Download Print this page

NEC N8146-91 User Manual

Dust proof bezel with sensor

Advertisement

Quick Links

Keep this manual carefully along with the product
タワーモデル用防塵ベゼル(センサ付) 取り扱いの手引き
Dust Proof Bezel with Sensor User's Guide
この度は、本製品をお買い上げいただきまして誠にありがとうございます。
Congratulations for your purchase of this Dust Proof Bezel with Sensor.
本製品を取り扱う前に本書の内容をよく読み、指示に従ってください。また、本製品を取り付ける前に、
取り付ける本体に添付の「ユーザーズガイド」に記載されている注意事項も参照してください。 また、増
設にあたっては、最寄りの保守サービスセンターに依頼することをお勧めします。
The User's Guide is intended to allow you to install and use the Dust Proof Bezel with Sensor.
N8146-91 correctly and safely. Read this manual thoroughly before handling the Kit.
In addition, refer to this guide whenever you want to know how to use the Kit or some malfunction occurs.
Always keep this guide at hand so that you can see it when necessary.
For the server in which the Kit is installed, refer to the User's Guide of the server.
Read "Notes on Use" carefully before handling the Kit.
安全上のご注意を無視する取り扱いを行うと、装置の故障、人体事故、火災・周囲の機器の損傷を
引き起こす原因となることがあります。
Indicates the presence of a hazard that may result in death or serious personal injury.
オプションの取り付け、 取り外し時は電源プラグをコンセントから抜
き、外部装置と接続しているケーブルを外してください。
故障や感電する恐れがあります。
When you install the option or delete it, unplug the power cord and
extract the cable that has connected to another one.
Otherwise, an electric shock or fire may be caused.
本書に記載されている場合を除き、絶対に分解したり、修理・改造を
行ったりしないでください。装置が正常に動作しなくなるばかりで
なく、感電や火災の危険があります。
Do not disassemble, repair, or modify the server. Otherwise, an
electric shock or fire may be caused.
大切に保管してください
N8146-91
警告
WARNING
CBZ-001279-091-00
電源プラグを抜く
Unplug the power
cord!
感電注意
Precaution against
electric shock
分解禁止
Prohibition of
disassembly
発火注意
Indicates that
improper use may
cause fire.
感電注意
Precaution against
electric shock
CBZ-001279-091-00

Advertisement

loading

Summary of Contents for NEC N8146-91

  • Page 1 The User's Guide is intended to allow you to install and use the Dust Proof Bezel with Sensor. N8146-91 correctly and safely. Read this manual thoroughly before handling the Kit. In addition, refer to this guide whenever you want to know how to use the Kit or some malfunction occurs.
  • Page 2 CBZ-001279-091-00 本製品使用上のご注意 Notes on Using the Product 本 製 品は 塵 埃侵入防止にのみ効果が有ります。塩害、腐食性ガスには効果 が 有 りません。 This product has an effect only in the prevention from dust invasion. IMPORTANT It has no effect in damage from salt and corrosive gas. 構成品 Composition article 項番...
  • Page 3 CBZ-001279-091-00 第三者への譲渡 Transfer to Third Party 本製品を第三者へ譲渡(または売却)する場合には、本書を一緒にお渡しください。 Make sure to provide this manual and all the accessories along with the product to a third party. 製品の取り付け/取り外しについて Installing or Uninstalling an Internal Optional Device 準 備 確認事項 Notes before carrying out the work (1) 危...
  • Page 4 CBZ-001279-091-00 取り付け Installing N8146-91 in Server 1 . 準備確認事項 Preparation point to be checked (1) 危 険 防 止 及び故障防止のため、作業を行なう際には本体装置の電源スイッチを O FF にし、電源 プラグをコンセントから抜いてください。 To avoid danger and prevent malfunction, turn off the power of the server and unplug the power plug from the outlet before performing the installation.
  • Page 5 CBZ-001279-091-00 ③図のように防塵ベゼルの背面側からセンサ接続用ケーブルを引き出し、目詰まり検出センサに 接続します。 Pull the sensor cable from rear face of dust-proof bezel, and connect to filter replacement sensor as shown in figure below. ④防塵カバーを元通り取り付けます。 Install the dust proof cover to dust proof bezel as shown in figure below. ② ①...
  • Page 6 CBZ-001279-091-00 ⑤防塵ベゼル背面側のセンサ接続用ケーブルをブラケットで固定します。 Secure sensor cable with bracket. センサ接続用ケーブル Sensor Cable ブラケット Bracket ブラケット固定用ネジ Screw for fixing Bracket ⑥本体装置のフロントベゼルを開いて、上方向にスライドさせ、取り外します。 Lift the front bezel of the server as shown in figure below, then remove the front bezel. ② フロントベゼル Front Bezel ①...
  • Page 7 CBZ-001279-091-00 ⑦本体装置にスプリング(3 箇所)を取り付けます。 Install the 3 springs to the server as shown in figure below. スプリング固定用ネジ スプリング Screw for fixing spring Spring ⑧防塵ベゼルを本体装置に取り付けます。 Install the dust-proof bezel to the server as shown in figure below. ヒンジの先端を筺体の穴に差し込みます。(3 箇所) Insert the three hinges of front bezel into the holes of server.
  • Page 8 CBZ-001279-091-00 ⑨本体装置のサイドカバーを取り外します。 Remove side cover of the server. ① ② ⑩本体装置からサブベゼルを取り外します。上下 4 箇所のツメの付近を押しながら装置前面方向に 取り外します。 Remove sub-bezel of the server. Push the around catches (four places on top and bottom), and pull the sub-bezel. サブベゼル Sub-bezel...
  • Page 9 CBZ-001279-091-00 ⑪図のようにサブベゼルにセンサ接続用ケーブルを通します。 Route the sensor cable in sub-bezel as shown in figure below. マザーボード接続側 防塵ベゼル側 To Mother Board From Dust-proof Bezel センサ接続用ケーブル Sensor Cable 40mm ほど余裕をもたせてください Secure about 40mm between dust-proof bezel. ⑫サブベゼルを本体装置に取り付けます。このとき、センサ接続用ケーブルが USB コネクタの奥を 通るように配線してください。 Install the sub-bezel, then pass the sensor cable through back of USB connectors. セ...
  • Page 10 CBZ-001279-091-00 ⑬図のようにセンサ接続用ケーブルを配線し、本体装置内に引き込みます。 Route the sensor cable as shown in figure below. ⑭センサ接続用ケーブルのコネクタをマザーボードに接続します。 Connect the sensor cable to the connector on motherboard. 装置背面 装置前面 Rear Front 目詰まり検出センサ接続用コネクタ Filter Replacement Sensor Connector...
  • Page 11 CBZ-001279-091-00 防塵フィルタの交換 Replacement of Dust-proof Filter 防塵フィルタの推奨使用期間は 6 か月、最大使用可能期間は 1 年となっております。 上記期間は使用環境により前後いたします。交換用防塵フィルタは N8147-28 を使用してください。 The service life of dust-proof filter is six months (recommended) or one year (maximum). The life time depends on usage environment. Use N8147-28 Dust-proof filter for replacement. フ...
  • Page 12 Filter Monitor Software Install 目詰まり検出ソフトウェアのインストール手順については、添付 CD-ROM 内の “目詰まり検出ソフトウェア操作説明書”をご確認ください。 Regarding the installation procedure for the Filter Monitor Software, refer to “Filter Monitor Software Instruction Guide” in the attached CD-ROM. N8146-91 タワーモデル用防塵ベゼル(センサ付) 取り扱いの手引き N8146-91 Dust Proof Bezel with Sensor User’s Guide CBZ-001279-091-00...