Proluxe Senik Flex Quick Start Manual

These products may represent a possible shock or fire hazard if
improperly installed or attached in any way. Products should be
installed in accordance with these instructions, current electrical
codes, and/or the current National Electric Code (NEC).
Use this fixture with a 24V DC power supply only (sold
separately). Any other power supply may damage the fixture.
To reduce the risk of fire, electric shock or injury to persons, use
this flexible light only with American Lighting/Prizm recommended
drivers, controllers, power connectors, splices and extensions.
SAFETY INFORMATION
• Read all installation instructions before beginning; if not qualified, do not attempt installation. Contact a qualified electrician.
• To reduce the risk of fire, electric shock, or injury to persons, pay close attention to this manual and stay within its guidelines when using this
product. Save these instructions for future use.
• Do not cover this product as the covering may cause product to overheat, melt, or ignite.
• Risk of fire or electric shock. Uncoil flexible light prior to plugging in. Do not operate Sēnik Flex while it is tightly coiled.
• Do not route the cord or Sēnik Flex through walls, ceilings, doors, windows, or any similar part of the building structure.
• Secure this flexible light using only factory recommended mounting clips or channel (PZM-SFLEX-SW-CHAN-CLIP or PZM-SFLEX-SW-CHAN-1M
for static white type, PZM-SFLEX-RGBW-CHAN-CLIPS or PZM-SFLEX-RGBW-CHAN-1M for RGBW type), sold separately.
• Do not secure this product or its cord with staples, nails, or like means that may damage the outer jacket or cord insulation.
• Do not use if there is any damage to the PU housing or power cord insulation. Inspect periodically.
• Do not install on gates or doors, where subject to continuous flexing.
• Do not install near flammable liquids or other flammable materials.
• Follow instructions carefully when cutting Sēnik Flex. Ensure all end caps are properly sealed with appropriate silicone or PU type glue.
• This product is not intended to be cut in the field. If a shorter length of Sēnik Flex is required, please contact American Lighting directly for
information on our Custom Cut program. Any cuts, connections, or sealed ends that are made by anyone other than an American Lighting
Custom Cut representative will void the warranty.
• This product is designed for use by a qualified installer.
• This product is for decorative use only. Not to be used by children as a toy. Keep out of reach of small children.
• Do not exceed 10.05 meters or 33 feet maximum run distance in any single inter-connected run.
• Size your 24V DC driver appropriately for your run distance of Sēnik Flex using 10W per meter or 3.05W per foot as a guide. Be sure not to
load any driver to 100% as this will reduce its efficiency. A 90% maximum load is recommended for driver longevity.
• The rated ambient temperature range for Sēnik Flex is -20°C (-4°F) to 40°C (104°F).
• The maximum bend radius of PZM-SFLEX series product is 30cm or 11.8". Do not twist, drop, hang, sag, or bend product in any way other than
intended. This product can only bend vertically in relation to its light output. See Figure 1 below for reference.
FIGURE 1
When using outdoor portable lighting products, basic safety precautions should always be followed to reduce the risk of
fire, electric shock, and personal injury, including the following:
• Use outdoor rated UV-Cure type glue at all power and linking connections, including end cap, especially when using outdoors.
• Use ground fault circuit interrupter (GFCI) protection on the circuit(s) or outlet(s) when using outdoors.
• Use only UL approved outdoor extension cords, such as type SW, SOW, STW, STOW, SJW, SJOW, SJTW, or SJTOW. This designation is
marked on the jacket of the extension cord.
www.ProluxeLighting.com
WARNING
WARNING
WARNING
Sales@ProluxeLighting.com | Denver, CO | 866.700.5648
Do not operate Sēnik
Flex while it is coiled
or on the reel.
To reduce the risk of fire, electric shock or injury to persons,
make sure that the electrical power to the fixture is
disconnected at the source prior to installation or any servicing.
WARNING
Do not
Do not hang droop or sag
WARNING
©2022 Proluxe Lighting REV.2212