Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for IFM DV13 0 Series
Summary of Contents for IFM DV13 0 Series
- Page 1 Operating instructions 3-segment signal light DV13x0 DV23x0...
-
Page 2: Table Of Contents
DV13x0 DV23x0 3-segment signal light Contents Preliminary note ............. Symbols used . -
Page 3: Preliminary Note
3-segment signal light DV13x0 DV23x0 1 Preliminary note You will find instructions, technical data, approvals and further information using the QR code on the unit / packaging or at www.ifm.com. 1.1 Symbols used Requirement Instructions Reaction, result [...] Designation of keys, buttons or indications... -
Page 4: Safety Instructions
DV13x0 DV23x0 3-segment signal light 2 Safety instructions • The unit described is a subcomponent for integration into a system. – The system architect is responsible for the safety of the system. – The system architect undertakes to perform a risk assessment and to create documentation in accordance with legal and normative requirements to be provided to the operator and user of the system. -
Page 5: Intended Use
The unit is not suited for environments with particular requirements on mechanical stability (e.g. shock/vibration). The unit is intended for indoor use only. u Observe the operating conditions (Ò Technical data at www.ifm.com). The unit is not approved for safety-related tasks in the field of operator protection. -
Page 6: Function
The IODDs necessary for the configuration of the unit, detailed information about process data structure, diagnostic information, parameter addresses and the necessary information about the required IO-Link hardware and software can be found at www.ifm.com. -
Page 7: Installation
Attach the signal lamp to the fixture or the base (overlapping marks) and turn clockwise by approx. 10 ° to fix it. Integrated seals at the bottom of the fixture and in the base as well as O-rings at the fixture and base prevent ingress of moisture. Information about available accessories at www.ifm.com... -
Page 8: Electrical Connection
DV13x0 DV23x0 3-segment signal light 6 Electrical connection The device must be connected by a qualified electrician. Observe the national and international regulations for the installation of electrical equipment. Voltage supply according to EN 50178, SELV, PELV. The IO-Link port must be connected according to the IO-Link specification. u Disconnect power. -
Page 9: Operating And Display Elements
3-segment signal light DV13x0 DV23x0 7 Operating and display elements Parameter setting button (only DV13x0) LED segment 1 with 4 RGB LEDs LED segment 2 with 4 RGB LEDs LED segment 3 with 4 RGB LEDs Buzzer (only DVx310 and DVx330) Feedback LED (only DV13x0) -
Page 10: Operation
DV13x0 DV23x0 3-segment signal light 8 Operation 8.1 Operation of the IO-Link version 8.1.1 General Connect the unit to an IO-Link master (A port) using a 4-pole connection cable. The controller switches the individual LED segments on and off in the configured colours according to the set parameters. -
Page 11: Operation Of The Standard Version
The unit is connected to the digital outputs of the controller via an 8-pole cable (see accessories at www.ifm.com). The HTTL inputs of the signal lamp are triggered with 24 V DC. According to the set parameters the LED segments are on and the buzzer sounds (if present). -
Page 12: Parameter Setting
The parameters of the device can be set using an IO-Link parameter setting tool IO-Link (Ò / 6). IO Device Description (IODD) with all parameters and process data of the unit can be found at documentation.ifm.com. 9.2 Standard version u Turn the transparent protective cover anticlockwise by approx. 10 ° and remove it. - Page 13 3-segment signal light DV13x0 DV23x0 Parameter Value seg. Brightness 100 % 75 % 50 % 25 % Colour green orange blue purple tur- white yellow quoise Frequency low flash low flash low flash high high high rate rate rate flash flash flash slow...
-
Page 14: Maintenance, Repair And Disposal
DV13x0 DV23x0 3-segment signal light 10 Maintenance, repair and disposal Cleaning the unit: u Disconnect the unit from the voltage supply. u Clean the unit from dirt using a soft, chemically untreated and dry micro-fibre cloth. The operation of the unit is maintenance-free. Only the manufacturer is allowed to repair the unit.