Advertisement
Quick Links
pmvmounts
Mounting instructions for Professional extendable projector mount
Fits to flat ceiling
Maximum projector fixing points up to 630mm x 325mm - Up to 25Kgs
Model No.
PMVMOUNT7
Projector Mount assembly kit
Button head bolt
A -
M8 x 75mm
Nut
B -
M8
Washer
C -
M8
Grub screw
D -
M6 x 8mm
Projector Fixing Kit
Button head screw
E -
M6 x 8mm
Screw
M3 x 10mm
M4 x 10mm
F-
M5 x 10mm
M6 x 10mm
Screw
M3 x 25mm
G-
M4 x 25mm
M5 x 25mm
M6 x 25mm
Washer
M3,
M4,
H-
M5,
M6
I-
Spacer
Struts
Short,
J-
Medium,
Long
2
Attach pole
Ÿ
Ÿ
.co.uk
Ÿ
Ÿ
Ÿ
Factory No.
Ÿ
Z0874FIX1M
Ÿ
x1
x1
x1
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x20
x2
NOTE:
of each
Ÿ
a
A
NOTE:
Do not over-tighten bolt 'A' shown in Stage 2b above.
Ÿ
When inserting Grub Screws 'F' as shown in Stage 2c above, insert finger-tight so all
Ÿ
screws are at an equal depth against inner pole. Then tighten with allen key. Do not over-
tighten these Grub Screws.
Read these instructions carefully before installing your equipment.
Install the mount in a suitable location using fixings which are appropriate for
the ceiling material and structure. Consult a qualified builder if you're in any doubt as
to the structural integrity of the ceiling.
Do not attempt to alter or modify any part of the ceiling mount or its attachments.
Do not use if any parts are broken or appear to be damaged.
Tighten all bolts and fixings securely. Only use fixings provided with this bracket.
Do not mount your projector close to sources or heat or moisture.
Always have a minimum of two persons to install the projector on to the mount.
Projector Mount assembly parts
Projector mount
Pre-assembled pole section
1
Attach mount to ceiling
If in any doubt of the suitability of the
ceiling, it's construction or what type of
fixings to use, consult a qualified builder or
installer.
b
C
B
Ceiling mount
c
D
x4
Advertisement
Related Manuals for PMV Mounts PMVMOUNT7
Summary of Contents for PMV Mounts PMVMOUNT7
- Page 1 Ÿ Model No. Factory No. Do not mount your projector close to sources or heat or moisture. Ÿ PMVMOUNT7 Z0874FIX1M Always have a minimum of two persons to install the projector on to the mount. Ÿ Projector Mount assembly kit...
- Page 2 Attach struts to projector mount Alternative fitment... Attach projector mount and struts to all threads Note: Use the appropriately sized fixings from the fixing kit. Use spacers as required, not always necessary.
- Page 3 Attach projector mount to pole section Remove both tilt and tilt lock washers and large M8 x 75mm bolt from bottom of pole section. Position the hooks on the projector mount over the corresponding parts of the lower moulding. Continued... Position both tilt and tilt locking washers and insert large M8 x 75mm bolt Note: This is the tilt adjustment mechanism.
- Page 4 Adjust the projector Rotation: Adjusted via the telescopic pole clamps. Always take the weight of the projector before releasing the pole clamp. Tilt locking mechanism Tilt: Adjusted via the tilt locking mechanism between the pole section and projector mount Loosen retaining bolt and tighten at desired angle. Yaw: Fine adjusted via the projector mount.
Need help?
Do you have a question about the PMVMOUNT7 and is the answer not in the manual?
Questions and answers