Full Gauge Controls d-core Quick Start Manual

Have this manual in the palm of your
hand using the FG Finder application.
WARNING
BEFORE INSTALLING THE CONTROLLER, WE RECOMMEND THAT YOU READ THE ENTIRE
INSTRUCTION MANUAL IN ORDER TO AVOID POSSIBLE DAMAGE TO THE PRODUCT.
PRECAUTIONS WHEN INSTALLING THE PRODUCT:
Before performing any procedure on this instrument, disconnect it from the power source;
Make sure that the instrument has adequate ventilation, avoiding installation on panels containing
devices that may cause it to operate outside the specified temperature range;
Install the product away from sources that may generate electromagnetic disturbances, such as: motors,
contactor, relays, solenoid valves, etc;
AUTHORIZED SERVICE:
Product installation or maintenance may only be performed by qualified professionals;
ACSESSORIES:
Use original Full Gauge Controls accessories only.
If you have any questions, please contact technical support.
AS IT CONSTANTLY EVOLVING, FULL GAUGE CONTROLS RESERVES THE RIGHT TO CHANGE THE
INFORMATION CONTAINED IN THE MANUALAT ANY TIME, WITHOUT PRIOR NOTICE.
1. DESCRIPTION
D-Ceor and T-Copre are electronic controllers for refrigeration dedicated to freezers, beverage displays
and refrigerated cabinets. These controllers can activate cooling, defrost, fan and lighting systems. In
addition, it allows to pre-define up to 4 operating temperatures that are easily changed by its touch-sensitive
keyboard (touchpad) for freezers with rotation of different products.
The controller supports 2 temperature sensors for the control of the refrigerated environment and intelligent
defrost control (start and end of defrost by time or temperature). For a better use for energy, it can control
ventilation during the cycle of the compressor and use Smooth Defrost, a defrosting technique that reduces
the final temperature of the electrical resistance and the amount of heat emitted.
Using its digital input, door opening can be monitored and economic setpoint, defrost or Fast Freezing can
be activated. The Fast Freezing function is an alternative for speed up the cooling process, recommended
for use after the process of replacing products in the freezer.
In addition , T-Core controller has system voltage monitoring where the operation of the equipment can be
limited to only a safe voltage range, reducing the chance of electrical damage due to the power supply.
2. AP LICA P TIONS
- Beverage displays;
- Refrigerated display cabinets.
3. TECHNICAL SPECIFICATIONS
Controller supply
Control temperature
Operating temperature
Resolution
Maximum relay current
Digital input
Operating humidity
Front dimension (with frame)
Front cutout dimension
Base module dimension
4. INDICATIONS AND KEYS
9 - LED power
save mode indication
8 - LED compressor
indication
7 - LED pre-defrost,
defrost or drainage
indication
5 - LED lamp indication
6 - LED fan indication
DIGITAL REFRIGERATION CONTROLLER WITH
TOUCH-SENSITIVE KEYS
Power Touch Manual Function
save mode screen defrost lock
85~240Vac (50/60Hz)
-50 to 60°C (-58 to 99°F)
0 to 60 °C (32 to 140
0.1°C between -9.9 and 9.9°C and 1°C in the
remainder of the range. 1°F across the range
COMP: 10(8)A / 250Vac 1HP - compressor output
DEFR: 7A / 250Vac - defrost output
FAN: 3(2)A / 250Vac - 1/10HP - fan output
LIGHT: 2(2)A / 250Vac - lamp output
Configurable dry contact type
10 to 90% UR ( thout condensation) wi
100 x 54 x 22mm (3,9 x 2,1 x 0,8")
91 x 45mm ( 3,6 1,7 x
116 x 88 x 27mm (4,6 x 3,5 x 1,1")
10 - LED temperature unit indication
1 - Increase key
2 - SET key
3 - Decrease key
4 - Power save mode key
Turn off Sound Serial
alarm
control functions programming
5. BASIC OPERATIONS
5.1 Change the preset
To select the desired preset , press the corresponding key for seconds until the
then release it.
press for
4 se conds
5.2 Turn the economy mode on / off
turn power save mode on / off, press the ECO
To
release it.
press for
8 econds s
5.3 Disable the alarm
To disable the audible alarm, quickly press any of keys 1 , 2, 3 or 4.
5.4 Manual defrost
°F)
To start/stop a manual defrost, regardless of programming, press key 1 for 8 seconds until the message
[dF] appe ars , then release The message it.
press or f
8 seconds
") 5.5 View process step and current desired temperature (setpoint)
To check which process step is being performed, press key "3" for 4 seconds until the
appears, then release it. The current process step is displayed followed by the desired operating
temperature (setpoint) relative to the operating mode (normal/power save).
press or f
4 seconds
4 message
Preset 1
Preset 2
Preset 3
Preset 4
release the
key
key for seconds until the 8 [EC] message appears hen
On
Off
release the
key
[On] will be shown when it starts, and [Of] when it is stopped.
On
Off
release the
key
Current
step
Fan delay
Refrigeration
release the
key
Pr -defrost e
Defrost
Drainage
Fast Freezing
dl
Compressor delay
Displays the current desired
temperature (setpoint)
ex: (2.0ºC)
[Pr]
appears,
, t
[St]
message