Download
Share
Print this page
Graco 234533 Instructions - Parts Manual
  1. Manuals
  2. Brands
  3. Graco Manuals
  4. Cleaning Equipment
  5. 234533
  6. Instructions - parts manual
Graco 234533 Instructions - Parts Manual

Graco 234533 Instructions - Parts Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Instructions/Parts
Cleaning System
234533
For use with Multi-Orifice Linear Streaming Applicator (MOLSA) to apply automotive Liquid Applied
Sound Deadener (LASD) materials.
100 psi (0.68 MPa, 6.8 bar) Maximum Working Pressure
120° F (35° C) Maximum Fluid Temperature
Read warnings and instructions.
See table of contents, page 2.
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2003, Graco Inc. is registered to I.S. EN ISO 9001
310623A

Advertisement

loading

Summary of Contents for Graco 234533

  • Page 1 100 psi (0.68 MPa, 6.8 bar) Maximum Working Pressure 120° F (35° C) Maximum Fluid Temperature Read warnings and instructions. See table of contents, page 2. Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2003, Graco Inc. is registered to I.S. EN ISO 9001...

  • Page 2: Table Of Contents

    Setup ........4 Graco Information ......10 Maintenance .

  • Page 3: Warnings

    Check equipment daily. Repair or replace worn or damaged parts immediately. • Do not alter or modify equipment. • Use equipment only for its intended purpose. Call your Graco distributor for information. • For professional use only. • Locate away from traffic areas, sharp edges, moving parts, and hot surfaces.

  • Page 4: Setup

    Setup Setup . 1: Typical Installation Key: Tank Assembly Sponge Secondary Float Valve Primary Float Valve Air Pressure Regulator Filter Valve Diaphragm Pump Primary Reservoir Spray Bar Sponge Holder Drain Valve Filter Housing Water Supply Valve Rollers Spray Bar Bolt 310623A...
  • Page 5 Adjust the air pressure regulator (C) to the diaphragm Starting the pump pump (D). The pump should cycle once every second Graco Husky 515 Diaphragm pump (D52966) is used in (approximately 20 psi [0.14 MPa, 1.4 bar]). this tank assembly. Refer to your Graco Diaphragm...

  • Page 6: Maintenance

    Maintenance Maintenance Cleaning and replacing roller assembly With use, the water will become saturated with the LASD material. If rotation of the rollers or the pump 1. While rollers (P) are running through clean water, cycle rate slows down, you should change the water in rub rollers with your hands until build up of contami- the tank.
  • Page 7 Maintenance Draining remaining water 5. Close both valves (G) and (K) that isolate both recir- culating filters. 1. While clean water is circulating from the spray bar, wipe the walls and bottom of reservoir until clean. 6. Remove the filter housings (N) and screen elements 112302.

  • Page 8: Parts

    MOLSA Cleaning System 14, 15 Ref. Ref. Part No. Description Qty. Part No. Description Qty. 119205 HOUSING, axle 234533 TANK, assembly 119206 SPRING, guide 118865 SPONGE 119211 TUBE, spring 118864 ROLLER 119209 VALVE, float secondary 119055 SPRING 119207 PIN, left 119056 AXLE...

  • Page 9: Technical Data

    Technical Data Technical Data Maximum Fluid Working Pressure 100 psi (0.68 MPa, 6.8 bar) Maximum Air Pressure 100 psi (0.68 MPa, 6.8 bar) Dimensions 36 x 27 x 25.75 in. (914 x 686 x 654 mm) Mounting Leg Dimensions 24.5 x 25.5 x .44 in. mounting hole diameter (622 x 648 x 11 mm mounting hole diameter) Wetted Parts 300 series stainless steel, brass, plastic, polypropylene,...

  • Page 10: Graco Standard Warranty

    With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.