Advertisement
Quick Links
SYMBOLS ON THE AIRTAP
Caution / Warning
AirTAP System Glide Sheet is a Type B Applied Part
Class II Double Wire Insulated
Consult Instructions for Use
Not made with natural rubber latex
R21025C Rev.000 © 2017 Sage Products LLC
SYSTEM
™
Prevalon
Patient Repositioning System
Operator's Manual
Weight capacity: 550 lbs. / 250 kg
Model #7211
Model #7215
Contents:
Contents:
•
•
(2) 30-Degree Body Wedges
(2) 30-Degree Body Wedges
•
•
(1) Prevalon AirTAP System
(1) Prevalon AirTAP System
Glide Sheet
Glide Sheet
•
•
(1) Microclimate Body Pad
(6) Microclimate Body Pads
Model #3010-F — Replacement Filter for model number 7450
Model #7465 — HEPA Equipped Replacement Filter for model number 7455
Model #7460 — Hose Protection Sleeve for model number 7455
Patents: www.sageproducts.com/patents
™
Model #7455
Model #7450
Contents:
Contents:
•
•
(1) Prevalon Air Pump,
(1) Prevalon AirTAP System
120V
Booster Pump, 120V
Manufactured for: Sage Products LLC
3909 Three Oaks Road • Cary, Illinois 60013
800-323-2220 • +1 815-455-4700
www.sageproducts.com
™
Advertisement
Related Manuals for Sage Products Prevalon AirTAP 7211
Summary of Contents for Sage Products Prevalon AirTAP 7211
- Page 1 Model #7465 — HEPA Equipped Replacement Filter for model number 7455 Model #7460 — Hose Protection Sleeve for model number 7455 Manufactured for: Sage Products LLC 3909 Three Oaks Road • Cary, Illinois 60013 800-323-2220 • +1 815-455-4700 Patents: www.sageproducts.com/patents www.sageproducts.com R21025C Rev.000 © 2017 Sage Products LLC...
- Page 2 • DO NOT operate the Air Pump / Booster Pump if it has a damaged cord or plug, if it is not working properly, or if it has been testing was not performed. Compatibility tests did not show artifacts. Based on rationale, the Glide Sheet with Microclimate Body Pad is damaged or dropped. Contact Sage Products at 800.323.2220 for repair or replacement. electronically non-conductive and non-magnetic.
- Page 3 Prevalon ™ ™ AirTAP System Booster Pump Patient Repositioning System PART IDENTIFICATION Point of Care Power Button Hose Retainer Cord Reel 30º Body Wedges AirTAP System Glide Sheet Flexible Inflation Hose Anchor Wedge Upper Wedge Head of Bed Indicator Easy Roll Handles High-Tech Fabric Power Cord Hanging Clip...
- Page 4 SET UP THE GLIDE SHEET 3. Grasp the Nozzle. With your free hand, separate the fabric of the Valve. 4. Insert the Hose into the Valve until the gray portion of the Nozzle is no 1. With bed brakes locked and bed rails raised, place the bed in a horizontal position, longer visible.
- Page 5 TURNING THE PATIENT 2. Remove the Wedges if present by grasping the corner and slowly rotating out. 3. Set the sending and receiving support surfaces as close together as possible. Ensure 1. Caregiver A and Caregiver B stand on opposite sides of the bed. Lock the bed Sending and Receiving surfaces the bed brakes are locked.
-
Page 6: Cleaning And Disinfecting
EASY ROLL HANDLES REMOVING LINENS 1. The gray Easy Roll Handles may be used to assist with positioning the patient. WARNING: Make sure the bed rails are raised and the bed brakes are Always follow your facility’s safe patient handling procedures. locked. - Page 7 3. Ensure the patient is centered on the Glide Sheet and the Glide Sheet is centered on the bed. Contact Sage Products at 800.323.2220 for repair or replacement. 4. Tuck the Bottom edge of the linen beneath the patient’s pillow, Glide Sheet, and shoulders.
-
Page 8: Part Identification
PREVALON AIR PUMP FILTER REMOVAL AND REPLACEMENT Split image: Booster at foot 1. Unplug the Air Pump from the wall. of bed and hanging from footboard PART IDENTIFICATION 2. Rotate Filter counterclockwise until released from housing. 3. Pull Filter rearward to remove. Dispose of filter according to your facility’s policy. STEP 1 4. - Page 9 AIRTAP SYSTEM BOOSTER PUMP FILTER REMOVAL AND REPLACEMENT 1. Unplug the Booster Pump from the wall. FILTER REPLACEMENT 2. Remove the Hose by removing it from the Nozzle Holder and Hose Retainer. PART IDENTIFICATION 3. Remove the power cord by lifting the retention tab upwards and STEP 1 pulling the cord from the receptacle.
- Page 10 6. Place the new filter over the end of the motor head and ensure that the threaded BOOSTER PUMP & AIR PUMP TECHNICAL SPECIFICATIONS rod passes through the end of the filter. 7. Pull the elastic end of the filter all the way down so that it covers the yellow band. Product Code 7450 7455...