Be sure to wind the unwound tape with the unit in the horizontal position.) Rotate Gear Worm clockwise using a screwdriver until the mecha is in the eject state. Remove the tape. (Refer to Fig. 2) Model No.: VCR-S607 Version: 1.0...
Page 5
All manuals and user guides at all-guides.com -5 - Model No.: VCR-S607 Version: 1.0...
10. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging Wrist-strap device. (Be sure to remove it prior to applying power--this is an electric shock precaution.) Model No.: VCR-S607 Version: 1.0...
Page 7
15 Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 16 Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last. Model No.: VCR-S607 Version: 1.0...
Page 8
Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards. Model No.: VCR-S607 Version: 1.0...
Press the “TEST” button on F-AV PCB/Main PCB/Function PCB to set the adjustment mode. b. If the corresponding adjustment button is pressed, the adjustment is performed automatically. When the adjustment is completed, be sure to turn the power off. Model No.: VCR-S607 Version: 1.0...
Page 10
All manuals and user guides at all-guides.com -10 - Location of adjustment button of remote control Model No.: VCR-S607 Version: 1.0...
Page 11
All manuals and user guides at all-guides.com -11 - SW718 location for adjustment mode setting Model No.: VCR-S607 Version: 1.0...
Page 12
All manuals and user guides at all-guides.com -12 - Mechanical Adjustment Note : Refer to the Mechanical Manual “TS-10A (AC82-00023A)” for the adjustment and confirmation of ass’y full deck. The number and position of test point Model No.: VCR-S607 Version: 1.0...
Page 13
5. Press the “MENU” button of remote control again to store the option number. (“PLEASE WAIT” is displayed for a second as shown Fig. 2-5 and this setting is completed.) 6. Turn the Power off. Model No.: VCR-S607 Version: 1.0...
Page 14
All manuals and user guides at all-guides.com -14 - <Table 2-1 NVRAM Option Number> Models Option Numbers VCR-S607(S) 6, 7, 8, 9, 10, 15, 15, 20, 22, 25, 27, 29, 35, 38, 42, 47, 52, 55, 56, 57, 60, 61, 64 Model No.: VCR-S607 Version: 1.0...
All manuals and user guides at all-guides.com -34 - BLOCK DIAGRAM LINE IN LA71750 XT301 : 4.433619 MHz LINE OUT & A2/NICAM (IC4N01) LA72646M IC605 24C081 M37760M Model No.: VCR-S607 Version: 1.0...
Page 35
Resistor are in ohms, 1/8W unless otherwise noted. Special note: Most semiconductor devices are electrostatically sensitive and therefore require the special handling techniques described under the “electrostatically sensitive (ES) devices” section of this service manual. BLOCK IDENTIFICATION OF MAIN PCB Model No.: VCR-S607 Version: 1.0...
Page 36
All manuals and user guides at all-guides.com -36 - Model No.: VCR-S607 Version: 1.0...
Page 37
All manuals and user guides at all-guides.com -37 - S.M.P.S. Model No.: VCR-S607 Version: 1.0...
Need help?
Do you have a question about the VCR-S607 and is the answer not in the manual?
Questions and answers