Table of Content Preface Table of Content ... 1-2 Regulations Information... 1-5 FCC-B Radio Frequency Interference Statement ... 1-5 FCC Conditions ... 1-6 CE Conformity ... 1-6 Safety Instructions... 1-7 Safety Guideline for Using Lithium Battery ...1-11 WEEE Statement ... 1-15 Optical Drive Device Notice ...
Page 3
Right Side View ... 2-17 Left Side View... 2-19 Rear Side View... 2-21 Bottom Side View ... 2-22 Getting Started Power Management ... 3-2 Connecting the AC Power ... 3-2 Using the Battery Power... 3-4 ECO Engine -- Power Saving Function ... 3-9 GPU Boost Function...3-11 Power Management in Windows OS ...
Page 4
Components Replacement and Upgrade ... 3-43 BIOS Setup About BIOS Setup... 4-2 When to Use BIOS Setup... 4-2 How to Run BIOS Setup... 4-2 Control Keys ... 4-3 BIOS Setup Menu... 4-4 Main Menu... 4-5 Advanced Menu... 4-7 Security Menu... 4-9 Boot Menu ...4-11 Exit Menu...
Regulations Information FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Shield interface cables and AC power cord, if any, must be used in order to comply with the emission limits. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference.
Safety Instructions Read the safety instructions carefully and thoroughly. All cautions and warnings on the equipment or user’s manual should be noted. Keep the User’s Guide that comes with the package for future reference. Keep this equipment away from humidity and high temperature. Lay this equipment on a stable surface before setting it up.
Page 8
Do not leave the equipment in an unconditioned environment with a storage temperature above 60°C (140°F) or below 0°C (32°F), which may damage the equipment. The unit should be operated under maximum ambient temperature of 40°C (120°F). Make sure the power voltage is within safety range and has been adjusted properly to the value of 100~240V before connecting the equipment to the power outlet.
Page 9
Always keep the strong magnetic or electrical objects away from the equipment. When installing the coaxial cable to the TV Tuner, it is necessary to ensure that the metal shield is reliable connected to protective earthing system of the building. Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable.
1-10 Green Product Features Reduced energy consumption during use and stand-by Limited use of substances harmful to the environment and health Easily dismantled and recycled Reduced use of natural resources by encouraging recycling Extended product lifetime through easy upgrades Reduced solid waste production through take-back policy Environmental Policy The product has been designed to enable proper reuse of parts and recycling and should not be thrown away...
1-11 Safety Guideline for Using Lithium Battery (English) CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions. (French) (Français) ATTENTION: II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du meme type ou d’un type équivalent recommandé...
Page 12
1-12 (Turkish) (Türkçe) UYARI: Pil yanlıs yerleştirilirse patlayabilir. Aynı ya da muadili bir pille degistiriniz. Kullanılmış pilleri üreticinin talimatlarına göre degerlendiriniz. (Greek) (Ελληνικά) ΠΡΟΣΟΧΗ: Κίνδυνος έκρηξης εάν η μπαταρία τοποθετηθεί λανθασμένα. Να αντικαθιστάτε μόνο με τον ίδιο ή αντίστοιχο τύπο με αυτό που συνιστά ο κατασκευαστής του εξοπλισμού. Να απορρίπτετε τις χρησιμοποιημένες μπαταρίες...
Page 13
1-13 (Korean) (한국어) 주의: 배터리를 올바로 교체하지 않으면 폭발할 위험이 있습니다. 타입이 장치 제조업체에서 권장하는 것과 동일하거나 동등한 폐기하십시오. (Vietnamese) (Tieng Viet) LƯU Ý: Thay thế pin không tương thích có thể dẫn đến nguy cơ bị nổ. Chỉ thay thế bằng pin cùng loại hoặc loại tương ứng khuyên dùng bởi nhà...
Page 14
1-14 (Portuguese) (Português) ADVERTÊNCIA: Perigo de explosão se a bateria é substituída incorrectamente. Substitua somente com o mesmo tipo ou equivalente recomendado por o fabricante do seu equipamento. Descarte as baterias utilizadas de acordo com as instruções do fabricante. (Swedish) (Svenska) VARNING: Explosionsfara vid felaktigt batteribyte.
1-15 (Croatian) (Hrvatski) OPREZ: Opasnost od eksplozije ako se baterija zamijeni neprikladnom. jednakom ili nadomjesnom vrstom prema preporuci proizvođača. proizvođača. (Estonian) (Eesti) ETTEVAATUST! Plahvatusoht, kui aku on valesti paigaldatud. Asendage ainult sama või tootja poolt soovitatud võrdväärse akuga. Hävitage kasutatud aku vastavalt tootja juhistele. در...
Page 16
1-16 (French) (Français) Au sujet de la directive européenne (EU) relative aux déchets des équipement électriques et électroniques, directive 2002/96/EC, prenant effet le 13 août 2005, que les produits électriques et électroniques ne peuvent être déposés dans les décharges ou tout simplement mis à la poubelle. Les fabricants de ces équipements seront obligés de récupérer certains produits en fin de vie.
Page 17
1-17 (Turkish) (Türkçe) Avrupa Birliği (AB) Kararnamesi Elektrik ve Elektronik Malzeme Atığı, 2002/96/EC Kararnamesi altında 13 Ağustos 2005 tarihinden itibaren geçerli olmak üzere, elektrikli ve elektronik malzemeler diğer atıklar gibi çöpe atılamayacak ve bu elektonik cihazların üreticileri, cihazların kullanım süreleri bittikten sonra ürünleri geri toplamakla yükümlü...
Page 19
1-19 (Indonesian) (Bahasa Indonesia) Sesuai dengan Regulasi Uni Eropa ("UE") perihal WEEE (Limbah Peralatan Listrik dan Elektronik), Directive 2002/96/EC, yang berlaku sejak 13, 2005, produk "peralatan listrik dan elektronik" tidak lagi dapat dibuang sebagai sampah umum dan pabrik peralatan elektronik diwajibkan untuk mengambil kembali produk tersebut pada saat masa pakainya habis.
Page 20
1-20 (Swedish) (Svenska) Under Europeiska unionens ("EU") Weee-direktiv (Waste Electrical and Electronic Equipment), Direktiv 2002/96/EC, vilket trädde i kraft 13 augusti, 2005, kan inte produkter från "elektriska och elektroniska utrustningar" kastas i den vanliga hushållssoporna längre och tillverkare av inbyggd elektronisk utrustning kommer att tvingas att ta tillbaka sådan produkter när de är förbrukade.
Page 21
1-21 (Norwegian) (Norsk) Under den europeiske unionens ("EU") direktiv om deponering av elektronisk og elektrisk utstyr, direktiv 2002/96/EC, som trer i effekt 13. august 2005, kan ikke produkter av "elektronisk og elektrisk ustyr" lenger deponeres som husholdningsavfall og fabrikantene av disse produktene er forpliktet å ta tilbake slike produkter ved slutten av produktets levetid.
1-22 Optical Drive Device Notice CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.”...
Congratulations on becoming an user of this notebook, the finely designed notebook. This brand-new exquisite notebook will give you a delightful and professional experience in using notebook. We are proud to tell our users that this notebook is thoroughly tested and certified by our reputation for unsurpassed dependability and customer satisfaction Manual Map This User’s Manual provides instructions and illustrations on how to operate this notebook.
Chapter 4, BIOS Setup, provides information on BIOS Setup program and allows you to configure the system for optimum use. Unpacking First, unpack the shipping carton and check all items carefully. If any item contained is damaged or missing, please contact your local dealer immediately. Also, keep the box and packing materials in case you need to ship the unit in the future.
Specification Physical Characteristic Dimension Weight Processor Type L2 Cache HyperTransport Link Special Notification Core Chips North Bridge South Bridge Special Notification 383 x 249.5 x 32.3 ~37 mm 2.4 kg (with 6-cell battery) ® Champlain 512KB to 2MB 3.2GT/s or 3.6GT/s (optional) The actual processor preinstalled in the notebook depends on the model you purchased.
Page 27
Memory Technology Memory Maximum Power AC/DC Adapter Battery Type RTC Battery Special Notification Storage (Items listed here may vary depending on the model users purchased) HDD form factor Optical Drive Device Special Notification DDR3 1066 / 1333 MHz (optional) DDR3 SO-DIMM X 2 slot 90W, 19V Input: 100~240V, 50~60Hz Output: 19V...
I/O Port Monitor (VGA) E-SATA / USB combo Mic-in/ Line-in Headphone-out/ S/PDIF-out RJ45 HDMI Card Reader Communication Port (Items listed here may vary without notice) Wireless LAN Bluetooth Audio Internal Speaker Sound Volume 15 pin D-Sub x 1 x 2 (USB version 2.0) x 1 (XD/ SD/ SDHC/ SDXC/ MMC/ MS/ MS Pro) The supported memory cards may vary without notice.
Video Graphics LCD Resolution CRT Output HDMI Output Display LCD Type Brightness WebCam HD CMOS camera Software & BIOS USB Flash Boot BIOS Others Kensington Lock Hole Compliance Discrete/ UMA (optional) 1366 x 768 Supported Supported 15.6” 16:9 HD Brightness controlled by K/B hot-keys Supported Yes, USB floppy boot up DOS only Fast Boot Support --- Yes...
Product Overview This section provides the description of basic aspects of the notebook. It will help you to know more about the appearance of this notebook before using it. Please be aware that the notebook shown in this section may vary from the actual one that users purchased. Top-open View The figure of top-open view and description shown below will lead you to browse the main operating area of your notebook.
1. Internal Microphone The built-in speaker and array microphone increase the accuracy of speech recognition feature, allow inputs to be combined into a single, higher-quality source. 2. Webcam/ Webcam LED This built-in Webcam can be used for picture taking, video recoding or conference, and any other interactive applications.
Page 32
2-10 Wireless LAN (optional) GPU Boost Power Button Power/ Power Saving function LED Press this button to launch the Wireless LAN function. Press this button to launch the GPU Boost application. Glowing amber indicates in High-performance GPU, while off in Power-saving GPU mode.
2-11 4. Touchpad Switch This switch can be used to enable or disable the touchpad. There is an optional LED on the button, glows when the touchpad is disabled. 5. Touchpad This is a pointing device of the notebook. 6. Keyboard The built-in keyboard provides all the functions of a full-sized keyboard.
Page 34
2-12 ECO Engine (Power Saving) Webcam WLAN (WiFi) (optional) Bluetooth (optional) Press and hold the Fn button, and then press the F5 button repeatedly to switch among various power saving modes provided by ECO Engine, or to turn this function off recurrently. Refer to the Power Management section in chapter 3 of this manual for the detailed information of this ECO Engine, Power Saving Function.
Page 35
2-13 (optional) Press and hold the Fn button, and then press the F10 button to turn the 3G function on. Press again to turn it off. This 3G function is optional supported depending on the model users purchased. This function button will not be available when the 3G function is not supported.
2-14 Front View Status LED Hard Disk/ Optical Drive Device In-use: Blinking blue when the system is accessing the hard disk drive or the optical drive device. Bluetooth Bluetooth Bluetooth LED indicator glows blue when Bluetooth function is enabled. Warning: For flight safety consideration, make sure this LED indicator goes out when you are in flight.
Page 37
2-15 Wireless LAN (WiFi) (optional) WLAN(WiFi) Battery: Caps Lock: Glowing blue when the Caps Lock function is activated. Num Lock: Glowing blue when the Num Lock function is activated. Wireless LAN LED indicator glows blue when Wireless LAN (WiFi) function is enabled. LED indicator goes out when this function is disabled.
2-16 Sleep State: 2. Card Reader The built-in card reader may support various types of memory card, such as MMC (Multi-Media Card), XD (eXtreme Digital), SD (Secure Digital), SDHC (SD High Capacity), SDXC (eXtended Capacity), MS (Memory Stick) or MS Pro (Memory Stick Pro) cards. Contact the local dealer for further and correct information and be noted that the supported memory cards may vary without notice.
2-17 Right Side View 1. Optical Drive Device This notebook is equipped with an optical drive device. The actual device preinstalled in the notebook depends on the model you purchased. 2. E-SATA (External Serial ATA) / USB Combo Port The E-SATA Connector allows you to connect an external Serial ATA device. Users can now utilize shielded cable outside the notebook to take advantage of the benefits the SATA interface brings to storage.
Page 40
2-18 4. RJ-45 Connector The Ethernet connector is used to connect a LAN cable for network connection.
2-19 Left Side View 1. Kensington Lock Hole This notebook provides a Kensington Lock hole, which allows users to secure the notebook in place with a key or some mechanical PIN device and attached through a rubberised metal cable. The end of the cable has a small loop which allows the whole cable to be looped around a permanent object, such as a heavy table or other similar equipment, thus securing the notebook in place.
2-20 4. HDMI Connector HDMI (High Definition Multimedia Interface) is a new interface standard for PCs, displays and consumer electronics devices that supports standard, enhanced and high-definition video, plus multi-channel digital audio on a single cable. 5. USB Port The USB 2.0 port allows you to connect USB-interface peripheral devices, such as the mouse, keyboard, modem, portable hard disk module, printer and more.
2-22 Bottom Side View 1. Battery Lock/ Unlock Button Battery cannot be moved when the button is positioned on lock status. Once the button is slid to unlock position, the battery is removable. 2. Battery Pack This notebook will be powered by the battery pack when the AC adapter is disconnected. Battery Lock/ Unlock Button Battery Pack Battery Release Button...
Page 45
2-23 3. Battery Release Button It is a bounce-back device as a preparation for releasing the battery pack. Slide it with one hand and pull the battery pack carefully with the other. 4. Ventilator The ventilator is designed to cool the system. DO NOT block the ventilator for air circulation. 5.
Power Management Connecting the AC power It is strongly recommended to connect the AC/DC adapter to the notebook and use the AC power while using this notebook for the first time. When the AC power is connected, recharging the battery will start immediately. Note that the AC/DC adapter included in the package is approved for your notebook;...
Connecting the AC Power 1. Unpack the package to find the AC/DC adapter and power cord. 2. Attach the power cord to the connector of the AC/DC adapter. 3. Plug the DC end of the adapter to the notebook, and the male end of the power cord to the electrical outlet.
Using the Battery Power This notebook is equipped with a high-capacity Li-ion battery pack. The rechargeable Li-ion battery pack is an internal power source of the notebook. Be aware of that this battery pack may be damaged if users try to disassemble the battery pack on their own.
Installing the Battery Pack To insert the battery pack, following the steps below: 1. Locate the steady gutter of the battery pack, and the battery bolt on the battery tray as shown right. 2. Align the steady gutter and battery bolt with correct orientation and make sure they are joined properly.
Releasing the Battery Pack To release the battery pack, following the steps below: Make sure the notebook is turned off, and the AC power is disconnected. Press the lock/unlock button to the unlocked position. Locate the battery release button on the bottom side.
Battery Safety Tips Replacing or handling the battery incorrectly may present a risk of fire or explosion, which could cause serious injury. Only replace the main battery pack with the same or equivalent type of battery. Do not disassemble, short-circuit or incinerate batteries or store them to temperatures above +60°...
Charging the Battery Pack The battery pack can be recharged while it is installed in the notebook. Please pay attention to the following tips before recharging the battery: If a charged battery pack is not available, save your work and close all running programs and shut down the system or Save-to-Disk.
ECO Engine -- Power Saving Function Enabling the ECO Engine ECO Engine, the outstanding and unique power saving function, provides various power saving modes – Gaming mode, Movie mode, Presentation mode, Office mode, and Turbo Battery mode, to extend the battery running time while performing different tasks with this notebook. Read the instructions bellow to activate the ECO Engine power saving function: 1.
Page 55
3-10 Presentation Mode Select this mode while performing presentation applications. Office Mode Select this mode while dealing with office documentation tasks. Turbo Battery Mode Select this mode to maximize the battery running time. ECO Off Selected to disable ECO Engine.
3-11 GPU Boost Function GPU Boost Function allows users to choose between using the discrete and the internal graphic card depending on the tasks users are currently performing. With this function, users can easily and quickly select either to maximizing the graphic performance or extending the battery running time.
Page 57
3-12 The figures show here are for reference only.
3-13 Power Management in Windows OS Power management of personal computers (PCs) and monitors has the potential to save significant amounts of electricity as well as deliver environmental benefits. To be energy efficient, turn off your display or set your PC to Sleep/ Hibernate mode after a period of user inactivity. Follow the instructions below to adjust the power management settings in Windows OS: 1.
3-15 Energy Saving Tips Activate the ECO power saving function to manage the computer’s energy consumption. Turn off the monitor after a period of user inactivity. Utilize the Fn and F12 sleep mode keys to turn into power saving mode. Tune the settings in Power Options under Windows OS to optimize the computer’s power management.
3-16 Basic Operations If you are a beginner to the notebook, please read the following instructions to assure your own safety, and make yourself comfortable during the operations. Safety and Comfort Tips The notebook is a portable platform that allows you to work anywhere. However, choosing a good workspace is important if you have to work with your notebook for a long period of time.
3-17 1. Keep your hands and feet with optimal comfort. 2. Adjust the angle and position of LCD panel. 3. Adjust the desk’s height. 4. Sit straight and keep a good posture. 5. Adjust the chair’s height. Having a Good Work Habit Have a good work habit is important if you have to work with your notebook for long periods of time;...
3-18 Knowing the Keyboard This notebook provides a full-functioned keyboard. categories: Typewriter keys, Cursor keys, Numeric keys and Function keys. The keyboard shown here may vary from the actual one, depending on which county users purchase the notebook. This keyboard can be divided into four Typewriter keys Numeric keys Cursor keys /...
3-19 Typewriter Keys In addition to providing the major function of the keyboard, these typewrite keys also provide several keys for special purposes, such as [Ctrl,] [Alt,] and [Esc] key. When the lock keys are pressed, the corresponding LEDs will light up to indicate their status: Num Lock: Press the Num Lock key to toggle the Num Lock on and off.
3-20 Cursor Keys The four cursor (arrow) keys and [Home], [PgUp], [PgDn], [End] keys are used to control the cursor movement. Move the cursor left for one space. Move the cursor right for one space. Move the cursor up for one line. Move the cursor down for one line.
3-21 The Backspace key, [Ins] and [Del] keys at upper right corner are used for editing purpose. This key is used to switch the typing mode between “insert” and “overtype” modes. Press this key to delete one character to the right of the cursor and move the following text left for one space.
Page 67
3-22 Enable or disable the touchpad function. Decrease the LCD brightness. Increase the LCD brightness. Decrease the built-in speaker’s volume. Increase the built-in speaker’s volume. Disable the computer’s audio function. Force the computer into sleep state (depending on the system configuration).
Page 68
3-23 Quick Launch [Fn] Buttons Use the [Fn] buttons on the keyboard to activate the specific applications or tools. With the help of these quick launch buttons, users will be able to do work more efficiently. Smart Pad GPU Boost ECO Engine (Power Saving) Press and hold the Fn button, and then press the F3 button...
Page 69
3-24 Webcam WLAN (WiFi) (optional) Bluetooth (optional) (optional) Press and hold the Fn button, and then press the F6 button to turn the Webcam function on. Press again to turn it off. Press and hold the Fn button, and then press the F8 button to turn the Wireless LAN (WiFi) function on.
3-25 Knowing the Smart Pad The Smart Pad integrated in your notebook allows users to perform various actions with multi-finger taps and gestures while operating the notebook, and is capable to detect the changes of the multi-finger movement performed by users precisely. This significant Smart Pad will surely bring users not only an efficient but also an enjoyable experience of using the notebook.
Page 71
3-26 Enabling the Smart Pad Smart Pad Brief Usages to the Smart Pad For the further information on how to use the Smart Pad function specifically, please refer to the instructions of Smart Pad by double clicking the Smart Pad icon ( the screen.
Page 72
3-27 Gestures Actions Taping the touchpad once with Single clicking the Left button one finger. of the mouse. Double taping the touchpad Double clicking the Left button with one finger. of the mouse. Touch the touchpad with single finger and move around your Cursor moving.
Page 73
3-28 Gestures Actions Touch the touchpad with two fingers and remain the fingers on the touchpad. Scrolling a page vertically. Move the two fingers on the touchpad vertically. Touch the touchpad with two fingers and remain both fingers on the touchpad. Scrolling a page horizontally.
Page 74
3-29 Gestures Actions Touch the touchpad with three fingers and remain it on the touchpad. Double tapping the touchpad with one finger to enable the Enabling or Disabling the Magnifying Glass function. Magnifying Glass function. To control the magnifying Using the Magnifying Glass glass, touch the touchpad with function.
Page 75
3-30 Gestures Actions Touch the touchpad with three fingers and remain the fingers on the touchpad. Browse the directory of “Computer” Move the three fingers to the upper side of the touchpad to browse “Computer.” Touch the touchpad with three fingers and remain the fingers on the touchpad.
Page 76
3-31 Gestures Actions Touch the touchpad with two fingers and remain both fingers on the touchpad. Move a finger clockwise while another remains still to rotate a selected object clockwise. Rotating a selected object Refer to the first gesture. clockwise or counterclockwise. Move a finger counterclockwise while another remains still to rotate a selected object...
3-32 About Hard Disk Drive Your notebook is equipped with a 2.5-inch hard disk drive. The hard disk drive is a storage device with much higher speed and larger capacity than other storage devices, such as the floppy disk drive and optical storage device.
3-33 Using the Optical Drive Device Your notebook is equipped with an optical drive device. The actual device preinstalled in your notebook depends on the model you purchased. Super Multi: Works as a multi-functional DVD Dual Drive and a DVD RAM Drive. Blu-ray: It is a high-capacity optical disc that holds 4.5 hours of high-definition video (HD) on a single-sided, single-layer 25GB disk.
3-34 Inserting the Disk The following instructions describe the general procedure when operating the optical storage device: 1. Confirm that the notebook is turned on. 2. Press the eject button on the panel and 3. Gently pull the tray out until fully 4.
Page 80
3-35 Removing the Disk Follow the instructions below to remove the disk that is placed in the optical storage device: 6. Press the eject button on the drive’s panel and the disk tray will slide out partially. 7. Gently pull the tray out until fully extended.
3-36 Connecting the External Devices The I/O (input/output) ports on the notebook allow you to connect peripheral devices. All devices listed here are for reference only. Connecting the Peripheral Devices Connecting the USB devices This notebook provides USB ports for connecting various USB devices, such as mouse, keyboard, digital camera, webcam, printer, and external optical storage device, etc.
Page 82
3-37 Connecting the External Display Devices This notebook provides a VGA port for connecting a larger display with higher resolution. The 15-pin-D-sub VGA port allows users to connect an external monitor or other standard VGA-compatible device (such as a projector) for a great view of the notebook display.
Page 83
3-38 This notebook provides a HDMI port for connecting a larger display with higher resolution. HDMI (High Definition Multimedia Interface) is a new interface standard for PCs, displays and consumer electronics devices that supports standard, enhanced and high-definition video, plus multi-channel digital audio on a single cable.
Page 84
3-39 Connecting the External SATA Hard Disk device The E-SATA Connector allows you to connect an external Serial ATA hard disk device. Users can now utilize shielded cable outside the notebook to take advantage of the benefits the SATA interface brings to storage. The E-SATA standard interface supports “plug-and-play”...
3-40 Connecting the Communication Devices Using the LAN The RJ-45 connector of the notebook allows you to connect the LAN (local area network) devices, such as a hub, switch and gateway, to build a network connection. For more instructions or detailed steps on connecting to the LAN, please ask your MIS staff or network manager for help.
Page 86
3-41 Using Wireless LAN Connection (optionally supported) This notebook is equipped with wireless LAN module which allows users to perform fast data transmission with the standard IEEE 802.11 for wireless LAN. This gives users the mobility to move around within a broad coverage area and still be connected to the network. By using the 64-bit/128-bit Wired Equivalent Privacy (WEP) encryption technology and Wi-Fi Protected Access feature, the optional built-in wirelesses LAN is capable to achieve a more efficient and a more secure solution to the wireless communication.
Page 87
3-42 Using Bluetooth Connection (optionally supported) This notebook is equipped with Bluetooth module which allows users to connect various Bluetooth-enabled devices to the notebook. Bluetooth provides a way to connect and exchange information between devices such as mobile phones, personal computers, printers, GPS receivers, PDAs, digital cameras, and video game consoles through a secure, globally unlicensed Industrial, Scientific and Medical (ISM) 2.4 GHz short-range radio frequency bandwidth.
3-43 Components Replacement and Upgrade Please be noticed that the memory, hard disk drive, wireless LAN / Bluetooth module and battery pack preinstalled in the product users purchased may be upgradable or replaceable by user’s request depending on the models users purchased.
Page 89
3-44 This notebook is equipped with a high-capacity Li-ion battery pack, and the battery pack is replaceable by users. To replace the battery pack, please refer to the section of Using the Battery Power for details. This notebook is equipped with a wireless LAN/ Bluetooth module, and the module may be upgradable and replaceable by authorized dealer or service center.
Page 90
3-45 To learn more about upgrade limitation, please refer to the specification in the User’s Manual provided. For any further information about the product users purchased, please contact the local dealer. Do not attempt to upgrade or replace any component of the product, if you are not an authorized dealer or service center, since it may cause the warranty void.
About BIOS Setup When to Use BIOS Setup? You may need to run the BIOS Setup when: An error message appears on the screen during the system booting up and is requested to run SETUP. You want to change the default settings for customized features. You want to reload the default BIOS settings.
Control Keys You can use only the keyboard to control the cursor in the BIOS Setup Utility. Press left arrow to select one menu title. Press up arrow to select one item under the menu title. 1) Open the selected item to change setting options. 2) Bring up a sub-menu when available.
BIOS Setup Menu Once you enter the BIOS Setup Utility, the Main Menu will appear on the screen. Select the tags to enter the other menus. The BIOS items and figures shown here are for reference only. Main Menu Show system overview information about BIOS version, CPU features, memory size and setting of system time and date.
Main Menu System Date This item allows you to set the system date. [day:month:date:year]. Month Date Year System Time This item allows you to set the system time. The system clock will go on no matter you shut down the PC or get into sleep mode. The time format is [hour:minute:second].
Page 96
System Information This item provides the information about the firmware, processor, and system memory.
Advanced Menu PowerNow This item allows you to enable or disable PowerNow function. When set to Enabled, the system always operates in a conserve power mode. If you want to optimize the processor, set this item to Disabled, so that the processor’s speed will vary depending on the use of your operating system and applications.
Page 98
AHCI Mode (Advanced Host Controller Interface) Use this item to enable or disable the AHCI Mode. Setting options: Disabled and Enabled.
Security Menu Change Supervisor Password When this item is selected, a message box shall appear on the screen as below: Enter New Password Type a maximum of eight-digit password and press [Enter]. The password typed now will replace any previously set password from CMOS memory.
Page 100
4-10 The Password Check item is used to specify the type of BIOS password protection that is implemented. Settings are described below: Setup Always To clear a set Supervisor Password/ User Password, just press [Enter] under Change Supervisor Password/ Change User Password field when prompted to enter the password.
4-11 Boot Menu Boot Settings Configuration Configure settings during system boot. Boot Device Priority These items showing the sequence of boot devices where BIOS attempts to load the disk operating system.
4-12 Exit Menu Exit & Save Changes Save the changes you have made and exit the utility. Exit & Discard Changes Exit the utility without saving the changes you have made. Discard Changes Abandon your changes and reload the previous configuration before running the utility.
Need help?
Do you have a question about the FX610 and is the answer not in the manual?
Questions and answers