Iget SECURITY M3P4 Installation Manual

Trigger Mode Clarification/ Funkce Trigger/ Funkcie Trigger
Trigger Mode Mód Triggeru Mód Triggeru Clarification
Close Zavřený Zatvorený Deactivated when triggered
Instant Okamžitý Okamžitý Activated when ARM/HOME ARM
24 Hours 24 Hodin 24 Hodín Activated even when DISARM
Home Režim Doma Režim Doma Deactivated when DISARM/HOME ARM
Door Chime Uvítací Gong Uvítací Gong No alarm but clanking
Delay Zpoždění Oneskorenie Wait few seconds before alarm
Battery replacement instructions/ Výměna baterie/
① Insert the flat blade of a small screwdriver into the pry-off slot of transmitter,
twist the blade to remove the cover.
① Stiskněte tlačítko dolů pomocí palce a druhou rukou otevřete kryt detektoru.
① Stlačte tlačidlo nadol pomocou palca a druhou rukou otvorte kryt detektora.
Features
The iGET SECURITY M3P4 wireless contact sensor is an accessory of iGET SECURITY M3/M4 series smart alarm system.It's fashion
design, energy saving, and low battery warning supported. The main panel will send a SMS to user for battery replacement
when needed.It's easy to setup and works well with most doors and windows. When transmitter and magnet are apart, the
sensor triggers alarm. Two great features:
- Transmitter can be put on either of magnet's left or right side.
Parameters
• Working Voltage DC 3V
• Battery 1x CR2032 button battery (3 V)
• Working Current 20mA
• Standby Current 2μA
• Transmission Distance Without obstacle 200m
• Transmission Frequency 433.29MHz
• Working Temperature -10℃~40℃
• Humidity ≤90%rh (non-condensing)
• Weight 35.5g(battery not included)
• Dimension Transmitter: 80.0mm*38.2mm*13.3mm Magnet: 80.0mm*14.8*12.9mm (L*W*H)
Appearance
Magnet
LED Indicator
LED Indication
LED flashes once: Door/window is opened and transmitter sends signal to the main panel.
LED lights stays on: Low battery, please replace the battery immediately.
Význam Význam
Deaktivován pro všechny režimy alarmu Deaktivovaný pre všetky režimy alarmu
Aktivní když je režim alarmu Aktivován/ Aktívny keď je režim alarmu Aktivovaný /
Režim Doma Režim Doma
Aktívna vždy aj pri režime alarmu
Aktivní vždy i při režimu alarmu Deaktivace
Deaktivácia
Neaktivní pokud je režim alarmu Deaktivace/ Neaktívne ak je režim alarmu Deaktivácia /
Režim Doma Režim Doma
Bez alarmu, ale uvítací gong (např. pro Bez alarmu, ale uvítací gong (napr. pre
obchody) obchody)
Čaká niekoľko sekúnd pred aktiváciou
Čeká několik vteřin před aktivací alarmu
alarmu
Výmena batérie
② Replace with 1x CR2032 battery with the
plus (+) symbol facing up.
② Vyměňte 1xCR2032 baterii, označením plus (+) nahoru.
② Vymeňte 2x CR2032 bateriu, označením plus (+) nahor.
40g(battery included)
PCB Layout
Transmitter
SECURITY M3P4
Installation manual
Instalační manuál
Inštalačný manuál
Website : www.iget.eu E-mail : sales@iget.eu
Operating Instructions
1. Working principle
The transmitter sends trigger signal to main panel paired when the magnet mounted near is moved apart.
2. Pairing with main panel by App
① Scan the QR code printed on the sensor.
② The pairing result would be confirmed by SMS sent from main panel.
Installation & Notice
• Open the case and remove the battery insulative strip.
• Pairing to main panel by App before installing.
• Attach the transmitter and magnet seperately on door/window and its frame with double-side sticky tape or fix with screws.
Transmitter can be put on either of magnet's left or right side.
• Make sure the distance between transmitter and magnet is less than 1cm and at the same level.
• Avoid installing the sensors in area with a large amount of metal or electric wire.
Wireless Contact Sensor
|
| Detektor dveře/okna
| Detektor dvere/okná
Less than 1cm