Advertisement
Available languages
Available languages
Installation
• The minimum distance between the supporting surface
for the cooking equipment on the hob and the lowest part
of the range hood must not be less than 50cm from
electric cookers and 65cm from gas or mixed cookers.
If the instructions for installation for the gas hob specify a
greater distance, this must be adhered to.
Electrical connection
The installation must be performed by a qualified
technician.
The mains power supply must correspond to the rating
indicated on the plate situated inside the hood. If provided
with a plug connect the hood to a socket in compliance
with current regulations and positioned in an accessible
area, after installation. If it not fitted with a plug (direct
mains connection) or if the plug is not located in an
accessible area, after installation, apply a double pole
switch in accordance with standards which assures the
complete disconnection of the mains under conditions
relating to over-current category III, in accordance with
installation instructions.
WARNING! Before re-connecting the hood circuit to
the mains supply and checking the efficient function,
always check that the mains cable is correctly assembled.
The hood is provided with a special power cable ; if the
cable is damaged, request a new one from Technical
Service.
Mounting
Before beginning installation:
•
Check that the product purchased is of a suitable size for the chosen installation
area.
•
Remove the charcoal (*) filter/s if supplied (see also relative paragraph). This/these
is/are to be mounted only if you want lo use the hood in the filtering version.
•
Check (for transport reasons) that there is no other supplied material inside the
hood (e.g. packets with screws (*), guarantees (*), etc.), eventually removing them
and keeping them.
Expansion wall plugs are provided to secure the hood to most types of walls/ceilings.
However, a qualified technician must verify suitability of the materials in accordance
with the type of wall/ceiling. The wall/ceiling must be strong enough to take the weight
of the hood.
Do not tile, grout or silicone this appliance to the wall. Surface mounting only.
Note: The parts marked with the symbol "(*)" are optional accessories supplied only
with some models or otherwise not supplied, but available for purchase.
Maintenance
Cleaning
Clean using ONLY a cloth dampened with neutral liquid detergent. DO NOT CLEAN
WITH TOOLS OR INSTRUMENTS. Do not use abrasive products. DO NOT USE
ALCOHOL!
Always wear work gloves for all maintenance operations.
Grease filter
Fig. 10-29
Traps cooking grease particles.
The grease filter must be cleaned once a month using non aggressive detergents,
either by hand or in the dishwasher, which must be set to a low temperature and a short
cycle. When washed in a dishwasher, the grease filter may discolor slightly, but this
does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Charcoal filter (Optional)
Fig. 28
It absorbs unpleasant odors caused by cooking.
The saturation of the charcoal filter occurs after more or less prolonged use, depending
on the type of cooking and the regularity of cleaning of the grease filter.
In any case it is necessary to replace the cartridge at least every four mounths (or when
18
the filter saturation indication system – if envisaged on the model in possession –
indicates this necessity).The charcoal filter may NOT be washed or regenerated.
Assembly
Hook the charcoal filter at the back on the metal tongue of the hood first, then on the
front with the two knobs.
Disassembly
Remove the charcoal filter by turning the knobs fixing it to the hood by 90°.
Buying charcoal filters
The Charcoal filter can be bought at Samsung Service Center. Please refer to the last
page of manual.
Replacing lamps
Replacing lamps and/or control gear
The hood is equipped with a lighting system based on LED technology.
The LEDs guarantee an optimum lighting, a duration up to 10 times longer than the
traditional lamps and allow to save 90% electrical energy.
The lighting system cannot be replaced by the user, contact Customer Service in case
of malfunction.
Operation
To select hood functions, simply touch the controls:
T1. Button ON/OFF suction motor
T2. Button to select low suction speed (power)
Saturation indicator for grease filter
When flashing, perform maintenance of the grease filter; then keep the button T1
pressed for a long time to stop the flashing (hood is ON).
T3. Button to select medium suction speed (power)
Saturation indicator charcoal filter
When flashing, perform maintenance of the charcoal filter, if installed, then keep
the button T1 pressed for a long time to stop the flashing (hood is ON).
T4. Button to select high and Boost suction speed (power)
Press once to select high suction speed (power) (LED on);
Press again to select Boost suction speed (power) (LED flashing).
Note: The Boost suction (power) speed lasts for approximately 5 minutes, then the
high suction speed (power) is set
automatically.
T5. Automatic shutdown button (Timer) :
Press this button to set the automatic shutdown of the active suction speed
(power):
Low suction speed (power): 20 minutes
Medium suction speed (power): 15 minutes
High suction speed (power): 10 minutes
T6. Button ON/OFF lighting
Activation of the charcoal filter saturation indicator
This indicator is normally deactivated. To activate it, proceed as follows:
With the hood off, press and keep pressed simultaneously T2 and T3: T2+T3
switch ON , the hood gives out a "BEEP", the charcoal filter saturation is activated
Deactivation of charcoal filter saturation LED: repeat the operation described
above;T2+T3 flash, (then only T2) ,the hood gives out a "BEEP", the charcoal filter
saturation is deactiveted.
Advertisement
