Silencer 432SR Quick Reference Install Manual

REMOTE START with KEYLESS ENTRY SYSTEM
FOR PROFESSIONAL INSTALLATION ONLY!
If you are not proficient in the installation of this product or would like a full version
of the installation manual, please visit our web site @www.magnadyne.com
Fortin or iDatalink
Bypass Module
Receiver/Control
Center(RCC)
Pink: (+) Ignition 1 Input/Output
Red: +12V Input 30A
Violet: Starter Output
Pink /White: Ignition 2 Output
Orange: Accessory Output
Red: +12V Input
30A
Red: +12V Battery Power
15A
Brown: (-) Horn Output
Black: System Main Ground
White: Parking Light Relay Output
White: Parking Light Relay Power Input 10A
Blue: - Negative Door Unlock Output
Green: - Negative Door Lock Output
16 15 14 13 12
16 Pin Accessory Harness Wiring:
8 7 6 5 4 3 2
Pin Color Function
1 Green/White (-) Factory Alarm Re-Arm Output
2 Gray (-) Hood Pin Safety Input
3 Black/White (-) Parking Brake Input
4 Open None
5 Brown (+) Vehicle Brake Safety Input
6 White/Blue External Activation Input
7 Yellow (+) Ignition Output (to alarm)
8 Lt. Violet/White Tach Input (AC)
16 PIN
(see chart)
11 10 9
1
Pin Color Function
9 Orange (-) GND When Armed/Lock
10 Red/White (-) Channel 3 Output (Trunk)
11 Lt. Purple/Yellow (-) Starter Output
12 Lt. Green/Black (-) Factory Alarm Disarm Output
13 Blue/White (-) 2nd Status/Defrost Output
14 Dk. Blue (-) Status Output
15 Orange/White (-) Accessory Output
16 Pink (-) Ignition Output

Mounting the Receiver/Control Center (RCC):

1. Choose a location on the upper or sides of the vehicle windshield.
A higher location is best.
2. Remove the backing liner from the mounting tape on the backside of the
RCC and stick it to the windshield glass.
3. Route the RCC cable to the location of the control module.

Programming System Features:

All SILENCER remote start systems have a menu of features that can
be programmed to suit the installation requirements of any vehicle.
These features can be set by using the RCC button Feature Programming
procedure or by Windows PC programming and the SILENCER web app.

Feature Programming by RCC Button

1. Open the drivers door.
2. Turn the ignition key ON then OFF.
3. Within 5 seconds, press and hold the RCC button to select the menu.
- A single chirp and LED flash indicates Menu #1.
- Hold the button longer for two chirps and two LED flashes.
You are in menu #2.
4. When the desired menu is reached, release the RCC button.
5. Within 5 seconds, press and release the RCC button the number of
times corresponding to the feature you want to change then press and
hold the button once more to lock the feature. Chirps and LED flashes
will confirm the feature chosen. Release the button. Use the buttons on
the SILENCER remote to adjust the feature.
6. For features with only two options, the = 1 Chirp setting,
while the = 2 Chirp setting.
7. For features with more than two settings, the button selects the
settings in ascending order. Horn chirps indicate which option is selected.
8. Turn on the igntion key to exit Feature Programming.

Menu #1 (Default in Bold)

Chirps
Item Feature
1 2 3 4 5 6 7
ADS
1 Data Protocol Fortin
Ignition
2 Off On
Locking
Ignition
3 Off On
Unlock
Panic with
4 Off On
Ignition On
Door Lock
5 0.8 sec. 3.5 sec. 0.4 sec.
Pulse
Double Pulse Off On
6
Lock (Single) (Double
Double Pulse Off On
7
Unlock (Single) (Double)
Factory Alarm
8 Single Double
Disarm Pulse
Remote
Factory Alarm With Before
9 Start
Disarm Unlock Unlock
Only
Panic
10 Horn Output 20 ms 30 ms 40 ms 50 ms
Only
Comfort
11 Off CC1 CC2
Closure
Quick Reference Install Guide

Menu #2 (Default in Bold)

Chirps
Item Feature
1 2 3 4
Transmission
1 Automatic Manual
Type
Engine Checking Wireless Wired
2 Voltage Off
Mode Tach Tach
3 Cranking Time 0.6 sec 0.8 sec 1.0 sec 1.2 sec 1.4 sec 1.6 sec 1.8 sec 2.0 sec 4.0 sec
Remote Start
4 12 min 24 min 60 min
Run Time
Anti-Grind
5 On Off
Output
Diesel Start Timed Timed Timed
6 Off
Delay 15 sec 30 sec 45 sec
ACC Output
7 During Diesel Off On
Wait to Start
2nd Ignition
8 Ignition 1 ACC
Behavior
Rear
Blue / White GND Rear
Defog
9 Wire When Defog
Latched
Behavior Running Pulse
10 min
External Trigger
10 1 Pulse 2 Pulse 3 Pulse
Pulse Count
Parking Light
11 Constant Flashing
Behavior
Timer Mode Run
12 12 min 3 min 6 min 9 min
Time
Access another feature within the same menu
1. Press and release the RCC Button the number of times to advance from
the last feature programmed to the next feature to be programmed.
2. Press the RCC button and hold it.
3. Use the SILENCER remote and follow steps 5 or 6 above to adjust
the feature.
Access another menu
8 9
1. Press and hold the RCC Button
2. After 3 seconds, the system will advance to the next menu and conform
with chirps and LED flashes.
Exiting the feature program mode
1. Set the ignition key to ON. A long confirmation chirp will be hear if a
horn or siren is connected.
2. Automatic after 30 seconds with no input from the RCC button
(long chirp).
3. The RCC button has been press too many times (long chirp).

Feature Programming by PC/App

1. A windows computer with internet support is required. The APP supports
Windows 7 (sp1) thru Windows 10 (Apple/Mac computers are not supported)
2. The programming adaptor model #ALA-21P is required
3. Follow the instructions provided with the ALA-21P accessory.
5 6 7 8 9