. -
Page 5: Product Description
Light measurement range: 10 ... 2000 Lux Housing, lens and frame in plastic material Safety standards: IEC 61000-6-1 / IEC 61000-6-3 / EN 55014 / EN 50491 Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 5... -
Page 6: Versions
Relative humidity: 95% not condensing Versions The sensor is supplied in 2 versions: EK-SN2-TP-GAA, in white color, and EK-SN2-TP-GAE in black color. Switching, display and detection elements The device is equipped with 2 switching elements, located under the cover: ... -
Page 7: Operation
The optimal range is achieved walking through several portions of the detection area. Figure 2 - Positioning Increased sensitivity Less sensitivity movement crosses the lens movement is towards the lens beam Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 7... - Page 8 1.2 m - 1.5 m and up to 8 m at a height of 1.8 m - 2.0 m. Figure 3 - Installation at a height of 1.2 - 1.5 m Figure 4 - Installation at a height of 1.8 - 2.0 m Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 8...
-
Page 9: Limitation Of The Detection Area
Layer A: masks the area with a circle from about 0m to 9m. Layer B: masks the area with a circle from about 0m to 3m. Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 9... - Page 10 Figure 6 - Layers scheme Cut the supplied shield in such a way to remove the sectors corresponding to the desired detection area. Figure 7 – Example 1 Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 10...
-
Page 11: Mounting And Installation
Warning! In order to supply the KNX bus lines use only KNX bus power supplies (e.g. ekinex EK-AB1-TP, EK-AG1-TP or EK-AM1-TP). The use of other power supplies can compromise the communication and damage the devices connected to the bus. - Page 12 (if applicable) the frame (b) between the box and the adapter; snap-fit the plate (f). Figure 11 - Installation for round and square flush mounting box Figure 12 - Wire stripping Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 12...
-
Page 13: Connection Of The Knx Bus Line
At the end of the download, the operation of the device automatically returns to normal mode. During the programming process, the programming LED is turned off. Now the bus device is programmed and ready for use. Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 13... -
Page 14: Operations
In the event of a power failure, the detector enters AUTO mode once the power is supplied again, even the switch is set to ON or OFF. Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 14... -
Page 15: Walk Test
Repeat the procedure in other selected radial directions, particularly if a shield is applied on the lens. Repeat the above steps until desired performance is achieved. Figure 15 - Walk Test Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 15... -
Page 16: Auto / Semi-Auto Mode (Absence Detection Function)
The ambient light level changes from bright to dark: to avoid unnecessary switching on / off of the load due to temporary variations in the ambient light value caused by events (e.g. Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 16... -
Page 17: 2-Level (Standby Lighting) Function
Options for “Behaviour at switching ON (or OFF) lock by CO are “no reaction”, “switch OFF” and “switch ON”. The number of detected movements (“windows”) within a time frame (“Duration”) can be set. Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 17... -
Page 18: List Of Ets Parameters
Enable the control channel and show the respective group of parameters. Disable Light control output C2 Device type = Master Enable Enable the control channel and show the respective group of parameters. Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 18... -
Page 19: Menu: Motion Sensors
“ETS”, all the parameters on detector can only be changed by ETS ® after completing the object build up. Note: this setting is only relevant for the two Light Control channels (C1-C2). Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 19... -
Page 20: Menus: Light Control Output C1 / C2
Although not specified below, these options are only listed if the corresponding channels are active. Figure 18 - Light control output C1 / C2 – Switching parameters Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 20... - Page 21 Lux / Time etc. selected by = ETS Sets the delay before the output is switched off (or to standby level, if enabled) in absence of detected movement. Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 21...
-
Page 22: Menus: Hvac Control Output C3 / C4
The following parameters are repeated for each of the two HVAC Control channels C3 and C4 Although not specified below, these options are only listed if the corresponding channels are active. Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 22... - Page 23 Device type = Master object Switch on Value used as output status of the detector when it is triggered (i.e., when movement / presence is detected) and switched OFF. Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 23...
-
Page 24: Menus: Alarm Function
Behaviour at switching off lock by communication Switch off Device type = Master object Switch on Value used as output when the alarm status is switched to OFF. Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 24... -
Page 25: Ets Communication Objects List
C3 HVAC Control Output 1 bit CR-T- [1.001] Switch HVAC Output C3 = enabled C4 HVAC Control Output 1 bit CR-T- [1.001] Switch Device type = Master Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 25... - Page 26 Device type = Master Lock Alarm 1 bit C-W-- [1.003] Enable Alarm function enabled Device type = Master Alarm Output 1 bit CR-T- [1.005] Alarm Alarm function enabled Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 26...
-
Page 27: Troubleshooting
There are moving objects in Make sure there are no swaying or the detection area moving objects within the detection coverage 17 Package contents EK-SN2-TP Sensor Lens shield Instruction sheet Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 27... -
Page 28: Dimensions
At the end of its useful life the product described in this datasheet is classified as waste from electronic equipment in accordance with the European Directive 2012/19/EU (WEEE recast), and cannot be disposed together with the municipal undifferentiated solid waste. Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved Pag. 28... -
Page 29: General Warnings
® ® and ETS are registered trademarks of KNX Association cvba, Brussels. © EKINEX S.p.A. The company reserves the right to make changes to this documentation without notice. Rev. 1.0 – 29/09/2022 MAEKSN2TP_EN © Ekinex S.p.A. – All rights reserved...
Need help?
Do you have a question about the EK-SN2-TP-GAA and is the answer not in the manual?
Questions and answers