Download
Share
Print this page
AQUEA 475-201 Installation & Care Manual
  1. Manuals
  2. Brands
  3. AQUEA Manuals
  4. Swimming Pool Filter
  5. 475-201
  6. Installation & care manual

AQUEA 475-201 Installation & Care Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
I N S T A L L A T I O N
NOTE:
1.
READ THIS DOCUMENT PRIOR TO INSTALLATION. IMPROPER INSTALLATION WILL VOID WARRANTY.
2.
PRODUCT ONLY TO BE INSTALLED & SERVICED BY A SUITABLY QUALIFIED PROFESSIONAL.
3.
DO NOT USE ACID/CHEMICAL WASHES . DISCOLORATION MAY OCCUR AND WILL VOID WARRANTY.
4.
INSTALLER TO ENSURE INSTALLATION MEETS ALL APPLICABLE ENGINEERING & REGULATORY
REQUIREMENTS.
5.
DO NOT CARRY LID WITH KEY.
6.
ALWAYS REMOVE KEY FROM LID ONCE LOCKED. KEEP KEY OUT OF REACH OF CHILDREN.
7.
THIS MANUAL CONTAINS IMPORTANT INFORMATION. ONCE INSTALLATION IS COMPLETE
INSTALLER MUST PROVIDE THIS MANUAL TO OWNER/OPERATOR TO STORE IN A SAFE PLACE.
C A R E
&
PART NO. 475 -201
G U I D E
|
|
475 -203
475 -205
|
475 -207

Advertisement

loading
Need help?

Need help?

Do you have a question about the 475-201 and is the answer not in the manual?

Questions and answers

Related Manuals for AQUEA 475-201

Summary of Contents for AQUEA 475-201

  • Page 1 I N S T A L L A T I O N C A R E G U I D E & PART NO. 475 -201 475 -203 475 -205 475 -207 NOTE: READ THIS DOCUMENT PRIOR TO INSTALLATION. IMPROPER INSTALLATION WILL VOID WARRANTY. PRODUCT ONLY TO BE INSTALLED &...
  • Page 2 Registered Design. Specifications subject to change without notice. ® AQUEA is a registered trademark of Vantage Products Pty. Ltd. ® The contents of this manual are the exclusive copyright of AQUEA and may not be reproduced without written © permission. 2022 ®...

  • Page 3: Kit Contents

    322.0 Overall Inlay Length 322.0 All dimensions in millimeters. Tolerance +/- 1.0mm FEEDBACK & SUGGESTIONS We are continually looking for ways to improve and expand our product range. Please contact us at hello@aquea.com.au if you have any feedback or suggestions!
  • Page 4 OUTER FRAME PREPARATION - STONE/TILE NEW BUILD NEW BUILD • Check & confirm finished height of stone/tile. • Check & confirm overall height of V-LOCK model to be installed (See Page 2). • Prepare a level bed slightly larger than overall size of Outer Frame including mortar bed allowance (A).
  • Page 5 OUTER FRAME INSTALLATION - STONE/TILE To lay mortar bed: • Using appropriate mortar mix, insert mortar into recess surrounding skimmer box opening (A). IMMEDIATELY REMOVE ANY MORTAR THAT FALLS INTO SKIMMER BOX To position Outer Frame: • Place Outer Frame on mortar bed. Mortar must fully support Outer Frame (A).
  • Page 6 OUTER FRAME INSTALLATION - Decking To prepare sub-frame: • Construct square opening in sub-frame slightly larger than Outer Frame, centred over skimmer box opening (A). • Fix corner gussets to sub-frame opening. Ensure gussets are recessed so top surface of Outer Frame rim is flush with finished decking level (B).
  • Page 7 LID INLAY INSTALLATION - STONE/TILE To cut inlay material to size: • Place inlay material in desired layout on a flat surface. • Carefully cut to correct size to suit V-LOCK Lid (A). (See Page 2) To mark V-notch cut-out: •...
  • Page 8 FOR INLAYS MORE THAN 3 mm THINNER THAN INTERNAL LID DEPTH To apply adhesive : • Insert V-LOCK Adhesive into caulking gun & cut nozzle to provide a minimum 6mm wide bead. • Apply a generous, even bead across entire internal surface of Lid (A). •...
  • Page 9 LID INLAY INSTALLATION - Decking To prepare Lid for mounting battens: • Invert Lid and select preferred mounting points for correct batten orientation. • Drill holes in pre-moulded locations to suit preferred fasteners and batten direction (A). To attach battens: •...

  • Page 10: General Usage

    GENERAL USAGE TO OPEN LID LOCK To unlock Lid: • Insert Lid Key into lock as shown (A). • Rotate Key 90 degrees clockwise to UNLOCK unlock position. Lid Key is now captive in Lid. To remove Lid: • Using Lid Key as a handle lift Lid upwards (A), then grab edges of Lid by hands and remove from Outer Frame.

  • Page 11: Warranty Policy

    Refurbished parts may be used to repair the Products. (j) the Product has been subject to abnormal corrosive conditions All repairs are to be carried out by AQUEA or its authorised repairer or abrasive chemicals; only. This warranty do es not cover any costs related to travel, (k) the defect is the result of corrosion or normal wear and tear;...
  • Page 12 A Q U E A ® (a division of Vantage Products Pty. Ltd.) U 1 1 / 2 2 - 2 4 R E D L A N D D R I V E , M I T C H A M , V I C T O R I A 3 1 3 2 . S A L E S &...

This manual is also suitable for:

475-203475-205475-207