Related Manuals for IECHO 450W
Summary of Contents for IECHO 450W
- Page 1 Hangzhou IECHO Science & Technology Co., Ltd. 450W Router User Manual Hangzhou IECHO Science & Technology Co.,Ltd...
-
Page 2: Table Of Contents
Hangzhou IECHO Science & Technology Co., Ltd. Catalog 1. Summary........................2 2. Risk control warning....................2 3. Milling system composition and working principle........... 3 4. Technical parameter....................4 5. Essential of Router installation...................4 5.1. Installation of the suction pipe bracket of the cutting head......4 5.2. -
Page 3: Summary
Hangzhou IECHO Science & Technology Co., Ltd. 1. Summary The 450 Router adopts German imported electric spindle as the core body of the milling tool, with stable speed and superior performance. It is suitable for engraving and engraving of non-metallic hard materials, such as acrylic board, MDF board, aluminum-plastic board, Foam board and other materials. - Page 4 Hangzhou IECHO Science & Technology Co., Ltd. 3、4、5 1- Cutting head 6- Router hose holder 2- Milling tool 7- Router controlling box 3- Dust suction pipeline 8- Dust cleaner 4- Driver cable 9- Power Indicator 5- Air cooling pipeline 10- Power switch...
-
Page 5: Technical Parameter
Hangzhou IECHO Science & Technology Co., Ltd. 4. Technical Parameter Items Parameters Output Power S1:420W,max.500W Range of rotation 6000-60000rpm Motor type Three-phase asynchronous motor Motor protection level IP55 frequency 100-1999Hz Voltage Current S1:6.6A,max.8A Torque S1:8.4Ncm,max.8.4Ncm Air pressure requirement min0.04MPa Collet maxɸ5.0mm... -
Page 6: Connection Of Router Spindle With Cable And Air Pipe
Hangzhou IECHO Science & Technology Co., Ltd. Pic 2 Installation of the suction pipe bracket of the cutting head 5.2. Connection of router spindle with cable and air pipe Before connecting the milling spindle and the drive cable, please check whether there is anything in the plug and clean, then insert the plug straight to the end after aligning the position. -
Page 7: Emergency Stop Cable Connection
Hangzhou IECHO Science & Technology Co., Ltd. 5.3. Connection of emergency stop cable The three-pin plug of the emergency stop cable is connected with the emergency stop control interface on the outside of the milling tool control box, and the two-pin plug is connected with the emergency stop control interface of the milling tool on the electrical box of the cutting machine. -
Page 8: Usb Communication Cable Connection
Hangzhou IECHO Science & Technology Co., Ltd. 5.5. USB communication cable connection Pass one end of the mini USB data cable through the wire hole of the milling tool control box and connect it to the milling driver. Connect the USB plug of the data cable to the USB port of the computer. - Page 9 Hangzhou IECHO Science & Technology Co., Ltd. （Figure. 8） Start the SycoDrive software, as shown in Pic 9, a green light is displayed in the lower left corner of the page, indicating that the drive is successfully connected to the computer.
- Page 10 Hangzhou IECHO Science & Technology Co., Ltd. (1) In the Motor Parameter Sets column, set the spindle model according to Pic 10. （Figure. 10） The 450 milling spindle model is 4033-AC, and the maximum speed is set to 100000rpm. Click the [Load motor type] button on the page. The following prompt pops up, indicating that the import was successful.
-
Page 11: Spindle Running-In
Hangzhou IECHO Science & Technology Co., Ltd. The following prompt pops up, indicating that the save is successful. （Figure. 13） 6.2. Spindle running-in To start the milling tool for the first time, the spindle must be run-in. The spindle manufacturer has done the initial run-in before the product leaves the factory. -
Page 12: Communication Settings Between Router And Computer
Hangzhou IECHO Science & Technology Co., Ltd. During the running-in process, you can view the progress bar to display the running-in progress, as shown in the picture. （Figure. 15） Until the following window pops up, indicating that the running-in is complete. - Page 13 Hangzhou IECHO Science & Technology Co., Ltd. （Figure. 17） Note: Normally, WINDOWS 7/10 system can automatically recognize and install the driver. If the driver cannot be installed automatically, you need to install the serial port driver manually, and the serial port number will be generated after installation.
-
Page 14: Spindle Rotating Direction Confirmation
Hangzhou IECHO Science & Technology Co., Ltd. （Figure. 18） 6.4. Confirm spindle rotation direction When first time using, please make sure whether the spindle direction is correct (as shown in the figure). If it is not correct, please check if the cable connected properly. -
Page 15: Power On
Hangzhou IECHO Science & Technology Co., Ltd. Steps for usage: (1) Preparation (including installing the blade, setting the spindle speed, cutting speed and other parameters); (2) Edit cutting data in iBrightcut software and send it to Cutterserver. (3) Place the material, turn on the suction and fix it;... -
Page 16: Blade Installation
Hangzhou IECHO Science & Technology Co., Ltd. 7.3. Blade installation The 450W router is equipped with 3.5mm or 4mm blade collet, corresponding to the blade ER1 or ER2 respectively. Please select it correctly when using it. Blade installation steps: (1) Place the blade collet into the spindle nut;... -
Page 17: Communication Serial Port Settings
Hangzhou IECHO Science & Technology Co., Ltd. （Figure. 23） 7.5. Communication serial port settings With Cutterserver software, open [System Configuration]-[Serial Configuration] to set the milling router serial port. (Figure. 24) 7.6. Set knife depth Select the milling router icon and click the manual tool setting icon to open the manual tool setting window. -
Page 18: Router Rotating Speed Setting
Hangzhou IECHO Science & Technology Co., Ltd. (Figure. 25) Note: The knife must be adjusted again after each blade change. Hold down the Ctrl key of the computer keyboard during manual tool setting to speed up the cutting speed 7.7. -
Page 19: Daily Maintenance Of Router
Hangzhou IECHO Science & Technology Co., Ltd. 0.04MPa). Excessive air pressure can damage the grease or lubrication system of the bearing. If the bearing loses lubrication, the bearing will be damaged under the high-speed state of the spindle; if the air pressure is too small, the sealing effect cannot be achieved. -
Page 20: Router Driver Alarm And Troubleshooting
Hangzhou IECHO Science & Technology Co., Ltd. 1. When installing the bit, it is necessary to leave a row groove 1. Check whether the router is Bit exposed length = Bit flute installed correctly length + 1mm Router bit 2. Check for nicks or residues on 2. -
Page 21: Warning Codes And Error Codes
Hangzhou IECHO Science & Technology Co., Ltd. On or Blink Warning: code is greater than 6 Blink Error, the code is less than 6 (the number of flashes is the code number) In the error alarm state, a serious problem has... - Page 22 Hangzhou IECHO Science & Technology Co., Ltd. (Figure. 26) When a warning message appears, the milling cutter can still run, and the warning message can be reset during operation. Warning Fault Reason Solution code Motor current exceeds The motor load...
- Page 23 Hangzhou IECHO Science & Technology Co., Ltd. Rated speed limit Parameter Check the parameter "rated activated "rated speed" or speed", limit the rated value analog value "minimum speed" and input is too high "maximum speed", adjust the fixed frequency 1 to 4...
- Page 24 Hangzhou IECHO Science & Technology Co., Ltd. The offset Internal fault Switch twice. If the self-check circuit fault still exists, send in current the inverter for repair. measurement is too large Actual motor The actual refractive Set the rated speed to...
- Page 25 Hangzhou IECHO Science & Technology Co., Ltd. Warning Fault Reason Solution code No motor type The parameter "motor Check the parameter designation type" is set to "no "Motor Type" motor" Cool the motor and Temperature The engine may be reduce the load; test the monitoring excessive;...
-
Page 26: Common Faults And Solution To Router
Hangzhou IECHO Science & Technology Co., Ltd. 10.3. Common faults and treatment of milling cutters (1) An error is reported when starting the milling cutter. (Figure. 27) Possible reasons: the communication port is set incorrectly; the power of the milling cutter is turned off;... - Page 27 Hangzhou IECHO Science & Technology Co., Ltd. (4) When changing from other tools to milling cutters, the lock catch cannot be installed in the positioning rod. Possible reason: The direction of the tool holder of the machine head needs to be modified (non-tool direction parameter).
-
Page 28: Statement
The copyright of this technical document belongs to Hangzhou IECHO Science & Technology Co., Ltd. (hereinafter referred to as IECHO). IECHO does not make any guarantee for this technical document, and IECHO is not responsible for any misunderstandings that may be caused by users of this technical document.