Do you have a question about the SA-WMSP2 and is the answer not in the manual?
Questions and answers
Michael kojo Duho
March 10, 2025
my speaker goes on and off during usage what could be the cause
1 comments:
Mr. Anderson
March 10, 2025
The Sony SA-WMSP2 speaker could turn on and off during usage due to several possible reasons:
1. Power Supply Issues – Fluctuations or interruptions in the power supply could cause the speaker to power cycle. Ensure the power cord is securely connected and that the outlet is functioning properly.
2. Overheating Protection – If the internal components overheat, the speaker may turn off as a safety measure. Ensure adequate ventilation around the unit.
3. Faulty Connections – Loose or damaged RCA input cables may cause signal interruptions, leading to intermittent power cycles. Check and secure all connections.
4. Speaker Protection Circuit – The built-in protection circuit may activate due to excessive volume levels or electrical faults, shutting down the speaker to prevent damage. Try reducing the volume level.
5. Internal Component Failure – A failing power supply unit, capacitors, or other internal electronic components could cause instability. Professional inspection may be required.
6. Auto Power Feature – If the unit has an automatic power-saving mode, it may turn off when no signal is detected. Ensure a consistent audio signal is being sent.
If the issue persists, servicing may be necessary.
Page 1
US Model Canadian Model Ver 1.0 2002. 02 AEP Model UK Model E Model • SA-WMSP2 is the sub woofer section in HT-DDW740. • SA-WMSP4 is the sub woofer section in photo: SA-WMSP4 silver model HT-DDW840. SPECIFICATION POWER OUTPUT AND TOTAL...
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
Page 3
SA-WMSP2/WMSP4 SECTION 1 DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) Note on Printed Wiring Boards: Note on Schematic Diagram: • X : parts extracted from the component side.
Page 4
SA-WMSP2/WMSP4 • CIRCUIT BOARD LOCATION LED board INPUT JACK board SWITCH board MAIN board POWER TRANS board CONTROL board...
SA-WMSP2/WMSP4 SECTION 3 CONTROL INPUT JACK ELECTRICAL PARTS LIST MAIN NOTE: • Due to standardization, replacements in the • COILS When indicating parts by reference number, parts list may be different from the parts uH: µH please include the board name.
SA-WMSP2/WMSP4 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...
Need help?
Do you have a question about the SA-WMSP2 and is the answer not in the manual?
Questions and answers
my speaker goes on and off during usage what could be the cause
The Sony SA-WMSP2 speaker could turn on and off during usage due to several possible reasons:
1. Power Supply Issues – Fluctuations or interruptions in the power supply could cause the speaker to power cycle. Ensure the power cord is securely connected and that the outlet is functioning properly.
2. Overheating Protection – If the internal components overheat, the speaker may turn off as a safety measure. Ensure adequate ventilation around the unit.
3. Faulty Connections – Loose or damaged RCA input cables may cause signal interruptions, leading to intermittent power cycles. Check and secure all connections.
4. Speaker Protection Circuit – The built-in protection circuit may activate due to excessive volume levels or electrical faults, shutting down the speaker to prevent damage. Try reducing the volume level.
5. Internal Component Failure – A failing power supply unit, capacitors, or other internal electronic components could cause instability. Professional inspection may be required.
6. Auto Power Feature – If the unit has an automatic power-saving mode, it may turn off when no signal is detected. Ensure a consistent audio signal is being sent.
If the issue persists, servicing may be necessary.
This answer is automatically generated