Related Manuals for Ruwac DS1 Series
Summary of Contents for Ruwac DS1 Series
- Page 1 USA Industrial Vacuums Quiet Vac: Installation, Operation, Maintenance & Service Model No. Serial No. Filter No. Start-Up Date • Quiet Vac • Quiet Vac Version: V2.2 12.7.21 54 Winter St. • Holyoke, MA 01040 • (413) 532-4030 • info@ruwac.com...
-
Page 2: Table Of Contents
Table of Contents Contents Page Warranty Safety III. Start-Up Inspection and Maintenance Standard Instructions (All Vacuums) Trouble Shooting VI. Terms and Conditions Questions? Call Ruwac USA at (413) 532-4030 or e-mail us at info@ruwac.com! -
Page 3: Warranty
RUWAC service personnel are covered by a 120-day parts only warranty. RUWAC, Inc. will not assume any responsibility under the terms of this limited warranty on equipment, which has not been paid in full. This warranty does not apply to any equipment that has been disassembled, repaired, or otherwise altered by any person without the written authorization of RUWAC’S service department, nor does it apply to any product that has... -
Page 4: Safety
Safety CAUTION: Standard Ruwac DS1 series machines are not to be used for the removal of liquids or any volatile, viscous, flammable or explosive media. If you are unsure about your application requirements consult your Ruwac representative. CAUTION: Standard Ruwac DS1 series machines are designed for continuous use, provided the vacuum is not held under constant stress. - Page 5 Note: If continuity is not found across any of these points, consult the parts manual to check that all ground wires are in place. For further assistance, contact Ruwac.
-
Page 6: Start-Up
This will The dustpan should ensure that excess be emptied after ever material sticks to the use. filter. Questions? Call Ruwac USA at (413) 532-4030 or e-mail us at info@ruwac.com! - Page 7 Note: Using an object to dislodge material may tear the filter. Consult your RUWAC representative if material blockage is excessive. Do not use high pressure compressed air or water to clean off filter, as material may become permanently lodged into filter membrane.
-
Page 8: Inspection And Maintenance
NOTE: The presence of material in this area or in the exhaust is often the result of a misaligned seal or damaged filter. Consult your RUWAC representative if either is the case. Questions? Call Ruwac USA at (413) 532-4030 or e-mail us at info@ruwac.com! - Page 9 Inspection & Maintenance DS1 SERIES STANDARD INSTRUCTIONS: FILTER INSTALLATION CAUTION: Motor deck will be heavy and will require a hoist to remove. Always wear a dust mask when performing filter inspections or service. Re-insert black mesh Insert the filter cage...
- Page 10 13. motor to loosen the belt. Questions? Call Ruwac USA at (413) 532-4030 or e-mail us at info@ruwac.com!
- Page 11 Inspection & Maintenance DS1 SERIES STANDARD INSTRUCTIONS: TURBINE REPLACEMENT NOTE: The turbine is not field serviceable and must be replaced as one unit if defective. Replacement of the motor belt or turbine will require the turbine seal to be replaced.
- Page 12 2 hours or until dry (not tacky). CAUTION: Motor deck will be heavy and will require a crane to place atop work bench or table. Questions? Call Ruwac USA at (413) 532-4030 or e-mail us at info@ruwac.com!
- Page 13 Inspection & Maintenance DS1 SERIES STANDARD INSTRUCTIONS: BELT TENSIONING CAUTION: Motor deck will be heavy and will require a hoist to remove. Before any maintenance service is done, follow standard lock out and tag out procedures as well. Measure belt tension...
- Page 14 (see pg. 10 for of torque. of the motor sheave belt removal matches this height. instructions). Re-install the belt and adjust to proper tension (see pg. 13). Questions? Call Ruwac USA at (413) 532-4030 or e-mail us at info@ruwac.com!
-
Page 15: Troubleshooting
Troubleshooting PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Insufficient Vacuum - Motor in wrong direction - Check motor direction and ensure it is Pressure moving clockwise. - Dustpan improperly seated - Remove dustpan, inspect seal, replace dustpan. - Filter clogged or improperly - Follow filter inspection procedure (Section IV.) seated - Clogged hose... -
Page 16: Terms And Conditions
Buyer shall set aside and hold rejected goods without further processing until RUWAC has an opportunity to inspect and advise of the disposition, if any, to be made of such goods. In no event shall any rejected goods be returned reworked, or scrapped by Buyer without the express written authorization of RUWAC. - Page 17 LIMITED WARRANTY: RUWAC warrants that new equipment which are complete units and are sold and/or manufactured by RUWAC, Inc. will be free from defects in material and workmanship for a period of 18 months from date of shipment or 12 months from date of start-up, whichever comes first. RUWAC warrants that replacement parts sold hereunder will be free from defects in material and workmanship for a period of 120-days after the date of shipment.
- Page 18 RUWAC. RUWAC’S failure to strictly enforce any right on one occasion does not constitute a waiver of that or any on any other occasion.
Need help?
Do you have a question about the DS1 Series and is the answer not in the manual?
Questions and answers